Topic: Another Broke Xbrick Q?.... (Read 289 times)

BaDvs3viL · « **on:** February 12, 2004, 08:05:00 AM »

Well....I keep getting these messed up xbox's......Now with this one it is a little more simple....This guy tried to install an Xenium and man did he do a job on the D0 point(S)....Top and bottom...I mean they are GONE!.....HAHA....Well with no chip in the xbrick it fraggs....So I assum that the D0 is messed up so bad that it cant boot?....Is that what happens?.....What can I do to fix this problem....I had read a couple tut's....but it doesnt look good..... <

smokeingit · « **Reply #1 on:** February 12, 2004, 08:40:00 AM »

it can still be fixed... you just have to use a 30 gauge wire and fix the briged on it... not hard to do if you have common sense and have a good solder hand. do not try if you dont have either. <

BaDvs3viL · « **Reply #2 on:** February 12, 2004, 08:42:00 AM »

I have both and actually I have all 3..(Wire 2).....anyway....Thanks for the reply and is there something I can see to bridge?..some pic of this or something? <

BaDvs3viL · « **Reply #3 on:** February 12, 2004, 10:58:00 AM »

Can I get somebody to give me a hand on this.....Where can I route the D0 If both top and bottom D0 points trashed? <

lookformeb · « **Reply #4 on:** February 12, 2004, 11:38:00 AM »

Consider get a trace repair kit if you can't bridge the points with to 30ga. Basically its just conductive paint.

This si ebtter served in the General Hardware forums though, not TSOP.

<

BaDvs3viL · « **Reply #5 on:** February 12, 2004, 11:40:00 AM »

Ok Thanks man.......So I could just trace the D0 form the F#$%^& point untill where it ends up and just make a new trace?

Only question is tho....Looks like the whole from top to bottom of the D0 is gone....I dont see any metal at all..... <

lookformeb · « **Reply #6 on:** February 12, 2004, 12:39:00 PM »

Yup. You got a digicam by chance? <

BaDvs3viL · « **Reply #7 on:** February 12, 2004, 03:47:00 PM »

Yeah I do......Im working on that as we speak......post soon <

Lugnut · « **Reply #8 on:** February 12, 2004, 05:00:00 PM »

if you think you can handle soldering a 30 gauge wire to the tsop, the d0 leads to it, i forget what pin number it is, but looking from the front of the xbox at the tsop chip ( right next to lpc holes) the pins farthest away from you 5th from the right should be d0 <

A@ron · « **Reply #9 on:** February 12, 2004, 05:05:00 PM »

I will check with a multimeter here on my end... brb <

A@ron · « **Reply #10 on:** February 12, 2004, 05:13:00 PM »

yup sure enough...

||||||||||||||||||||

||||||||||||||||||||

(LPC) <

Lugnut · « **Reply #11 on:** February 12, 2004, 05:15:00 PM »

:-)

Be careful though thats your last hope if everything else is shot.

This post has been edited by Lugnut: Feb 13 2004, 01:17 AM <

networkBoy · « **Reply #12 on:** February 12, 2004, 07:36:00 PM »

for some example problems on the issue of trace repair you can check out the repairs section on my website, I've got a couple of samples there. Lugnut, I'd be especially interested in your opinion of the extreme damage one. It now boots off the LPC but gives an error7 with the stock hdd and error 9 with a known good 60 gig drive.
-nB <

Lugnut · « **Reply #13 on:** February 12, 2004, 09:06:00 PM »

Man, i dont really know besides the basics which im sure you already went over. no busted pins on the ide connector on the mobo? Hard drive power plug putting out the 5v and 12v ?

<

smokeingit · « **Reply #14 on:** February 13, 2004, 08:33:00 AM »

Author Topic: Another Broke Xbrick Q?.... (Read 289 times)