Topic: Duox 2 On 1.6 (Read 375 times)

Mattyb2001uk · « **on:** February 01, 2005, 01:18:00 PM »

I have just installed a DuoX 2 White version in a Crystal. When I turn the xbox on the red light on the chip flashes, Green light on the front stays on but I get no picture. It works fine with the chip disabled. Any Ideas?

antz1970 · « **Reply #1 on:** February 01, 2005, 01:38:00 PM »

i know its a stupid suggestion , but you do have it switched to bank 1 for v1.6(im assuming the white cromwell edition is the same as the blue one with 2 banks)? , other than that recheck your lpc wiring , altho it sounds like it could be a cromwell incompatibility with your 1.6 but i really aint sure

also im sure i read thatsome people have probs with a/v leads other than the one you get with xbox , again not 100% sure tho

**edit** oops sorry just done some reading on the white duox , i was wrong , it dont matter what bank you use , sorry i would still try bank 1 tho

Mattyb2001uk · « **Reply #2 on:** February 01, 2005, 01:43:00 PM »

Yeah its on bank 1. You cand hear the DVD power up and HDD, just nothing on the screen. I have a version 1.2 with a DuoX White 2. Should I flash that with the M8 bios then try that in the 1.6. I redone the LPC wiring again aswell.

antz1970 · « **Reply #3 on:** February 01, 2005, 01:48:00 PM »

was just reading on team executors website that flashbios3.03 (the one on bank 1) may not work on a v1.6 ,(its seemingly fine on a v1.6b lol)id try hotswapping it in your other xbox and try m8 1.6 remember and link bt to quicksolder point 9 to be able to hotswap

Mattyb2001uk · « **Reply #4 on:** February 01, 2005, 01:51:00 PM »

QUOTE(antz1970 @ Feb 1 2005, 08:54 PM)

was just reading on team executors website that flashbios3.03 (the one on bank 1) may not work on a v1.6 , id try hotswapping it in your other xbox and try m8 1.6 remember and link bt to quicksolder point 9 to be able to hotswap

antz1970 · « **Reply #5 on:** February 01, 2005, 01:59:00 PM »

point g on the duox2 install diagrams for v1 - 1.5 or its the 2nd pad down from d0 on chip

ModdingManiac · « **Reply #6 on:** February 01, 2005, 01:59:00 PM »

DELETED..SEE BELOW

ModdingManiac · « **Reply #7 on:** February 01, 2005, 02:04:00 PM »

Disregard my previous reply..didn't realize you were talking about another system..so yes follow antz reply about hotswapping

Mattyb2001uk · « **Reply #8 on:** February 01, 2005, 02:18:00 PM »

What do I need to do in the Evox.ini?

antz1970 · « **Reply #9 on:** February 01, 2005, 02:34:00 PM »

shouldnt need to do anything m8

Mattyb2001uk · « **Reply #10 on:** February 01, 2005, 03:01:00 PM »

Triple checked everything, Rebuild, all solder joints, Flashed with M8 plus but still no picture! Need urgent help!

antz1970 · « **Reply #11 on:** February 01, 2005, 03:12:00 PM »

are you using the standard a/v cable?

Mattyb2001uk · « **Reply #12 on:** February 01, 2005, 03:23:00 PM »

Yeah. I wos wondering, I have the pin between A and B soldered could that be it?

Mattyb2001uk · « **Reply #13 on:** February 01, 2005, 04:37:00 PM »

Please!!!! Anyone have any ideas?

ModdingManiac · « **Reply #14 on:** February 01, 2005, 04:48:00 PM »

QUOTE(Mattyb2001uk @ Feb 1 2005, 10:29 PM)

Yeah. I wos wondering, I have the pin between A and B soldered could that be it?

Author Topic: Duox 2 On 1.6 (Read 375 times)