xboxscene.org forums

Pages: 1 [2]

Author Topic: Matrix Chip And Xbox V1.6 ?  (Read 281 times)

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Chip And Xbox V1.6 ?
« Reply #15 on: November 25, 2004, 06:20:00 AM »

READ FIRST

Here is a Pic for another mod chip install it does say to goto p[in 7 but you can not do this with the matrix becuase the matrix does not have the correct type of lfram for a 1.6 xbox.  once you ground lfram on a 1.6 xbox it will boot of the lpc.  If you connect lfram to the matric ehter pin 7 or the trace  the matrix will be disabled.  So remove the pin 7 pogo and ground lfram wire.  In the pic when it say to goto pin 7 goto ground.

Check my next post for the pic.
Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Chip And Xbox V1.6 ?
« Reply #16 on: November 25, 2004, 06:21:00 AM »

Logged

SSJToo

  • Archived User
  • Newbie
  • *
  • Posts: 14
Matrix Chip And Xbox V1.6 ?
« Reply #17 on: November 26, 2004, 06:24:00 AM »

Hey Exzir, can you check to see if this file is good to go.  I wasn't sure on the numbering of the pins in the matrix and I wanted to make sure before uploading it to the scene.

http://uploads.savef...nd_v16_xbox.pdf



Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Chip And Xbox V1.6 ?
« Reply #18 on: November 26, 2004, 09:07:00 PM »

The only differance is that i was going to the r8r1 for the 3 volt connection.  Aslong as that point has the proper voltage then it should be a good little pdf file you can distribute.
Logged

muffenz

  • Archived User
  • Newbie
  • *
  • Posts: 5
Matrix Chip And Xbox V1.6 ?
« Reply #19 on: December 01, 2004, 06:17:00 PM »

Hi,

I looked at your PDF, but it seems like the matrix pin you say to remove on fig. 3 looks like it corresponds to pin 3 on the LPC not pin 7...

also, does your chip go solid green when you turn it on ? (ping 1 on pin 2 off?) mine keeps flashing red/green and when i have it in pin 1  and pin2 on (to find the right spot)

Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Chip And Xbox V1.6 ?
« Reply #20 on: December 01, 2004, 06:52:00 PM »

Well the pin 7 is not the lpc pin number sorry for the confusion.  You are correct it is pin 3 and not pin 7.

Just make it enabled all the time.  I don't remember what the jumbers for that are.  Also I made mine writeable or both pins on I think.  that will make the xbox always boot the matrix chip and your good to go.
Logged

Deathman

  • Archived User
  • Newbie
  • *
  • Posts: 15
Matrix Chip And Xbox V1.6 ?
« Reply #21 on: December 04, 2004, 10:45:00 AM »

Would this also work for an xecuter 2.0 on a 1.6?
Logged

Exzir

  • Archived User
  • Full Member
  • *
  • Posts: 248
Matrix Chip And Xbox V1.6 ?
« Reply #22 on: December 04, 2004, 05:04:00 PM »

More than likely not.  If so you might want to check out or ask the question in a excuter forum.
Logged
Pages: 1 [2]