Topic: Xbox V1.6 Modded With Adalin + (Read 240 times)

undertoe · « **Reply #15 on:** July 07, 2004, 03:01:00 PM »

good work, i would like to know what the BT and L1 points are, and if they still function the same as earlier models

BaDvs3viL · « **Reply #16 on:** July 07, 2004, 03:10:00 PM »

I am working on that now........

But what we need to find out is this?

?

Once the LPC Lines are repaired...The xbox frags.......Once you install a chip and ground the D0 (LFrame) It boots from the chip fine.....

Question : Which LPC Line(s) are causing the Frag.....If I can find that out and put a switch on those line(s) as well......

Im going to Uninstall my chip and LPC LAD Lines and make sure the original bios boots ok and then go from there with installing 1 wire at a time and see...

Ill post more tonight

undertoe · « **Reply #17 on:** July 07, 2004, 03:47:00 PM »

ah, I see. well that certainly complicates things

BaDvs3viL · « **Reply #18 on:** July 07, 2004, 03:50:00 PM »

This is very true....

And now that I think about it....In all the videos that I have seen with the 4th gen modchips they all have the V1.6 origianl bios flashed on their chip and booting from there...which I figure is an ok thing to do....But with us with only a 256k bios anyway...that leaves us out......So I am working on this now.....Will have an answer soon.....

MovesInSilence · « **Reply #19 on:** July 07, 2004, 04:21:00 PM »

still not sure why it frags with the chip not active ...and why i can't use a 120gb hdd yet

BaDvs3viL · « **Reply #20 on:** July 07, 2004, 06:29:00 PM »

undertoe · « **Reply #21 on:** July 07, 2004, 07:04:00 PM »

MovesInSilence · « **Reply #22 on:** July 08, 2004, 12:49:00 AM »

how the .... err yep just noticed it
found one interesting thing though ...
When the SST chip is in place on the alladdin board the M$ bios don't want to boot ... remove the SST and the M$ boots

(and no guesses as to why M8 doesn't boot)

I've wired up the BT same as older boards (ignoring the 4th pair of resistors from the plug) and it switches over the chip ... not sure i got the L1 in the right spot now because it stays orange

flyingkiwi · « **Reply #23 on:** July 08, 2004, 12:59:00 AM »

I got a couple of V1.6 working with Akira2 (much the same as adalin) , yeah but i cant get it to boot up original mode by switching off, only by removing chip, anyone found away qround this . Also what is the IGR for M8, am use to xecutor2 bios where IGR works sweet as, is there one for M8 ??

MovesInSilence · « **Reply #24 on:** July 08, 2004, 01:21:00 AM »

can you check yours an confirm ?

just found out if LAD0 is not connected then ordinary bios boots, reconnect it and Mod bios works and ordinary don't

so does that mean Aladdin advance needs a switching LAD0 also ?

BaDvs3viL · « **Reply #25 on:** July 08, 2004, 04:30:00 AM »

anu|b|iss · « **Reply #26 on:** July 08, 2004, 04:55:00 AM »

you can build a switch like that or get one at radio crap

A@ron · « **Reply #27 on:** July 08, 2004, 05:30:00 AM »

DPST (Double pull single throw) is what you need IIRC.

A@ron

BaDvs3viL · « **Reply #28 on:** July 08, 2004, 07:40:00 AM »

I just went out and bought a DPDT since they didnt have a DTSP.....

But O well this well work....

Im installing now and will post back in a couple with pics.....

Thx for all the info

ar_156 · « **Reply #29 on:** July 08, 2004, 10:26:00 AM »

Everything sounds great here, but can somebody tell me how to solder the flashed Aladdin (with M8_16.bin) onto the v1.6???

I can't follow the picture posted here, is there any clearer pictures?

Author Topic: Xbox V1.6 Modded With Adalin + (Read 240 times)