Topic: iXtreme v1.6 for Liteon 83V2 and 93450 - Better Dumping Method (Read 1099 times)

xboxer360 · « **Reply #60 on:** December 09, 2009, 12:48:00 AM »

i had to eventually step down to an 11ohm resistor to get that drive to dump.. wow....

andifx · « **Reply #61 on:** December 09, 2009, 12:54:00 AM »

QUOTE(green360 @ Dec 5 2009, 02:01 PM)

hye I read that the solution to this drives wich still give a 52 statut is to use a smaller resistor like 20ohms or 18, 16 ohms & tray again
good luck

ok thanks, i just tried it, its give me status x72... but there's another anomali... in flash chip properties give Manufacturer ID: 0x00
Device ID: 0x00
The Read Flash Button is available, but of couse it can't dump the key....
is there any other solution ??

thank you

xboxer360 · « **Reply #62 on:** December 09, 2009, 12:59:00 AM »

just press intro again andifx and it should show up the chip ID, then once read it will say no key but you need to open it up in the TARGET firmware on jungleflasher.

wang_chung · « **Reply #63 on:** December 09, 2009, 01:18:00 AM »

i got the key (finally), verified with 3 dumps, and now every time i save the original from the target field and try to open it under source, and it won't go (this is not a valid source f/w file). in fact, nothing will open under the source field (ix1.61 template, my dump, or my dump that was saved from the target). so i manually entered in the barcode and the key, but from what the i read, it doesn't work. before i waste another hour, any suggestions?

mine is a 93450 if it matters

This post has been edited by wang_chung: Dec 9 2009, 09:19 AM

xboxer360 · « **Reply #64 on:** December 09, 2009, 01:20:00 AM »

dude you open it in target, then right click the window surrounding it, save dummy.bin and then reopen in sourch

dragoscojan · « **Reply #65 on:** December 09, 2009, 05:45:00 AM »

QUOTE(xboxer360 @ Dec 9 2009, 08:18 AM)

i've done over 10 of these now, but i'm stuck with one wierd one, gives me status 80 then 52, no matter what i try, it's like the spi is staying powered up, I have lifted both 3.3v pins and the 1.8, cut traces below, plug it in xbox and it still runs games.... i'm stumped.

if anyone wants a solderless way, no trace cuts, no pin removal, just bridge 100 and 101 on intro, once it detects, unbridge read and voila, just use a pin or the tip of your multimeter, have done a few this way and none have been damaged.

which one is pad 100?

wiebel · « **Reply #66 on:** December 09, 2009, 06:12:00 AM »

QUOTE(xboxer360 @ Dec 9 2009, 07:18 AM)

i've done over 10 of these now, but i'm stuck with one wierd one, gives me status 80 then 52, no matter what i try, it's like the spi is staying powered up, I have lifted both 3.3v pins and the 1.8, cut traces below, plug it in xbox and it still runs games.... i'm stumped.

if anyone wants a solderless way, no trace cuts, no pin removal, just bridge 100 and 101 on intro, once it detects, unbridge read and voila, just use a pin or the tip of your multimeter, have done a few this way and none have been damaged.

Interested in this method as well... Can anyone confirm this method is actually working, like for all liteon models?

pastortom · « **Reply #67 on:** December 09, 2009, 08:02:00 AM »

QUOTE(wiebel @ Dec 9 2009, 03:12 PM)

Interested in this method as well... Can anyone confirm this method is actually working, like for all liteon models?

Looks like my videoguide got kinda lost earlier in this thread

Maybe i should make a seperated thread for it, humms..

I can confirm this works for 7485 and 9345 (93450 c).. and Im pretty sure it works on a 8385

wiebel · « **Reply #68 on:** December 09, 2009, 08:43:00 AM »

Well i've watched your youtube vid. However xboxer360 seems to suggest we would only need to short that two pads. Looks to me kinda like the days of 73450 where you just bridge r107 (i believe it was) and some other pad with a paperclip.

wang_chung · « **Reply #69 on:** December 09, 2009, 09:40:00 AM »

right click! all i needed, damn. thanks xboxer360.

ok, did all that, but the 93450 ix firmware shows up as 83850, and i get the error "cross spoofing between versions of liteon is not supported". now i can manually enter the info, is that what everyone else is doing for the 93450? cause i read some other guys saying it doesn't work?

This post has been edited by wang_chung: Dec 9 2009, 05:54 PM

Takashi · « **Reply #70 on:** December 09, 2009, 09:42:00 AM »

Download the lite-on templates from xbins, and open the 9 series template as your target firmware.

iglitare · « **Reply #71 on:** December 09, 2009, 09:45:00 AM »

QUOTE(wang_chung @ Dec 9 2009, 05:40 PM)

right click! all i needed, damn. thanks xboxer360.

ok, did all that, but the 93450 ix firmware shows up as 83850, and i get the error "cross spoofing between versions of liteon is not supported". now i can manually enter the info, is that what everyone else is doing for the 93450?

excactly.

just enter your key and serial data

xboxchan · « **Reply #72 on:** December 09, 2009, 10:06:00 AM »

what leg on the chip is p101? the trace for p101 is gone on the borad I'm doing.

Thanks,

tonny_online · « **Reply #73 on:** December 09, 2009, 10:08:00 AM »

Well folks, already able to extract the key by Dosflash32, but when you try to open there in JungleFlash file appears as invalid.

My drive is the 83850c V2 ...

What should I do next?

ccfman2004 · « **Reply #74 on:** December 09, 2009, 10:17:00 AM »

QUOTE(tonny_online @ Dec 9 2009, 06:08 PM)

Well folks, already able to extract the key by Dosflash32, but when you try to open there in JungleFlash file appears as invalid.

My drive is the 83850c V2 ...

What should I do next?

Did you open it as TARGET? You can't open it as source.

Author Topic: iXtreme v1.6 for Liteon 83V2 and 93450 - Better Dumping Method (Read 1099 times)