xboxscene.org forums

Author Topic: X Chip On Version 1.0 Xbox  (Read 67 times)

decline1822

  • Archived User
  • Newbie
  • *
  • Posts: 34
X Chip On Version 1.0 Xbox
« on: October 02, 2004, 10:40:00 PM »

are you sure the d0 is correct?
Logged

n82tweeder

  • Archived User
  • Newbie
  • *
  • Posts: 10
X Chip On Version 1.0 Xbox
« Reply #1 on: October 02, 2004, 10:42:00 PM »

99% sure, i looked at the manual that came w/ installing the xchip from eb2k and in it it says where the d0 point is, and that's what point i pushed it to.
Logged

n82tweeder

  • Archived User
  • Newbie
  • *
  • Posts: 10
X Chip On Version 1.0 Xbox
« Reply #2 on: October 02, 2004, 10:52:00 PM »

and i'm pretty sure this is a v 1.0 xbox, it has the conexant video ship w/ the fan in the middle next to the fins for the heatsink
Logged

n82tweeder

  • Archived User
  • Newbie
  • *
  • Posts: 10
X Chip On Version 1.0 Xbox
« Reply #3 on: October 02, 2004, 11:30:00 PM »

ok, i got it to stop fraging, now i got into the xchip bios, but now i'm suppose to put in a bootcd right? because i put slayer's newest version on a rewritable and it has worked in the past every time. is there a step i'm missing in there? thanks
Logged

MikeDaMan

  • Archived User
  • Newbie
  • *
  • Posts: 1
X Chip On Version 1.0 Xbox
« Reply #4 on: October 03, 2004, 05:49:00 PM »

how did you get yours to stop fragging? I have a 1.0 also but those little pins on the solderless adapter seem to love to move around when you move the xbox a little. I'll have it all hooked up and working but once everything is put back together...yup back to fragging any suggestions?
Logged

cravavr3

  • Archived User
  • Sr. Member
  • *
  • Posts: 279
X Chip On Version 1.0 Xbox
« Reply #5 on: October 04, 2004, 08:31:00 AM »

Push solderless adapter flush with motherbaord or X-Box, then verify contact is good, then tighen screw snugly.  Not too tight as you may strip screw hole.
Logged

Easybuy2000

  • Archived User
  • Full Member
  • *
  • Posts: 197
X Chip On Version 1.0 Xbox
« Reply #6 on: October 04, 2004, 09:00:00 AM »

The solder-less adapted should be flush with the Xbox motherboard and the pogo pin tips (sharp ended points) should be centered in the LPC holes BEFORE you tighten down the adapter. This make sure that it "digs" in the soldered holes of the LPC and makes a good contact. The screw should be tighten but not too tight that you strip it off. The solder-less adapter should not move at all when all is done. Make sure that the D0 wire is inserted in the correct hole and it's making good contact with the outer ring of the DO hole of the Xbox.

Logged

kasserole

  • Archived User
  • Newbie
  • *
  • Posts: 10
X Chip On Version 1.0 Xbox
« Reply #7 on: October 10, 2004, 03:34:00 PM »

SO the xbox v1.0 has solder in the lpc hole, so do i just put the adapter on top of them, or do i have to remove the solder?
Logged