Topic: Matrix Programming (Read 91 times)

mcdonaldpd · « **on:** November 18, 2003, 12:55:00 PM »

When I connect the programmer with the matrix chip attached to my parallel port, the light on the matrix chip is red. the pc will not recognize the chip. i have applied pressure to the chip/programmer connection. I downloaded and installed GiveIO. I even tried another computer. I know when this matrix chip was attached to the xbox mb the light glowed green.

i just bought this modded xbox with the matrix chip already connected. the guy said the chip would be sent without the bios on it. the system fragged when i got it, and i assumed that it was b/c the chip had no bios. i am now starting to wonder if this guy didn't fry this chip.

any suggestions would be great. i am thinking about just getting a xecuter 2 chip or something.

thanks

david

btw: i put a brand new battery in the programmer

also, the system still frags when the matrix chip is out. it doesn't have a stock drive, it has a 40gig hard drive in it. it still frags when i disconnect the ide. does that mean my board is toast or just possibily the tsop needs to be flashed?

rms2001 · « **Reply #1 on:** November 18, 2003, 01:04:00 PM »

Try setting the delay on the programming software higher.

mcdonaldpd · « **Reply #2 on:** November 18, 2003, 01:07:00 PM »

i tried setting the delay at different levels. it didn't help. does the fact that the chip is registering a red light mean anything, or is that standard when connected to the programmer with no bios?

Dankbud · « **Reply #3 on:** November 18, 2003, 01:27:00 PM »

QUOTE (mcdonaldpd @ Nov 18 2003, 11:07 PM)

i tried setting the delay at different levels. it didn't help. does the fact that the chip is registering a red light mean anything, or is that standard when connected to the programmer with no bios?

theres a red light on whether it has a bios on it or not. its letting u know its ready to be flashed....

mcdonaldpd · « **Reply #4 on:** November 18, 2003, 01:34:00 PM »

mcdonaldpd · « **Reply #5 on:** November 18, 2003, 01:42:00 PM »

the matrix is in mode 1. the other pc doesn't have an intel board.

what about the xbox mobo. should it frag when the ide cable is disconnected? i think my hd is locked, also.

mcdonaldpd · « **Reply #6 on:** November 18, 2003, 01:50:00 PM »

i get no video. man, i'm getting frustrated!!!

dankbud, where did you get your chameleon? i saw where a guy sold you one and then sent the money back.

mcdonaldpd · « **Reply #7 on:** November 18, 2003, 01:58:00 PM »

well, i think i am going to get a new board and a chameleon. do you think the 1.8 is neccesary? is a 1.3 sufficient? btw, thank for the help!!

hey, the programmer for matrix is compatible with the new chameleons, right?

mcdonaldpd · « **Reply #8 on:** November 18, 2003, 02:11:00 PM »

i think the 1.8 is compatible with 1.4 and 1.5 mobo, and the 1.3 cham is not.

BTW- Dankbud, put me down as a ref if you want. i'll give you a good review. my email is [email protected]; aim is DavieMac1345

Dankbud · « **Reply #9 on:** November 18, 2003, 02:13:00 PM »

QUOTE (mcdonaldpd @ Nov 19 2003, 12:11 AM)

i think the 1.8 is compatible with 1.4 and 1.5 mobo, and the 1.3 cham is not.

BTW- Dankbud, put me down as a ref if you want. i'll give you a good review. my email is [email protected]; aim is DavieMac1345

ah ha, ic. i dont got 1.4 or 1.5 so it dont matter to me. hehe. anyways, thanks man, i added u to my aim. mines : ixifour20ixi ttyl man. GL.

Author Topic: Matrix Programming (Read 91 times)