Topic: Confused Over A/v Output Diagrams (Read 58 times)

ferrari_rulz_02 · « **on:** August 06, 2005, 05:05:00 PM »

hello there guys.

i got hold of two digrams that allow you to get heaps of different a.v outputs from teh xbox.

i am planning to, on my new case, have a lot of the different a/v outputs, so that i can run it in different modes, depending on where the xbox is. im goign to have three buttons at teh back of my new xbox case that im makign, so i can choose what a/v mode the xbox is in.

the outputs that i want to get are:
-Componet video
-D-Sub Video
-Composite Video
-Sterio Sound (the two rca ones, like the standard av kit)
-Coaxial digital sound

i ripped a board out of my old dvd player, and it has the connections for these.

so anyway, i got hold of these two diagrams:
user posted image

so is it just me, or are the two diagrams conflicting?

cheers

celinedrules · « **Reply #1 on:** August 06, 2005, 08:18:00 PM »

I used the top diagrams to mod my Xbox. I have all the outputs except vga. I followed it exactly ands every thing works. It was really hard to solder all of them though.

ferrari_rulz_02 · « **Reply #2 on:** August 06, 2005, 08:35:00 PM »

QUOTE(celinedrules @ Aug 7 2005, 01:29 PM)

I used the top diagrams to mod my Xbox. I have all the outputs except vga. I followed it exactly ands every thing works. It was really hard to solder all of them though.

celinedrules · « **Reply #3 on:** August 08, 2005, 09:45:00 AM »

I believe you do but I am not positive. The VGA is the only output I didn't do.

ferrari_rulz_02 · « **Reply #4 on:** August 09, 2005, 12:40:00 AM »

QUOTE(celinedrules @ Aug 9 2005, 02:56 AM)

I believe you do but I am not positive. The VGA is the only output I didn't do.

celinedrules · « **Reply #5 on:** August 09, 2005, 06:56:00 AM »

Yeah, I installed three toggle switches in the back of my case.

ferrari_rulz_02 · « **Reply #6 on:** August 09, 2005, 07:33:00 AM »

QUOTE(celinedrules @ Aug 10 2005, 12:07 AM)

Yeah, I installed three toggle switches in the back of my case.

caster420 · « **Reply #7 on:** May 03, 2006, 12:01:00 PM »

Yes, it is possible. I have done this to my xbox and it works very well. The top diagram worked for me.

Caster.

tbirdturbo · « **Reply #8 on:** May 03, 2006, 04:42:00 PM »

so if i am just interste in advanced a/v and hdtv a/v then i can just follow the bottom diagram? maybe stupid question but the top green box with numbers is part of mother board right?, the black square at bottom(#'s 1-21), what is that?

carwarr · « **Reply #9 on:** May 03, 2006, 05:27:00 PM »

The bottom diagram is the pinout of the connector of your video cable/AV pack that plugs into your xbox.

QUOTE(tbirdturbo @ May 3 2006, 03:49 PM)

so if i am just interste in advanced a/v and hdtv a/v then i can just follow the bottom diagram? maybe stupid question but the top green box with numbers is part of mother board right?, the black square at bottom(#'s 1-21), what is that?

carwarr · « **Reply #10 on:** May 03, 2006, 09:14:00 PM »

Yes, you can ignore it. It is handy to have those pinouts if you were going to modify your cable but since you are going to be putting your xbox into a new case, just solder the wires directly to the bottom of the motherboard

And good luck.

QUOTE(tbirdturbo @ May 3 2006, 04:55 PM)

so if i am installing the jacks, i can just ignore that?

nickman · « **Reply #11 on:** May 04, 2006, 08:37:00 AM »

QUOTE(ferrari_rulz_02 @ Aug 7 2005, 01:12 AM)

so is it just me, or are the two diagrams conflicting?

cheers

Hi. What do you mean with conflicting ?
One have VGA output and the other has SCART (A common port in Europe).

I made the second diagram btw.. Is there some other problem i have missed ?

nickman · « **Reply #12 on:** May 04, 2006, 03:10:00 PM »

QUOTE(nachomans @ May 4 2006, 10:45 PM)

I have one clue.....
I dont know why there is a separate ground for any conector...
seems like all the grounds are all the same, right?

It's the same on both pictures. What i wondered about was what is so conflicting between them other then one is for RGB scart and one is for VGA.

carwarr · « **Reply #13 on:** May 04, 2006, 03:14:00 PM »

QUOTE(nachomans @ May 4 2006, 01:45 PM)

I have one clue.....
I dont know why there is a separate ground for any conector...
seems like all the grounds are all the same, right?

tbirdturbo · « **Reply #14 on:** May 05, 2006, 12:05:00 PM »

o.k. couple last questions, before i do this, the bottom diagram will work for a ntsc box correct? also anyone know how i can put led's on the front of case to show me which switches are off and which are on? and is 24 gauge wire o.k. for this?

Author Topic: Confused Over A/v Output Diagrams (Read 58 times)