Print

[Exobex]

QUOTE(heartshacker @ Oct 23 2011, 07:52 PM)

I am having HP DVD Writer 1260r MH22 and planning to cross flash  with iHAS124B or iHAS524B? Anybody have any idea that will it work? If it does not work is there any way I can revert back to my original firmware.

Hope there will be a way to do so. Also expecting there will be some list of cross flashing compatibility list of DVD.

Save a copy of your drive's EEPROM and firmware before you crossflash. Also ensure that the drive has the correct chipset, pop the lid off if necessary.

[cdsmally]

QUOTE(bucky006 @ Oct 23 2011, 03:38 PM)

Well I was getting everything fail at 50% verification, using iHAS124B.

Crossflashed to iHAS524B still failing at 50%.

Went into Drive advanced setting on imageburn and changed ForceHyperTuning on, OnlineHyperTuning on and Smartburn off, and have no idea what these settings do!!!

Anyway now my discs are burning and verifying 100%, No idea if its because I changed these setting or not, but I'm now happy.

Using AonePLUS DL's, very cheap.

Trying these settings now with iHAS324B but i am only burning at 0.6% now for some reaseon. Gonna take 3hrs to burn this image.

Guess i'll just have to wait and see (i'm gonna try some different settings tomorrow)

[grartie]

What speed are you burning the aone discs at ? and have you enabled opc.
burnt 2 aone coasters earlier .

[heartshacker]

QUOTE(Exobex @ Oct 24 2011, 12:49 AM)

Save a copy of your drive's EEPROM and firmware before you crossflash. Also ensure that the drive has the correct chipset, pop the lid off if necessary.

Thanks for your reply. I was reading few post and came to know that crossflash works. That's why I planned to do so. Still trying to figure out how to back up drive's EEPROM and firmware. Also not sure what do u mean by "drive has the correct chipset, pop the lid off if necessary"

I got EEPROM_Utility_6.2.0 this and when I try to backup my eeprom I am getting "Error reading EEPROM from drive!" Do I need to change any settings or my drive is not comparable for crossflashing.

[bucky006]

QUOTE(grartie @ Oct 23 2011, 09:23 PM)

What speed are you burning the aone discs at ? and have you enabled opc.
burnt 2 aone coasters earlier .

The slowest I can burn is x4,and since changing my setting everything is burning ok.

Also installing to harddrive with no problems now, we're failing at around 51% before.

I have No OPC selected.

[grartie]

Thanks for the reply  BUCKY006   will try a burn now.

[bucky006]

Switched Smartburn back on and still getting a good burn, must be todo with hypertuning.

Either way I don't care, its working which is all i'm worried about.  

Hope its working for others  

[pmaster]

I was successful in burning an xgd3 iso with my new iHAS124B w/ MAX Burner FW and using a verbatim MKM003. It verified 100% in ImgBurn.

Today i tried to burn an XGD3 iso onto one of my Amazon Basics disks, and well, it burned and verified 100% successful just like the verbatim.

What do you guys make of this?  It would be nice if i could use up my 40 or so extra Amazon Basics disks if they work with XGD3.  (Disk ID:  UMEDISC-DL1-64)

edit: both disks were burned at 4x with OPC turned On.

[dreday78]

QUOTE(pmaster @ Oct 23 2011, 02:46 PM)

I was successful in burning an xgd3 iso with my new iHAS124B w/ MAX Burner FW and using a verbatim MKM003. It verified 100% in ImgBurn.

Today i tried to burn an XGD3 iso onto one of my Amazon Basics disks, and well, it burned and verified 100% successful just like the verbatim.

What do you guys make of this?  It would be nice if i could use up my 40 or so extra Amazon Basics disks if they work with XGD3.  (Disk ID:  UMEDISC-DL1-64)

edit: both disks were burned at 4x with OPC turned On.

As long as it verifies you should be good.  I've burned several games now on Windata disc at 4x, all verified.  I aslo have OPC turned on, along with hypertuning and smartburning.

[vegasmtv]

Anyone know if LiteOn IHAS124-19 will work when connected to the same SATA card i have in my pc which i use for my CK3. I ask as i had to uninstall the drivers i think, or something like that, to get the CK3 pro to be able to flash.

[nogooder]

No joy so far for me...

iHAS124B + MKM003 @ 4x w/ OPC on - Fail Verify at 50%
iHAS124B + MKM003 @ 2.4x w/ OPC on - Fail Verify at 50%
iHAS124B + RICOHJPNSD0 @ 4x w/OPC on - Fail at finalizing disc, ran out of calibration space.

iHAS124B flashed properly - check
Using proper media - check

Trying at 2.4x with OPC off. If that doesn't work I'll try turning off some other settings as Bucky006 did.

Fingers crossed...

[bigballs5]

QUOTE(vegasmtv @ Oct 23 2011, 08:52 PM)

Anyone know if LiteOn IHAS124-19 will work when connected to the same SATA card i have in my pc which i use for my CK3. I ask as i had to uninstall the drivers i think, or something like that, to get the CK3 pro to be able to flash.

I used my ck3 to flash my drive IHAS124-19 via my laptoptop. The laptop installed the drivers for the drive and then I flashed it. So if you have flashed it re-install it and it should work.

[decapitado]

QUOTE(nogooder @ Oct 23 2011, 08:57 PM)

Trying at 2.4x with OPC off.

That way will work

[grartie]

  THANKS BUCKY006, used your settings and have just successfully burnt and verified using aone plus DL.

[bucky006]

QUOTE(grartie @ Oct 23 2011, 10:21 PM)

THANKS BUCKY006, used your settings and have just successfully burnt and verified using aone plus DL.

Cool