Topic: Drilling The 0225 (Read 165 times)

jaredanand · « **on:** October 16, 2011, 08:16:00 PM »

Ok guys, so after a long duration of carefully dremelling epoxy off the mxic, i have come to slight differences in coordinates of where to drill..

Below are 2 "draw-ups" of where I should drill. But they are awfully close to eachother. So my question is, will drilling in that general area cut the trace? Or is it completely off?

*These are pics from my drive*

1st Picture
(IMG:http://img190.imageshack.us/img190/4430/20073687.jpg)

2nd Picture
(IMG:http://img820.imageshack.us/img820/3752/41837120.jpg)

Help is very much appreciated

This post has been edited by jaredanand: Oct 17 2011, 03:18 AM

Dark Mod · « **Reply #1 on:** October 16, 2011, 09:40:00 PM »

Once its 5 legs vertical and 8 legs horizontal, you in the safe zone, would recommend to use the soldering iron if you don't wanna screw up a drive

jaredanand · « **Reply #2 on:** October 16, 2011, 09:45:00 PM »

Well ive got a precision hand, a dremel, and a .5mm bit so I think im in the safe zone any other way (IMG:style_emoticons/default/tongue.gif)

Edit: Ok, I have measured the distance between the two intercepts, it turns out to be 0.4mm. Will I be able to hit the WP if i drill in between the two intercepts?

This post has been edited by jaredanand: Oct 17 2011, 05:08 AM

jaredanand · « **Reply #3 on:** October 17, 2011, 12:46:00 AM »

Edit 2: I plan on drilling at the mark indicated on tuesday (I get my CK3 on tuesday). Let me know if the hole size is too big or off target...

(IMG:http://img717.imageshack.us/img717/218/25211461.jpg)

All help is very much appreciated.

lenselijertje · « **Reply #4 on:** October 17, 2011, 02:08:00 AM »

this looks good, get the right dremel tip and carefully drill your way to the unlock

totoz · « **Reply #5 on:** October 17, 2011, 07:32:00 AM »

follow your second picture

jaredanand · « **Reply #6 on:** October 17, 2011, 04:40:00 PM »

From what I measured from the high res pics, they are both pretty accurate, its just a matter of drilling it right.

Just a question though, are the WP wires far enough away from other wires that I can drill in the middle of both measured intersects?

Edit: Forgot to mention the MTK is Winbond not MXIC

This post has been edited by jaredanand: Oct 18 2011, 12:26 AM

jaredanand · « **Reply #7 on:** October 29, 2011, 01:45:00 AM »

Alright, well ive just figured out that my drive wont vendor intro with my nForce chipset... Is there any alternatives to get it into vendor mode without the x360usb pro? And can you proceed with the unlock with the method?

jaredanand · « **Reply #8 on:** November 15, 2011, 06:42:00 PM »

Ok, so the kamikaze went beautifully, flashed LTPlus 2.0, now whenever I go to play a backup, I get "This Disc is not supported." Although the game does show up in dash. I made a backup of Modern Warfare 3, with an 0800 drive, but havent checked the iso with abgx yet as they dont support XGD3 backups yet.

TL;DR - Flashed my 0225 with LTPlus 2.0, getting an error "This disc is not supported."

zyo · « **Reply #9 on:** November 16, 2011, 01:42:00 AM »

QUOTE(jaredanand @ Nov 16 2011, 02:42 AM)

Ok, so the kamikaze went beautifully, flashed LTPlus 2.0, now whenever I go to play a backup, I get "This Disc is not supported." Although the game does show up in dash. I made a backup of Modern Warfare 3, with an 0800 drive, but havent checked the iso with abgx yet as they dont support XGD3 backups yet.

TL;DR - Flashed my 0225 with LTPlus 2.0, getting an error "This disc is not supported."

well its actually very easy to tell if the drive plays original mw3 then you screw up the backup otherwise you screw up the drive.

dougiegillam · « **Reply #10 on:** November 16, 2011, 09:07:00 AM »

QUOTE(jaredanand @ Nov 16 2011, 03:42 AM)

Ok, so the kamikaze went beautifully, flashed LTPlus 2.0, now whenever I go to play a backup, I get "This Disc is not supported." Although the game does show up in dash. I made a backup of Modern Warfare 3, with an 0800 drive, but havent checked the iso with abgx yet as they dont support XGD3 backups yet.

TL;DR - Flashed my 0225 with LTPlus 2.0, getting an error "This disc is not supported."

Did you follow the Jungleflasher Guide when writing the F/W? Take the drive back out and follow the guide in the jungleflasher tutorial i.e use the part of the guide that refers to replacement tx board (page 211 of tut 1.4.4) when writing the f/w closing the cut outro the drive etc. Its very important you follow it word for word.

jaredanand · « **Reply #11 on:** November 16, 2011, 02:38:00 PM »

Turns out the drive is fine, it plays backups with a LB of 1913760 just fine. It must be something i did wrong while backing up the game. BTW im using an iHAS 124 flashed with burner max to burn the backups...

Is there a good tut on how to properly back up and burn XGD3 games?

crowdogx · « **Reply #12 on:** November 16, 2011, 06:56:00 PM »

http://team-xecuter....ead.php?t=71801

did you use the correct dae.bin file when backing up you original game
otherwise the xgd3 game wont work
cheers

jaredanand · « **Reply #13 on:** November 16, 2011, 07:27:00 PM »

Just got an update from MW3... Doesnt look so good. All backups are not working, both XGD2, and XGD3.

Word has it that everyone who has installed the update is unable to boot these games either...

DO NOT UPDATE!!!

http://www.xbox360is...w3-t510556.html

Must be signed in to view the topid, definitely worth the read. Please do so

Author Topic: Drilling The 0225 (Read 165 times)