Topic: Boxxdr Method For Complete Lite-on Firmware Dump. (Read 3636 times)

jim168 · « **Reply #615 on:** February 02, 2020, 07:04:00 PM »

Ty for the nice tut, but i got a problem, after i dumped the dummy.bin, i rejoined the cut traces together, however now xbox mid LED is constantly flashing, and the drive isnt getting detected with jungleflasher when i tried to flash it. (mind i also add that after i read the OFW, i spoofed it as a hitachi with ix161-934 fix.bin)

Sawks · « **Reply #616 on:** November 20, 2010, 08:03:00 AM »

I have a liteon 93450c drive i had some minor dramas getting the drive to be recognised in JF but finally i got it to read after discovering a bit of solder was mtouching the board and earthing. I got to read the drive and save the firmware when i tried to write the ixtreme lt 934 i got an error when it checked
i was told to resolder the traces and erase liteon wit JF
I resoldered the traces but now my drive ejects fast and seems to smell from the eject motor or something
when i Tried to erase i got an 0xF2 device intro failed what do i do or what have i done it is a friends xbox and i hope its ok
I tried to power on the xbox and connect to tv boxstill works but i cant eject drive have i bricked the drive?

Sawks · « **Reply #617 on:** November 20, 2010, 06:07:00 PM »

QUOTE(Sawks @ Nov 20 2010, 04:03 PM)

I have a liteon 93450c drive i had some minor dramas getting the drive to be recognised in JF but finally i got it to read after discovering a bit of solder was touching the board and earthing. I got to read the drive and save the firmware when i tried to write the ixtreme lt 934 i got an error when it checked
i was told to resolder the traces and erase liteon wit JF
I resoldered the traces but now my drive ejects fast and seems to smell from the eject motor or something
when i Tried to erase i got an 0xF2 device intro failed what do i do or what have i done it is a friends xbox and i hope its ok
I tried to power on the xbox and connect to tv boxstill works but i cant eject drive have i bricked the drive?

I have resoldered all traces and i have checked with a mutimeter all good now I get a 0x7F
i put power cable partly in upside down and heard a click now i think its gone

Andy_K · « **Reply #618 on:** November 23, 2010, 02:23:00 PM »

Quick one...

I've done a full dump of my 93450c successfully... unfortunately i then screwed the drive repairing the traces. I have since bought an 83450c v1 drive and am wishing to flash with the newly released LT+. However, would anyone be able to tell me which version of firmware I use, i.e. 83450c (because that's the drive version) or 93450c (because that's what it will be replacing in the brand new Elite?

Cheers Guys!!!

Buzzcut · « **Reply #619 on:** November 23, 2010, 02:46:00 PM »

QUOTE(Andy_K @ Nov 23 2010, 09:23 PM)

which version of firmware I use?

The same as your original box. All Liteon boards are the same apart from the firmware so you'll be fine flashing between versions. Just ignore any warnings when you overwrite with the new firmware.

ruben182 · « **Reply #620 on:** November 27, 2010, 09:43:00 AM »

I have flashed a liteon 93450c in the past without problem using this method.
I used it with 22ohm.

But today I got 2 liteon 74850c drives with LT and the people lost their key.
I understand I can't read it with the spear, only MRA.
So I did the same thing. Cut the traces, checked it with a multimeter.
Made the necessary bridges and placed the switch.

Jungleflasher recognizes the drive as a liteon.
But when I do intro I ALWAYS get the 0x51 (or 0x52) status.
I tried all the different timings, the exact same steps that are described here, but always the same status.

I can flash Hitachi, Samsung, BenQ and LiteOn without problems on the same pc.
When I do a liteon erase on a drive where I already have the key, I receive a correct 0x72 status.
I tried using 20ohm and 18ohm.
I even used the Xecuter LT switch by wiring them to the correct point.
Still 0x51 !!

The VIA drivers are installed, deleted and disabled.
Using Windows 7 32bit.

If someone is interested I can take a picture of the connections, but I'm 100% sure everything is connected correct. I have checked it, double checked it, triple checked it,...
The drive also works perfect when I reconnect the broken traces.

Other ideas?

willthiswork89 · « **Reply #621 on:** November 28, 2010, 03:26:00 PM »

Hye guys, i ripped a trace off while desoldering and wanted to know if there is somewhere i can bridge it to. just to the cut, the other side is intact. IPB Image

Demonsc · « **Reply #622 on:** December 01, 2010, 08:20:00 PM »

Can you post all the products u used to do this method for example

The tools used to make the board shinier
The switch used
etc...

And i site i can order all the stuff at

Takashi · « **Reply #623 on:** December 01, 2010, 08:31:00 PM »

All on the first page.
http://forums.xbox-s...howtopic=698256
as far as sites, google works best

totoz · « **Reply #624 on:** December 02, 2010, 06:22:00 AM »

QUOTE(ruben182 @ Nov 27 2010, 05:43 PM)

Jungleflasher recognizes the drive as a liteon.
But when I do intro I ALWAYS get the 0x51 (or 0x52) status.
I tried all the different timings, the exact same steps that are described here, but always the same status.

Other ideas?

had the same problem, liteon with LT without the key (and also with the key)
solution: when it's time to remove power from liteon, don't use the on/off on ck3, but remove manually the power from the BACK of the drive and quickly re-plug the cable (thanks djnaff on efnet)

This post has been edited by totoz: Dec 2 2010, 02:37 PM

offtopic · « **Reply #625 on:** December 09, 2010, 08:45:00 AM »

Hello

I have question about reflash to iX LT+ liteon 93450c a0a2 with bricked pad 101(repaired - work ok). What i must solder/desolder?? I have probe2.

swq · « **Reply #626 on:** December 09, 2010, 09:49:00 AM »

Hi9 guys... I'm nt sure why i can't get to 0x72.. intro failed!! why!! I'm i doin something wrong..

Uploaded with ImageShack.us

Takashi · « **Reply #627 on:** December 09, 2010, 01:23:00 PM »

QUOTE(offtopic @ Dec 9 2010, 10:45 AM)

Hello

I have question about reflash to iX LT+ liteon 93450c a0a2 with bricked pad 101(repaired - work ok).

Wow~!
These pics are going to my collection of roflz!
Seriously though, that's some of the scariest work i've seen so far,
I don't even know what to say!

There's no need to resolder anything if you have the old dumps,
just erase then flash new cfw.

totoz · « **Reply #628 on:** December 09, 2010, 02:47:00 PM »

QUOTE(bucky006 @ Dec 6 2010, 03:19 PM)

Hi,
Or can I just flash my drive once I've retreived my key, and then remove and repair the fix.
Regards

yes u can

xmstree · « **Reply #629 on:** December 11, 2010, 10:07:00 PM »

edit: removed.

Does anyone know why this method isn't in the jungle flasher tutorial? Only the more difficult original MRA hack is documented. This boxxdr method has been known for a long time now.

Has anyone tried this method without using solder? In theory you could just electrical tape the wires to the traces. Maybe that doesn't provide a very reliable connection - however it only needs to last a few minutes. I guess the repair job should be done with solder though.

Author Topic: Boxxdr Method For Complete Lite-on Firmware Dump. (Read 3636 times)