Topic: Team Xecuter POGO MO THOIN Homebrew Liteon Probe No Cuts / No Sold (Read 2020 times)

xPlayax · « **Reply #135 on:** February 22, 2011, 01:25:00 PM »

QUOTE

Re-sending Vendor Intro:
.......
Serial flash found with Status 0x52

Extracted drive key failed Verification !

PhatKey extraction failed!

why???

btw... i think its not nessesery that we connect the switch to the 3.3v bun not sure... yet

andy.macht · « **Reply #136 on:** February 22, 2011, 01:29:00 PM »

maybe the preshure of GND-pin is too low.
or you havent the right timing.
or something

3.3V switch is needet if u dont wanna use a capacitor

@suso:
you could cut/solder a switch onto the drive. (if its just one u wanna flash)

Suso14 · « **Reply #137 on:** February 22, 2011, 01:34:00 PM »

QUOTE(andy.macht @ Feb 22 2011, 09:29 PM)

maybe the preshure of GND-pin is too low.
or you havent the right timing.
or something

3.3V switch is needet if u dont wanna use a capacitor

@suso:
you could cut/solder a switch onto the drive. (if its just one u wanna flash)

I don't understand, How i can cut/solder a switch onto the drive? In what part of the drive?

Tnx (sorry for my poor english)

ARY · « **Reply #138 on:** February 22, 2011, 01:39:00 PM »

QUOTE(Suso14 @ Feb 22 2011, 09:16 PM)

Any idea for not cut the 3.3 V cable of my power cable Xbox? It's the only cable that i have, so if i cut the cable i have scare that my xbox don't power on

Tnx (Sorry my poor English)

You can get wire from plug and insert it again, when it's need

Suso14 · « **Reply #139 on:** February 22, 2011, 01:43:00 PM »

QUOTE(ARY @ Feb 22 2011, 09:39 PM)

You can get wire from plug and insert it again, when it's need

Ok, but when i put the cable again it will be place correctly in the plug? (the cable will remain firm and not move? Or need some kind of glue?)

Tnx

ARY · « **Reply #140 on:** February 22, 2011, 02:32:00 PM »

QUOTE(Suso14 @ Feb 22 2011, 09:43 PM)

Ok, but when i put the cable again it will be place correctly in the plug? (the cable will remain firm and not move? Or need some kind of glue?)

Tnx

Yes, sure. Just pull fixing stick and get wire

njmbb8 · « **Reply #141 on:** February 22, 2011, 04:53:00 PM »

can someone show me which cable is 3.3v and which is ground on the dvd power cable?

xPlayax · « **Reply #142 on:** February 22, 2011, 04:58:00 PM »

do my own way... without cap or swich...

Anleitung für ALLE LiteOn Laufwerken

just german... if there are enough people hwo wants to know wat i did plz sent pe pm and i translate it.

njmbb8 · « **Reply #143 on:** February 22, 2011, 08:58:00 PM »

so i get all the way to the wait for 5 seconds step and it says phat key extraction failed. please help

Poopmonkey · « **Reply #144 on:** February 22, 2011, 10:56:00 PM »

Hey guys I'm having a problem with the whole setup of this. I've read over pretty much everything in both the official guide to making these and the posts here and I just cannot get it. I feel like I have done everything correctly but I always get the Phatkey failed error. I am using the CK3 Lite with its probe. Not using the serial cable.

I tried this setup. Cut the Red wire as indicated. Knocked off all surface mount resistors and diodes and then bridge the one place to continue the 3.3v line. The red stuff on the probe is just red liquid insulation tape. Anyways, I tried this setup and I cannot get it to succeed.
IPB Image

Then I saw that the ground wire, aka the black wire does not really attach to anything so mounted a wire like this indicated by the red line. This caused my CK3 Lite to turn off every time I activated the switch, since I basically created a ground fault.
IPB Image

So I removed that new soldered wire and tried a few more times with the first setup. Still did not help. I tried pigphat's directions, I did different timings for the 5 seconds, I feel like I tried it all. Anyone know whats the problem here?

Serious Sam · « **Reply #145 on:** February 22, 2011, 11:31:00 PM »

QUOTE(njmbb8 @ Feb 22 2011, 10:58 PM)

so i get all the way to the wait for 5 seconds step and it says phat key extraction failed. please help

When i get to the "wait for 5 seconds part" shutting off the drive doesn't work for me. What I do is remove the pin, hit yes, switch the 3.3v switch OFF for 5 seconds then ON.

lugi · « **Reply #146 on:** February 23, 2011, 01:47:00 AM »

And here is mine

Have to find a better spear =)

IPB Image

Close up http://img98.imagesh...i/img0058q.jpg/

cypher21 · « **Reply #147 on:** February 23, 2011, 06:13:00 AM »

@poopmonkey,

That won't work,

Why so difficult

For more examples, better look at the xecuter forums in the contest topic

redwhitedream · « **Reply #148 on:** February 23, 2011, 10:36:00 AM »

For all Maximus Xtractor Users !
Who have the SPEAR or VAMPIRE!!
There is no MOD necessary !!!

Spear:
Press Phat Key :yes
Spear to MPX01
Very Quikly OFF/ON The Drive!!
Turn 5sec off and on press okay
Ready!!

With the Vampire there you can do it the same way!
only difference is you must use the pin 101 and press the Button!!!

Buzzcut · « **Reply #149 on:** February 23, 2011, 11:10:00 AM »

Here's mine with a press-to-break switch next to the probe...neatest solution I could come up with.

An easier method I found on another forum is this, it just avoids the pull-out-plug-push-it-back-in power recycle for the non CK3 users.

1) Drive on
2) Click Phat key, click yes
3) Cut 3.3v line (press button), probe MPX01, join 3.3v line (release button)
4) When extraction is complete, instead of removing probe and recycling power just remove probe and cut 3.3v line for a couple of seconds, i.e. I just hold the button down for a couple of secs.
5) Click OK.

EDIT - Just seen that Serious_Sam has this method as well a couple of posts above...can't hurt having it twice though IMO.

Author Topic: Team Xecuter POGO MO THOIN  Homebrew Liteon Probe  No Cuts / No Sold (Read 2020 times)

Author Topic: Team Xecuter POGO MO THOIN Homebrew Liteon Probe No Cuts / No Sold (Read 2020 times)