Topic: Matrix (Read 306 times)

MrEs · « **on:** October 01, 2002, 10:52:00 PM »

go to
start -> run, and type "command"
that gets u a command prompt up
then change to the dir where wmilk is with the "cd" command

then use this command to run wmilk
"wmilk -c -a ffc00000 -v -p mybios.bin"

where mybois.bin is the name of the bios u want to use.. =)
make sure the bois is on the same directory and also u THIS DLL file in the same directory

hope that helped.. =)

sanity · « **Reply #1 on:** October 02, 2002, 11:54:00 AM »

Download the matrix install manual from easybuy2k and read it.

It says where to get the wmilk program and it gives you the EXACT command line you need to type to flash the Matrix chip..

ventsi83 · « **Reply #2 on:** October 10, 2002, 12:46:00 AM »

OK guys, i have problem with my bios
that's the error that milk gives me when i type the command :

Milksop GPL Reflasher - 0.12 - ©2002 [email protected]

CHEAPLPC on printer port at 0x378
LPC bus error - peripheral returned SYNC=0F
LPC bus error - peripheral returned SYNC=0F
error getting device ID at address FFC00000
Device not supported

tried two computers other than mine, with xp and 98, still doesn't work
I don't know what to do
Any suggestions?

Fatty Lumpkin · « **Reply #3 on:** October 10, 2002, 11:07:00 AM »

Same thing ...pinch the programmer and chip with your fingers while you program.

ventsi83 · « **Reply #4 on:** October 10, 2002, 04:27:00 PM »

u mean i have to hold it firmly into the port ?

obiwan · « **Reply #5 on:** October 10, 2002, 04:49:00 PM »

if that doesnt help try another PC to flash

ventsi83 · « **Reply #6 on:** October 10, 2002, 09:50:00 PM »

i tried 6 computers already
none of them worked

cos · « **Reply #7 on:** October 10, 2002, 10:18:00 PM »

Mine is not working either..
I'm almost giving up...

Milksop GPL Reflasher - 0.12 - ©2002 [email protected]

CHEAPLPC on printer port at 0x378
LPC bus error - peripheral returned SYNC=0F
error getting device ID at address FFC00000
Device not supported

This is the message showing even nothing is connect to lpt port.
I assume wmilk can't detect programmer but as soon as I connect
it to lpt port, red led lit up on mod board.
I can't believe I been waiting this crap for couple of weeks..
I wonder how could I get replacement from worst customer service.

mzenone · « **Reply #8 on:** October 10, 2002, 10:30:00 PM »

this may not be of much help....but it may just be mobo, ive tried on gigabyte, biostar- and the only one that worked was a MSI board....

iWYD2003 · « **Reply #9 on:** October 10, 2002, 11:43:00 PM »

you can always sell me the chip

hehe, I have an ASUS mobo, so I will wait and see and try it when my chip comes in.....

ravencry · « **Reply #10 on:** October 11, 2002, 06:13:00 AM »

I think that you should try other brands of Pc's

People have said over and over again that when they used another PC
it worked ok

just go find another pc... and try it..

obscene · « **Reply #11 on:** October 11, 2002, 10:24:00 AM »

tried it on my pc running XP, didnt work.. put it on my laptop, took me a while, but finally got it to work! hold the pieces with ur fingers as u flash!

KneeGrowZ · « **Reply #12 on:** October 11, 2002, 10:37:00 AM »

I have the same problem and I have tried another pc and it didnt work. Can I flash the bios a different way. This sucks. I bought 2 chips because i have 2 xboxes and i cant flash the damn chip.

obscene · « **Reply #13 on:** October 11, 2002, 10:44:00 AM »

hold it with ur fingers, and dont move!

cos · « **Reply #14 on:** October 11, 2002, 11:34:00 AM »

I wonder how do I check
either programmer or chips are bad or not.

Is there any program I can detect programmer
on lpt port ?

Author Topic: Matrix (Read 306 times)