Topic: Flash The Tsop With Matrix & Keep Flashing The.. (Read 139 times)

brankota · « **on:** January 05, 2003, 08:56:00 PM »

why step 17 last? I already have this done, and will be trying the Matrix method this week when it comes in. Do I need to remove it, than resolder it again?

regulater7 · « **Reply #1 on:** November 13, 2002, 05:44:00 PM »

I know i have posted on this alot on this, so i would like to post the completed tutorail i have came up with, to help people have a little better understanding on how to do this, w/o just looking at pictures!

You Need:
Evox Dashboard v1.8.2812
Matrix & Programmer
Any cracked 256K bios other then EvoX_MatriX_TSOP_flash.bin
EvoX_MatriX_TSOP_flash.bin
2- 3" wires

1. Program the matrix via programmer with a bios thats "256k.bin". (any cracked bios thats 256K will do except EvoX_MatriX_TSOP_flash.bin)
2. Install Matrix in xbox.
3. Boot up with Evox cd. (burned on CDrw/dvdr/dvdrw)
4. Copy "xboxdash.xbe","msxboxdash.xbe","evox.ini","bios","Skin" to C: drive. (With a 1meg bios in the bios folder)
5. Eject CD-rw from xbox, and restart.
6. Power up xbox fully, then shutdown. (make sure its all working)
7. Reprogram the matrix via programmer with bios "EvoX_MatriX_TSOP_flash.bin".
8. Solder the TSOP Jumper point on the TOP SIDE of the xbox motherboard. (Only the top side right now)
9. Tape a wire to W1 and W2. (See pictures on forums http://evox.xboxhack...pic.php?p=2677)
10. Tape a wire to T1. (See pictures on forums http://evox.xboxhack...pic.php?p=2677)
11. Install Matrix in xbox. (make sure its set to mode 3)
12. Tape other end of T1 wire to ground screw.
13. Power up xbox fully, then remove the grounded end of the T1 wire.
14. Then Flash TSOP from evox dash.
15. Shutdown the xbox.
16. Remove the Matrix and both Wires.
17. Solder the TSOP Jumper point on the BACK SIDE of the xbox motherboard.
18. Reasemble
19. Done

You Can Now Flash and Reflash the TSOP with any program/dashboard that allows you to do so, and up to a 1meg bios!

Enjoy!

regulater7 · « **Reply #2 on:** November 13, 2002, 06:58:00 PM »

I might be confused about what your asking but. you can still see the A,B,C points stated in the install manual. so thats what i used to aligh it, just make sure no to cover it up with the tape.

thevoiceover · « **Reply #3 on:** November 13, 2002, 09:21:00 PM »

QUOTE (regulater7 @ Nov 14 2002, 12:44 AM)

I know i have posted on this alot on this, so i would like to post the completed tutorail i have came up with, to help people have a little better understanding on how to do this, w/o just looking at pictures!

Isn't this basically everything the tutorial tells you to do in the evox_matrix_tsop_flash.zip file? If you guys do not have that file, I could send it off...

regulater7 · « **Reply #4 on:** November 13, 2002, 10:40:00 PM »

well i didnt get that text file with my flash.bin rar... also im not sure cuz i dont have it.. but i dont think it told people to solder the jumper on the back side to be able to keep flashing it... im not sure though... also i posted it for veravaction for when i did it..

majik655 · « **Reply #5 on:** November 14, 2002, 12:12:00 AM »

Any chance for any pictures that show the jumper to solder on back of xbox mother board.

duff · « **Reply #6 on:** November 14, 2002, 12:17:00 AM »

QUOTE (majik655 @ Nov 14 2002, 07:12 AM)

Any chance for any pictures that show the jumper to solder on back of xbox mother board.

check out this post for pics (4th post):

http://xbox-scene.fx...662b463f3c91e67

regulater7 · « **Reply #7 on:** November 14, 2002, 10:34:00 AM »

what 2 points do you connect to? and what should the reading be... just connectivity?

flashbak · « **Reply #8 on:** November 15, 2002, 06:58:00 AM »

Just curious. Do you mean to literally tape the connection (with tape) or do you mean to use the word 'tack' in place of it?

Author Topic: Flash The Tsop With Matrix & Keep Flashing The.. (Read 139 times)