xboxscene.org forums

Pages: 1 ... 5 6 [7] 8 9 ... 26

Author Topic: Extend The Life Expectance Of Your Modded 1.6  (Read 1156 times)

Bulan

  • Archived User
  • Jr. Member
  • *
  • Posts: 65
Extend The Life Expectance Of Your Modded 1.6
« Reply #90 on: November 25, 2004, 06:03:00 AM »
Added the findings in this thread to my webpage in case needed..
http://xbox.bula.nu/...install_1.6.asp
Logged

menelik

  • Archived User
  • Full Member
  • *
  • Posts: 196
Extend The Life Expectance Of Your Modded 1.6
« Reply #91 on: November 25, 2004, 03:02:00 PM »
can anyone who isnt payed by teamexecuter, smartxx etc. make this here sticky?
Logged

vinyl

  • Archived User
  • Newbie
  • *
  • Posts: 5
Extend The Life Expectance Of Your Modded 1.6
« Reply #92 on: November 26, 2004, 01:35:00 AM »
I believe I read earlier in the thread that a dremel with a fine point cutting tool would do.
Logged

alladdin

  • Archived User
  • Newbie
  • *
  • Posts: 23
Extend The Life Expectance Of Your Modded 1.6
« Reply #93 on: November 26, 2004, 01:55:00 PM »
yes, i did wonder that myself. the trace is on the surface and i used a "stanley"blade, i did worry about going into something in the board tho... is it safe if you make a deep cut  ??
Logged

daddo

  • Archived User
  • Newbie
  • *
  • Posts: 6
Extend The Life Expectance Of Your Modded 1.6
« Reply #94 on: November 26, 2004, 03:26:00 PM »
hold on a moment... i'm gonna chip my 1.6 box with an aladin xt it's good or it also need the resistor?
Logged

nachomans

  • Archived User
  • Full Member
  • *
  • Posts: 196
Extend The Life Expectance Of Your Modded 1.6
« Reply #95 on: November 26, 2004, 03:37:00 PM »
dry.gif
Logged

Troed

  • Archived User
  • Full Member
  • *
  • Posts: 204
Extend The Life Expectance Of Your Modded 1.6
« Reply #96 on: November 27, 2004, 05:31:00 AM »
Did anyone redo the LFRAME measurements on a v1.6 with an X3?

Logged

hippo

  • Archived User
  • Sr. Member
  • *
  • Posts: 497
Extend The Life Expectance Of Your Modded 1.6
« Reply #97 on: November 27, 2004, 05:51:00 AM »
yes I want to know for sure the D0 scheme on X3 aswell.
Logged

Chancer

  • Archived User
  • Hero Member
  • *
  • Posts: 5751
Extend The Life Expectance Of Your Modded 1.6
« Reply #98 on: November 27, 2004, 07:29:00 AM »
with the trace cut and the resistor in the box boots ok unmodded. Fit the chip as normal and chip enable /disable is controlled from the chip.
Logged

alladdin

  • Archived User
  • Newbie
  • *
  • Posts: 23
Extend The Life Expectance Of Your Modded 1.6
« Reply #99 on: November 29, 2004, 04:07:00 PM »
this one seems to have gone cold?   i thought we might have seen some more test results posted.  i saw something sugesting the clevermod is now pulsing also,nothing on the site link i used tho , has it changed....
Logged

nachomans

  • Archived User
  • Full Member
  • *
  • Posts: 196
Extend The Life Expectance Of Your Modded 1.6
« Reply #100 on: November 29, 2004, 11:05:00 PM »
wink.gif

What is worst...LFRAME to ground or LFRAME alone...not connected to anywhere...?
Logged

Morglum

  • Archived User
  • Hero Member
  • *
  • Posts: 977
Extend The Life Expectance Of Your Modded 1.6
« Reply #101 on: December 02, 2004, 04:14:00 AM »
QUOTE
Smartxx has been made aware of the issue on the 1.6 XBox and the rumors that a resistor is needed. Smartxx hasnt ignored this, but they didnt make any statement about it as they heard these rumors because they didnt want to cause a panic among chip owners, ex You must fix your xbox this way or it will die. While adding a resisitor may help, it may also cause more issues for 99% of the peolpe when they are cutting traces on thier motherboard. Smartxx will make a statement when they have other solutions. Till then, if you want to add a resistor and cut the motherboard, go ahead, but be aware that you may cause more problems for yourself if you cut the motherboard in the wrong place etc.


Well i think that pretty much shows thats it IS an issue with SmartXX chips too. Time to buy your resistors everyone.

Part number: 348-0566
Part name: 680R
Website: www.rswww.com
Logged

aerofx

  • Archived User
  • Full Member
  • *
  • Posts: 115
Extend The Life Expectance Of Your Modded 1.6
« Reply #102 on: December 02, 2004, 04:15:00 AM »
Is this the right resistor?  Just want to be sure as I haven't seen anybody post pictures yet.

http://www.radioshac.....t_id=271-1117

user posted image
Logged

yazoo32

  • Archived User
  • Newbie
  • *
  • Posts: 17
Extend The Life Expectance Of Your Modded 1.6
« Reply #103 on: December 02, 2004, 05:30:00 AM »
Where is the proof this does happen? Does it blow your XBox?  has it happened to anyone?  It's all well and good stating it could happen but thats no reason to butcher your motherboard over an eventuality that may never happen.  

Where did this info come from?

All these questions should have been investigted and answered before anyone began soldering resistors.

So I put to all the experts here, can you answer the above questions.

Logged

XplicitContent

  • Archived User
  • Full Member
  • *
  • Posts: 176
Extend The Life Expectance Of Your Modded 1.6
« Reply #104 on: December 02, 2004, 08:18:00 PM »
Um...the diagram in the first post dont work, and I'd like to see it as I am going to do this mod when I do the 1.6 rebuild on my new Xbox. Thanx.
Logged
Pages: 1 ... 5 6 [7] 8 9 ... 26
« previous next »