xboxscene.org forums

Author Topic: Matrix With V1.1 Xbox  (Read 168 times)

blackout_19

  • Archived User
  • Sr. Member
  • *
  • Posts: 352
Matrix With V1.1 Xbox
« on: January 09, 2003, 05:35:00 AM »
You need to fill the holes on a v1.1 with solder first. Then, the led will only briefly flash green and then go red. It still means that it's properly aligned though.
Logged

blackout_19

  • Archived User
  • Sr. Member
  • *
  • Posts: 352
Matrix With V1.1 Xbox
« Reply #1 on: January 09, 2003, 06:18:00 AM »
If you don't then the pogo pins will keep falling through and it will never connect properly.
Logged

Saga

  • Archived User
  • Newbie
  • *
  • Posts: 3
Matrix With V1.1 Xbox
« Reply #2 on: January 09, 2003, 10:04:00 AM »
Worked for me W/O soldering anything on a xbox 1,1 but you need to clean the holes on the motherboard to get the stuff of that ms put on there for 1.1 versions. After doing that the matrix will work
Logged

tammoomy

  • Archived User
  • Newbie
  • *
  • Posts: 27
Matrix With V1.1 Xbox
« Reply #3 on: January 09, 2003, 10:34:00 AM »
and after i clean it do i let the pogo pins drop in the holes or no?
Logged

007jamesbond

  • Archived User
  • Full Member
  • *
  • Posts: 170
Matrix With V1.1 Xbox
« Reply #4 on: January 09, 2003, 11:36:00 AM »
You`ll need to fill the holes, really, if you had a v1.0 xbox it wouldnt needed to be done, cause the holes there are already filled
Logged

Saga

  • Archived User
  • Newbie
  • *
  • Posts: 3
Matrix With V1.1 Xbox
« Reply #5 on: January 09, 2003, 11:59:00 AM »
tongue.gif clean it with a piece of cutton, you gotta rubb pretty hard aftert hat just put the matrix in spot and screw it on there
it will make contact. IT works fine for me and i got the matrix just so i DIDNT had to use any solder smile.gif  

beerchug.gif
Logged

tammoomy

  • Archived User
  • Newbie
  • *
  • Posts: 27
Matrix With V1.1 Xbox
« Reply #6 on: January 09, 2003, 01:01:00 PM »
Saga u still ddnt answer my question...
do i let the pogo pins drop in the holes or do i let them settle on the edge?
Logged

Regionfree

  • Archived User
  • Jr. Member
  • *
  • Posts: 51
Matrix With V1.1 Xbox
« Reply #7 on: January 09, 2003, 01:25:00 PM »
The easiest way I foind to aligne the matrix on a V1.1 is to screw it down first, (not too tight so you can still move it) than with a malty meater check the connection between the D0 pin on the Matrix and pin 5 on the TSOP. Not feeling in the holes with solder actualy helps to aligne the chip. Works for me every time.
Cheers...
Logged

TGD

  • Archived User
  • Full Member
  • *
  • Posts: 133
Matrix With V1.1 Xbox
« Reply #8 on: January 09, 2003, 07:12:00 PM »
There is absolutly no need to fill in the holes with solder, thats a bunch of BS. Just take your time and keep going at it. I've installed 4 Matrix chips for friends of mine since they dont know nothing about this stuff. Each one of them all had v1.1 with empty holes but i managed to install a Matrix in each of them just fine.
Logged