Print

[neonuke]

QUOTE (MastaChef @ Dec 7 2003, 10:50 PM)

"pin33"/ link to 32 connected to ground

I don't think "Pin 33" should be connected to ground. You should have a wire going from "Pin 33's" point on the Mobo to the pin 32 POINT on the Mobo. (Pin 32 is +5v)

[javi]

here is my story...

i flashed a homebrew (am29f040) with a 512K EVOX M7. I did it with my old mobo 1.0. It flashed ok, and it was recognized ok by evox dash md5 checksums.

i had it as backup, just in case a tsop flash went wrong.

now i came across this PAL v1.5.
i installed the chip (as i only have a USA 007AUF).

now the xbox frags.
wiring is ok.
tried 3 different chips with no luck.

i did a lot of USA v1.5 with evox m7 & 007auf... but i'm stucked with this one.

any clue? should i try a homebrew with X2 4981 on it?

FYI, to flash/upgrade a homebrew with evox, as u guys want to do, u have to wire it in a slight different way.. there are 2 pins that change.
PIN 31 should go to #WE in mobo.(it is 5v for normal use)
PIN 24 should go to #OE in mobo (it is GND for normal use).
there is a tut on how to do so...
http://www.xbox-scen...ashhomebrew.php

BUT.. (notice the BIG BUT).. those diags are for 1.0/1.1 mobos...
so here is my problem (and it will be yours too)... there are no diagrams for WE and OE on newer 1.2+..
(those points are NOT the ones u bridge to write enable the tsop.)
unless u know where to wire pins 31 and 24 in new mobo, u wont be able to upgrade the Homebrew.

[dreamjeb]

I found my answers!!

Now I just need to know..... I found the diagram for the homebrew mod on the diagrams page, from the page "diagram for v1/v1.1 xbox"  Can I use this diagram on a 1.4 box??

Thanks for the help!

[ntmts]

DID you get the mod installed on the 1.4? afterall?

[sudo]

Just wondering if u were able to use the 29wire homebrew on the v1.4/v1.5 version?

[Xeero]

Yes, you can use a 29-wire mod on a 1.4/1.5.  It would require you to use EvoX M7 or X2 4979 as the BIOS on the mod.  The changes in the 1.5 (no power or ground in the LPC points) wouldn't affect a 29-wire mod because they use other power and ground points.

[Ozmods]

If you need a good cheap 29 wire chip that is easy to install
Take a look at one that i make it will work on all Version xboxes..

$13 plus shipping..

http://xraychips.com/Xray3.jpg

[lordvader129]

QUOTE (Ozmods @ Dec 2 2003, 10:13 PM)

If you need a good cheap 29 wire chip that is easy to install Take a look at one that i make it will work on all Version xboxes.. $13 plus shipping.. http://xraychips.com/Xray3.jpg

this chip is flashable? like if xbox 1.6 needs yet another new bios i will be able to upgrade this chip to repair TSOPs on a hypothetical 1.6?

if so i want one, lol

[Ozmods]

Yes it is..as you can see it is in a socket if you need to remove the chip..and it is also flashable via Evox dash

[lordvader129]

cool , where do i buy one? lol

[Ozmods]

Pm sent

[dfect]

cool, also wanna buy one, how much is shipping to sweden?

this i can use to re-flash tsop with xbox-scene's tutorial homebrew tsop flash, right?

programmed with xecuter 4979?

where do u ship from, europe, how soon can i get it?, just destroyed a winbond xbox, need new bios fast

[Ozmods]

QUOTE (dfect @ Dec 4 2003, 07:39 PM)

cool, also wanna buy one, how much is shipping to sweden? this i can use to re-flash tsop with xbox-scene's tutorial homebrew tsop flash, right? programmed with xecuter 4979? where do u ship from, europe, how soon can i get it?, just destroyed a winbond xbox, need new bios fast

Shipping is $7

Yes you can use it to flash TSOP

I can either program with M7 or Xecuter 4979 or both

It will take about 7 days to get to you..

Payment can be made via paypal

[networkBoy]

QUOTE (a94cobra @ Dec 3 2003, 02:22 AM)

Don't you have to connect the Lframe?

no.  That's only for the LPC mods
-nB

[dfect]

ok, just give me info how to order, and i'll order one

prog it Xecuter4979/orginal if theres no problem

when flashing myself.., do i just combine 2x256kb to one 512 via xbtool, and then switch bios via jumper/switch?

also what flash address should i put in config files?