Topic: Geremia MT1335 Macronix and Winbond (DG-16D4S LiteOn) Unlocking (Read 691 times)

Xbox-Scene · « **on:** August 02, 2011, 11:01:00 PM »

Geremia MT1335 Macronix and Winbond (DG-16D4S LiteOn) Unlocking
Posted by XanTium | August 3 01:01 EST | News Category: Xbox360

From xboxhacker.org:

Quote

Spent some time with Maximus over the mx and wb flashes, while the mx is a piece of cake, the WB is a bitch.
There were at least 3 solutions for WB, some more risky, this is less risky one, even if it's not noob friendly.
It's even not so much techical in comparison to the others one that had few success rate, or against the ones that had lot of effort and got no result.
There are also other possibilities for a software only way, but it's like going blindly searching for a fantomatic "winbond manufacturer mode" (how the hell do they write the serial numb in there? there must be a way), but actually i'm getting lazy.

Btw, since fw out here have some small differences, prior to go erasing and writing, would be usefull to have fulldump (0225,0225u,0401,xxxx+) ... if you have an app/device that can do it o.c.

As usual, use at your own risk, i don't care. Hate it or love it, i don't care.
Special thanks to Maximus for cooperating and for supplying test ICs.

News-Source/Download: xboxhacker.org

PaddyPat · « **Reply #1 on:** August 03, 2011, 12:15:00 AM »

where do these guys come up with this shit? amazing

ichigoxxx · « **Reply #2 on:** August 03, 2011, 12:18:00 AM »

Great Video.

letsmod · « **Reply #3 on:** August 03, 2011, 12:27:00 AM »

angrykid · « **Reply #4 on:** August 03, 2011, 12:49:00 AM »

worst case scenario I guess you can always go replacement pcb!
very cool trick... time to invest in a dremel tool

deilzfcjk · « **Reply #5 on:** August 03, 2011, 02:46:00 AM »

you should have a dremel already if you're into modding. You have been here long enough AngryKid.

but it's awesome!!!

warnos16v · « **Reply #6 on:** August 03, 2011, 04:23:00 AM »

Have just done 5 Winbonds and an MX (diff resistor)that would not work with russian.. this is awsome.. props to Geremia... this would have taken ages to figure out..

This is totally a not for noobs kind of mod... if this is ur 1st mod take it somewhere to get modded.

Can see allot of ppl stuffing chips/boards up trying this one..lol

This post has been edited by warnos16v: Aug 3 2011, 11:24 AM

Pseudo99 · « **Reply #7 on:** August 03, 2011, 05:28:00 AM »

The moment I understood exactly what was going on....I got the giggles...literally...this shit is so amazing. Time to start dremeling some chips (IMG:style_emoticons/default/smile.gif)

iateshaggy · « **Reply #8 on:** August 03, 2011, 05:36:00 AM »

smart thinking the way he probes the drill so he knows right when the magic happens.

danthaman673 · « **Reply #9 on:** August 03, 2011, 06:04:00 AM »

This is fricking awesome!

THANX AGAIN GERAMIA! For being the one to provide the solution! YOU ARE A BLOODY LEGEND! First as always! 'Russian Unlock' Now re-branded : 'Geramia SPI Unlock Solution' GSUS for short ;-)

This is the most not-for-noobs-mods YET! The award goes to ...
It's an awesome trick! make sure you use the right tools, or you might find a spinning metal drill-bit gives you more than you asked for!
Getting the right pos when you look at the overlay (and know what's involved) , well .... let's just say there's not much in it! I shudder to think of the 3 more solutions that were more risky ;-)

QUOTE(angrykid @ Aug 3 2011, 04:19 PM)

worst case scenario I guess you can always go replacement pcb!
very cool trick... time to invest in a dremel tool

All the PCB's are sold out! Sooo Might be a good idea to make sure you have one at the ready!
I will now need to try to order a lot of 'TX pro unlock chip/kits' Pity I can't find anyone who has any :-(

Truly inspired/Dan

dank4life · « **Reply #10 on:** August 03, 2011, 06:34:00 AM »

you guys are truely appreciated. Geremia, you are a Jedi master - guardian of peace and justice. Max, you know I love you, man. Words cant express how big this it. Thank you guys

boflc · « **Reply #11 on:** August 03, 2011, 08:34:00 AM »

wow. plain and simply. a spark.

Skevus · « **Reply #12 on:** August 03, 2011, 08:46:00 AM »

QUOTE(danthaman673 @ Aug 3 2011, 02:04 PM)

This is fricking awesome!

THANX AGAIN GERAMIA! For being the one to provide the solution! YOU ARE A BLOODY LEGEND! First as always! 'Russian Unlock' Now re-branded : 'Geramia SPI Unlock Solution' GSUS for short ;-)

This is the most not-for-noobs-mods YET! The award goes to ...
It's an awesome trick! make sure you use the right tools, or you might find a spinning metal drill-bit gives you more than you asked for!
Getting the right pos when you look at the overlay (and know what's involved) , well .... let's just say there's not much in it! I shudder to think of the 3 more solutions that were more risky ;-)
All the PCB's are sold out! Sooo Might be a good idea to make sure you have one at the ready!
I will now need to try to order a lot of 'TX pro unlock chip/kits' Pity I can't find anyone who has any :-(
Truly inspired/Dan

I Live in sweden and I found some here:

http://shop01media.com/search.asp?search=D...search=DG-16D4S

They sell from Sweden and Poland, quite sure they sell to anyone in EU...

This post has been edited by Skevus: Aug 3 2011, 03:52 PM

Dark Mod · « **Reply #13 on:** August 03, 2011, 10:26:00 AM »

and I thought moddin a D2C wii with the D2Ckey was hard, this takes the cake right here

smuddge37 · « **Reply #14 on:** August 03, 2011, 10:51:00 AM »

yes this is going to result in a lot of damaged boards.....

Author Topic: Geremia MT1335 Macronix and Winbond (DG-16D4S LiteOn) Unlocking (Read 691 times)