Print

[ash1471]

QUOTE(b3nnyb0y @ Sep 8 2010, 12:31 PM)

Hi I have a usb spi nand flasher & It doesnt have the pin header for putting into a bootloader mode, Like in the picture on the 1st page.

This is the usb spi nand flasher I have, It has the right pic chip PIC18f2455

http://cgi.ebay.co.u...e=STRK:MEWNX:IT

I have the software installed like it says but its not appearing in the drop down box after I install the driver. If someone knows how I am able to get it into bootloader mode I would be so gratefull.

Thank You

On the picture of the bottom of your nand flasher, If you look to the left there are 2 pads that come off pin 3 on the chip, If you bridge these together it will be in bootloader mode.

ASH

[b3nnyb0y]

Ahhh Thanks mate , Im assuming I just use a wire to bridge and when finished programming remove it? Or can i Juts leave it bridged all tiem time?.

Thanks again, I really appreicate that fast reply. I do ajhve a teensy usb comeing in the post next week but I wanted to crack on now and check out hwow it all works

[ash1471]

QUOTE(b3nnyb0y @ Sep 8 2010, 12:57 PM)

Ahhh Thanks mate , Im assuming I just use a wire to bridge and when finished programming remove it? Or can i Juts leave it bridged all tiem time?.

Thanks again, I really appreicate that fast reply. I do ajhve a teensy usb comeing in the post next week but I wanted to crack on now and check out hwow it all works

However you bridge it it will have to be put back to normal for it to work in the PS3

ASH

[Looouky]

QUOTE(b3nnyb0y @ Sep 8 2010, 05:31 AM)

Hi I have a usb spi nand flasher & It doesnt have the pin header for putting into a bootloader mode, Like in the picture on the 1st page.

This is the usb spi nand flasher I have, It has the right pic chip PIC18f2455

http://cgi.ebay.co.u...e=STRK:MEWNX:IT

I have the software installed like it says but its not appearing in the drop down box after I install the driver. If someone knows how I am able to get it into bootloader mode I would be so gratefull.

Thank You

Yup just like ash said, man that is one interesting pcb layout.

[Looouky]

QUOTE(sxcevo @ Sep 8 2010, 04:24 AM)

cool thanks for the reply they seem good, but i need it within the next few days due to going on holiday sunday. do you know any Uinted Kingdom retailers? cheers

your best to build one then, they are only about 12 pounds to build if that you will need programmer as well, which will be cheap.

Here is what you need to build one:

Tut.
PCB layout image 1.
PCB layout image 2. ensure for the jumper one pin is connected to ground, and one to pin 17.

Programmer Layout.

Ignore everything in the red box, for the programmer schematic.

[ImRickJamesB1tch]

Here are the new files compiled:
http://psx-scene.com...p;postcount=526

For the Diygadget use the 12MHZ....

[b3nnyb0y]

FIXED!!!!!!!!!!!!!!!!!
 
Thank you so very much ash and the others who helped me out with this.

Its all working now I can see backup manger .

I just want to say that if anyone has Modernwarfare then you need to delete it from your saved games on the XMB as the stealthed one uses the mw2 ID, I missed that first and thought I messed up so might help some people.

Thanks ever so much again guys , Im going to make sure I stick around on here now, As i have like 3 posts and been a member a year, Ill try my best to contribute on aything I find thats usefull.

I hate leeches, And I dont want to appear as one, So ill make an effort to help out

[ryaku]

well well, in fact NAND-X from Xecuter has LPC2148 with bootloader, it's possible to program it ?

http://www.nxp.com/d...42_44_46_48.pdf

[chipD]

I used a 18F2550 to make my spi flasher, does anyone know if it will work aswell?

nevermind, found the answer.
Thanks for the link  ImRickJamesB1tch

[PSFanboy]

I purchased this one earlier:
http://ghost2fitter....products_id=298

Luckily I did too as it's now sold out. I must now also jump on the bandwagon of asking whether this will work with PSGroove?

[CardnalSyn]

anyone know where i can purchase the usb spi device from?

**EDIT**

i bought this.
http://www.diygadget...sher-addon.html

will this work?

[DazSH]

http://www.ekitszone.com/Products/5-usb-20-spi-flash-programmer.aspx

Would it work?

also is anyone working on the nand x

[Looouky]

QUOTE(chipD @ Sep 8 2010, 08:14 AM)

I used a 18F2550 to make my spi flasher, does anyone know if it will work aswell?

nevermind, found the answer.
Thanks for the link  ImRickJamesB1tch

yes. you can use the same file.

QUOTE(PSFanboy @ Sep 8 2010, 08:17 AM)

I purchased this one earlier:
http://ghost2fitter....products_id=298

Luckily I did too as it's now sold out. I must now also jump on the bandwagon of asking whether this will work with PSGroove?

yes that will work.

QUOTE(DazSH @ Sep 8 2010, 08:51 AM)

http://www.ekitszone...programmer.aspx

Would it work?

also is anyone working on the nand x

that device is to flash other ics, I don't think that will work. No nand-x support.

QUOTE(CardnalSyn @ Sep 8 2010, 08:40 AM)

anyone know where i can purchase the usb spi device from?

Might be faster and cheaper to build one, like most people did. It really easy and takes about 30mins.

[CardnalSyn]

QUOTE(Looouky @ Sep 8 2010, 10:09 AM)

Might be faster and cheaper to build one, like most people did. It really easy and takes about 30mins.

i ordered this instead...

http://www.diygadget...sher-addon.html

[kryte312]

What about this one? Would it work as well?

http://www.diygadget.com/xbox-360-usb-spi-jtag-utility-bundle.html