Topic: Liteon 74850c Mra Hack Problems (Read 83 times)

dave11674 · « **on:** December 30, 2010, 01:21:00 PM »

hi

i have a 74850c drive here
it has ix LT 1.1 on it
doing the drive half open trick would not do squat for this drive to get dummy from ix.

so i believe i have to do the MRA hack as this is what i had to do with a previous drive same model.

ok that other one went just fine.

this one is givign me all 777777777777777777 as the dvd key.
no way am i writing the data back like that heheh

ok so upon removing my 1.5 switch i clean solder points up and am noticing im getting a short across a couple of points, on a fresh board from the same drive this short is not presant.

can any1 help me here as the drive clearly aint dumping the key right so i cant proceed further.
the 2 arrows in the pic are the points that are shorting.
and as you can see there is clearly no solder bridging across the 2 tracks
(IMG:http://i27.photobucket.com/albums/c188/dave11674/IMG_0714-Copy.jpg)

thanks for any help and pointers here guys

Takashi · « **Reply #1 on:** December 30, 2010, 01:50:00 PM »

Well, you might want to ditch the lt switch, it's junk.
Use the Boxxdr method.

dave11674 · « **Reply #2 on:** December 30, 2010, 01:57:00 PM »

basically same thing just diff hardware
same results

edit
same reults with the resistor Boxxdr method

still dont explain why teh 2 points are shorted out tho
when a fresh new drive they are not

dave

iateshaggy · « **Reply #3 on:** December 30, 2010, 04:45:00 PM »

take a picture of your drive. obviously there is a short and all you have to do is look at it to tell it is there, then remove that solder. if you have removed any obvious shorts and still have one, then you can toss the whole thing in the trash.

dave11674 · « **Reply #4 on:** December 30, 2010, 04:58:00 PM »

QUOTE(iateshaggy @ Dec 30 2010, 11:45 PM)

take a picture of your drive. obviously there is a short and all you have to do is look at it to tell it is there, then remove that solder. if you have removed any obvious shorts and still have one, then you can toss the whole thing in the trash.

erm do u not see the pic above !?!?!?

why throw it in the bin ?!?!?

its somethign simple i know this.

anyone else with something better to contribute ?

dave

Takashi · « **Reply #5 on:** December 30, 2010, 06:22:00 PM »

It's pretty hard to recover from shorts, majority of the time there's nothing you can do except
just learn better electronics skills for future mods.
One of the few ppl on this forum that even has a chance of helping you is syntaxerror329

This post has been edited by Takashi: Dec 31 2010, 02:22 AM

dave11674 · « **Reply #6 on:** December 30, 2010, 07:16:00 PM »

QUOTE(Takashi @ Dec 31 2010, 01:22 AM)

nothing you can do except
just learn better electronics skills for future mods.

hheheheh

ive been doing electronics engineering for the past 20 years mate
my soldering skills and electronic skills are 100 to 1 at teh best of times (IMG:style_emoticons/default/smile.gif)

dave

Takashi · « **Reply #7 on:** December 30, 2010, 07:29:00 PM »

Don't take it the wrong way, but the pics don't reflect that lol

totoz · « **Reply #8 on:** December 31, 2010, 03:16:00 AM »

there's a big difference: see boxxdr jpeg and your pic...

With traces cut and power from ck3 (or 360) voltage at pin101 is 2,15v
and if u look the second (vertical) cut it's 2,15v on the left and 1,30v on the right

check these values

when u repair traces everything 3,3v

Clean the pcb with braid and use good flux, it helps a lot.

This post has been edited by totoz: Dec 31 2010, 11:17 AM

dave11674 · « **Reply #9 on:** December 31, 2010, 06:53:00 AM »

the board is cleaned with braid and no need for flux.

there is no shorts across my solder points on this board.

takashi
lets see some of your pics then big shot

Takashi · « **Reply #10 on:** February 02, 2020, 05:43:00 PM »

QUOTE(dave11674 @ Dec 31 2010, 08:53 AM)

takashi
lets see some of your pics then big shot

(IMG:style_emoticons/default/smile.gif) probably my messiest work
74850C pic

dave11674 · « **Reply #11 on:** February 03, 2020, 09:58:00 AM »

QUOTE(Takashi @ Jan 1 2011, 12:43 AM)

(IMG:style_emoticons/default/smile.gif) probably my messiest work
74850C pic

hahah u trying to say your work is better than mine and poist your messiest pic

lol

anyways back to topic.

totoz
the 2 vertical lines i do just to make it easier that trying to cut out the actual 101 point
i put a jump wire across the left and right contacts then so all is good.

dave

also looking at the dump there is lots of data in ther elike its fully dumping it.

dave

iateshaggy · « **Reply #12 on:** February 03, 2020, 12:40:00 PM »

he's not the one whose modded drive isn't working.

Takashi · « **Reply #13 on:** February 03, 2020, 01:04:00 PM »

it's all i had a pic of, I don't have a need to snap pics of my work, because i have a 100% success rate.

Tron[ADS] · « **Reply #14 on:** February 03, 2020, 03:41:00 PM »

QUOTE(dave11674 @ Dec 30 2010, 10:21 PM)

i have a 74850c drive here
it has ix LT 1.1 on it
doing the drive half open trick would not do squat for this drive to get dummy from ix.

I'm a bit puzzled as to why you are wanting to do anything with this drive if it already has LT 1.1 on it.

Author Topic: Liteon 74850c Mra Hack Problems (Read 83 times)