Print

[Gazole]

QUOTE (sebene @ Nov 29 2002, 01:07 AM)

hi when u flash , u flash from what the cd or the hd ? cause for me it won t flash from the cd i have to flash from the hd ! i u want to be sure if the matrix is at the right place flash with evox and place the chip then put in it on mode 4 reflash the matrix with tsop_flash then mode 3 and boot on evolution dash from your hd then reflash the xbox bios !!!it really works done 2 today !!!

is it work on v1.1 xbox ,because it work fine on 1.0 but i can't flash on a  1.1 xbox

[knowledgeiv]

This will not work on a v1.1 Xbox.  The special Matrix TSOP flash BIOS was written specifically to do this task, but only for v1.0 Xbox.

[Gazole]

[knowledgeiv]

QUOTE (sebene @ Nov 24 2002, 02:59 PM)

hi flashing tsop with matrix ok once for all i need proof that it actually works !!! because i haven t seen a lot of pepole saying that it works fine as simple as it looks on the picture ! so plz answer so we will know for good that it works !!!!! the chip works fine with evox2.5 and i always get it the first time ! but when i flash with EvoX_MatriX_TSOP_flash all i get even if i move chip is a on and off with a loud clik !!! plz help

                                    do a search; you will find the proof.

[slizzap]

QUOTE (sebene @ Nov 24 2002, 02:59 PM)

hi flashing tsop with matrix ok once for all i need proof that it actually works !!! because i haven t seen a lot of pepole saying that it works fine as simple as it looks on the picture ! so plz answer so we will know for good that it works !!!!! the chip works fine with evox2.5 and i always get it the first time ! but when i flash with EvoX_MatriX_TSOP_flash all i get even if i move chip is a on and off with a loud clik !!! plz help

                                    Works just fine. I flashed 4 myself this weekend. Just make sure you follow the instructions to the letter.

It usually takes me a good 5-10 minutes to get a successful flash. When you attempt to flash it, when you're grounding the T1 wire and turning on the system and the modchip flashes green then red and the system just shuts itself off right away, that indicates the Matrix isn't seated properly. Keep moving it until you get a successful boot. When you ground the wire and turn it on, it should flash green and then turn solid red...after which you can let go of the T1 wire. If you get a successful boot but it gives you an error screen or won't boot your custom dash I'd recheck your solder points.

Hope that helps.

[Xevious]

Yes, the Matrix will flash the TSOP just fine.

[sebene]

hi

on the picture u solder the 3 last pins of the tsop or the 2 last pins to the W2 wire??

[sebene]

is it bad if i have soldered the 2 flash bridges espacially the one in the back

[slizzap]

QUOTE (sebene @ Nov 25 2002, 09:42 PM)

hi on the picture u solder the 3 last pins of the tsop or the 2 last pins to the W2 wire??

                                    You need to solder the 3rd pin (W2) to W1. What the instructions are saying is that the 1st and 2nd pins are not used and therefore you won't cause any harm if you solder the 3 pins together, but the connection is made on the third pin. However, if you solder together pins 3 and 4...then you'll have a problem.

[manschadow]

Yes go on flash the TSOP, if it does not work you only have to pay a new XBOX, that is not hard is it?

[AceX]

[sebene]

hi

when u flash , u flash from what the cd or the hd ?
cause for me it won t flash from the cd i have to flash from the hd !
i u want to be sure if the matrix is at the right place flash with evox and place the chip then put in it on mode 4 reflash the matrix with tsop_flash then mode 3 and boot on evolution dash from your hd then reflash the xbox bios !!!it really works done 2 today !!!