Topic: Fix E74, Heatgun Method Still Not Work (Read 133 times)

mrghandi · « **on:** December 12, 2009, 01:04:00 AM »

could someone help me with error e74

i already using heatgun n overheat method but it still show e74...
i didn't do xclamp fix, so it's original xclamp from microsoft

could someone help me with my problem

xboxmods2977 · « **Reply #1 on:** December 12, 2009, 01:14:00 AM »

The ORIGINAL XBOX did not have an e74 error. If you are inquiring about the Xbox 360, your post may get more attention in the 360 section.

This post has been edited by xboxmods2977: Dec 12 2009, 09:16 AM

mgeno216 · « **Reply #2 on:** December 12, 2009, 10:59:00 AM »

Reflow the GPU again and if that doesn't work try and reflow the RAM chips. Very rarely the does it lie in the ram, but it is still possible. If that doesn't work you may need a reball. If it comes to that pm and i will give you the name of a good guy.

mrghandi · « **Reply #3 on:** December 14, 2009, 02:08:00 AM »

QUOTE(mgeno216 @ Dec 12 2009, 07:59 PM)

Reflow the GPU again and if that doesn't work try and reflow the RAM chips. Very rarely the does it lie in the ram, but it is still possible. If that doesn't work you may need a reball. If it comes to that pm and i will give you the name of a good guy.

yes, I've done reflow the GPU, RAM CHIP, CHIP ANA several times, but the result is the same, still appear E74 ... I'm Indonesian, I have heatgun like this IPB Image

What may be less hot ..

I have been heating the GPU, RAM, ANA for about 5 minutes with the highest heat level ..... sorry my english not good

under420dog · « **Reply #4 on:** December 14, 2009, 02:57:00 AM »

did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..

This post has been edited by under420dog: Dec 14 2009, 10:57 AM

mrghandi · « **Reply #5 on:** December 14, 2009, 03:46:00 AM »

QUOTE(under420dog @ Dec 14 2009, 11:57 AM)

did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..

Do I need a flux ..

I have 3 times to heat the GPU, ANA, RAM, but the bottom was 1 time I reheat, there is another solution ..??

under420dog · « **Reply #6 on:** December 14, 2009, 04:03:00 AM »

yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....

mrghandi · « **Reply #7 on:** December 15, 2009, 12:49:00 AM »

QUOTE(under420dog @ Dec 14 2009, 01:03 PM)

yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....

thank's for before...
after reflow the gpu, now my xbox is showing 0102, i have using the methode to fix the 0102 problem but it still didn't work!
what should i do next??

under420dog · « **Reply #8 on:** December 15, 2009, 05:12:00 AM »

heat it back up....what's the temps that station puts out?

mrghandi · « **Reply #9 on:** December 15, 2009, 07:11:00 AM »

QUOTE(under420dog @ Dec 15 2009, 02:12 PM)

heat it back up....what's the temps that station puts out?

it's 300c max

Author Topic: Fix E74, Heatgun Method Still Not Work (Read 133 times)