Topic: Xchip Wont Work W/o Usb Connceted Help! (Read 47 times)

Minus_Sign · « **on:** July 28, 2004, 04:44:00 PM »

i just got my x-chip working, and get my original cromwell bios to load on occasion.(sometimes it resets 3x then frags) but i can only get it to work while connected to the computer with the usb cord and x-control running. if i remove the usb cord, it boots to the ms dash, as if the chip isnt in but the chip's LED lights up.

Also, i tried booting up the Evox dashboard with a cdrw.(when i got the xecuter to load from the cromwell menu.) shouldnt the Xecuter allow me to boot up the cd? if not whats wrong? Plz help!!!

christineyoung · « **Reply #1 on:** July 29, 2004, 06:02:00 AM »

Use Xcontrol software and make your boot bank the bank you installed xecuter bios to.

Minus_Sign · « **Reply #2 on:** July 29, 2004, 11:47:00 AM »

Thanx! I got my X-chip working without the usb attached to it. But now, I need to load a new dashboard onto it. I chose Evolutionx, i made it an ISO image with the program xISO, and burned it to a cdrw(Memorex). i burned it as low as i could,which was 4x with Nero ver.6. i put it into my xbox and it still cant recognize the disc! Can you help me???

christineyoung · « **Reply #3 on:** July 29, 2004, 04:16:00 PM »

Sometiems i find with cd-rw media is it needs a few attempst at reading, other times the media is not compatible, i have had success with verbatin cdrw on thompson drives which are the horible drives to find compatibility for.

DVD-R should almost work on any drives.

Minus_Sign · « **Reply #4 on:** July 29, 2004, 05:29:00 PM »

I have a Samsung drive, which is the best of the 3 isnt it? and dont i need a DVD burner to write on DVD-Rs?

and also, my x-chip doesnt always boot to my xecuter bios. sometimes it just goes straight to thems dash,even though i did what you said.

thanx alot for all your help so far!
hope i can get this thing working!

christineyoung · « **Reply #5 on:** July 29, 2004, 06:30:00 PM »

If it boots elsewhere somtimes would assume loose connection, try tightening solderless adapter scew

Minus_Sign · « **Reply #6 on:** July 29, 2004, 08:06:00 PM »

I actually went through the solderless adaptor guide again and realized i hadnt put in any rivets. I put in the rivets, and the x-chip boots every time! now all i need to do is get evox burned onto a dvd-r.Is it possible to burn an xiso image onto a dvd-r using only a cd burner? or do you need a dvd burner???

Thanx for your help so far!!

ddkore · « **Reply #7 on:** July 30, 2004, 04:37:00 PM »

If you have a samsung, you should be able to use a cheap CD-R. not need to use RW

Minus_Sign · « **Reply #8 on:** August 06, 2004, 02:41:00 PM »

Use Xcontrol software and make your boot bank the bank you installed xecuter bios to.

cravavr3 · « **Reply #9 on:** August 07, 2004, 09:46:00 AM »

When you power xbox after flashing evox 1.0 on chip do you see a purpel logo on top left of screen?

Are you powereung unit form Power button and not pressing Eject?

Author Topic: Xchip Wont Work W/o Usb Connceted Help! (Read 47 times)