Print

[Keezie]

i've soldered enough to be familiar and comfortable with this process, but i have a couple of questions

1. how exactly do i "resolder" the cut traces? do i need to scratch em down and connect a wire?

2. where exactly do i put the switch? the dotted line and a 1 and 2 aren't really doing much for me

thanks!

[yamanik]

Hi everyone ,

I got all soldered perfectly no mess.
As i use to do a lot of satelllite receiver back 10 years ago...( Jtags and epprom removal )

I think i lost patience...

Please anyone in Montreal are or Laval area  can PM , i`m willing to pay to get it flashed pleas


XBOX 360 elite
Liteon 93450c modded with the 22ohmz and 3.3V

Please PM waiting for you help Offer 40 $

[chorizo1]

QUOTE(ccfman2004 @ Dec 6 2009, 02:12 AM)

Anyone have the original firmware dump for the Lite-On 83xxxV1 as I would like to go back to stock.

DO NOT ASK FOR FIRMWARE HERE. PERIOD.

this isn't even a new rule, this has always been the case here.

This post has been edited by chorizo1: Dec 6 2009, 06:37 PM

[tonny_online]

I'm having problems running Dosflash, it is only one giving this error message "No ATAPI devices present!"

Has anyone had this problem?

Can you help?

QUOTE(Takashi @ Dec 2 2009, 01:26 AM)

Works Beautifully!
THANK YOU!!!!!

I'm having problems running Dosflash, it is only one giving this error message "No ATAPI devices present!"

Can you help me?

[pastortom]

Tonny_Online.. Are you using a dosflash configured for your VIA sata chipset and the latest version?



Anyways, quick question you guys! I wanna try this, as Ive got a 93450c dvd-drive here now, but I dont have a 22 ohms lying around, but Im pretty sure Ive got hundreds installed in a bounch of defective machines Ive got lying around..

But to avoid having to use my multimeter and measure about 100 trillion resistors, does anyone know what machines they usually are installed in? What types of gadgets?

And the most important question, can I successfully do this without a OHM resistor at all conencted on the ground wire? Dont wanna ruin the drive

[iateshaggy]

you are looking for one w/ 2 red lines then one black one.  there is a forth line, but it just has to do with tolerances.

This post has been edited by iateshaggy: Dec 8 2009, 06:41 PM

[pastortom]

QUOTE(iateshaggy @ Dec 8 2009, 07:39 PM)

you are looking for one w/ 2 red lines then one black one.  there is a forth line, but it just has to do with tolerances.

okey.. I will try and look for that,, but still, is the resistor 100% necessary for this to work?

[iateshaggy]

i think so.  there have been reports of a 22 not working and them having to move to a 20.

[Shutdown[Swe]]

worked great when i switched from xp 32bit to windows 7 64bit had some issues dumping with doslash 32 in xp but w7 worked instantly so i suggest people try that if you are experiencing short freezes and are unable to dump it (even with drive present and status 72 )

[Gujs]

Hi, I am new in this xbox hacking scene. I just bought one   . I am just reading all the different tutorials and posts around here to figure out how to hack it myself. And now I have some questions on which I hope you guys will answer me.

1. I have LiteON 93450c, is this the same as 93450?
2. Do I need to read and write firmware when dvd is positioned in half open tray?
3. Do I need via sata pci card, because I can't find if stock sata on intel motherboard is enough?

I think I know the other things, and this is all I need right now to get me started. But if I will get stuck in the middle of the flashing process I will come back with more questions   .

[pastortom]

QUOTE

' date='Dec 8 2009, 09:13 PM' post='4585794'] worked great when i switched from xp 32bit to windows 7 64bit had some issues dumping with doslash 32 in xp but w7 worked instantly so i suggest people try that if you are experiencing short freezes and are unable to dump it (even with drive present and status 72 )

Aight, great..

But atm, Im only getting status 0x51 and 0x52 when I turn it on with the switch on..

I even try with the dvd-drive tray ejected half way out..

Nothing works..

no 0x72 =/ MTK vendor intro fails..

But it reckognizes the drive as a 93450c firmware revision and Liteon.. but the MTK Vendor Intro fails..

Now, the only possible two reasons Im left with is either:

1) the resistor Im using is wrong (ive measured it at 20k and it shows as 2.21, which Im pretty sure is 20 ohms)

2) the PIN101 is not properly cut away from the line above.. (AND HERES THE THING.. Ive cut it, and Im 99% certain its cut, probably cut it 15 times, and it looks 100% cut, but still my multimeter shows it as still connected to the line above)..

HALP?!

[pastortom]

QUOTE(jokerbrazil @ Dec 2 2009, 09:51 PM)

Hello there.

I did as the image + 22ohm resistor etc..  ( Ck3tool + Dosflash32 V1.8 ) Read the firmware  but i'v got a problem.

The orig.bin extracted dont open on Jungle flash 1.67 neither the hacked ix1.6  

Orig.bin extracted shows ff ff ff on Hexadecimal.  But the hacked seems ok.


The drive still ok ( i'v made stock traces again on PCB and the drive is working. )

Anyone has some idea ??


JOKEr

Did you try to open the fw in the "destination" window?

[pastortom]

QUOTE(pastortom @ Dec 8 2009, 09:57 PM)

Aight, great..

But atm, Im only getting status 0x51 and 0x52 when I turn it on with the switch on..

I even try with the dvd-drive tray ejected half way out..

Nothing works..

no 0x72 =/ MTK vendor intro fails..

But it reckognizes the drive as a 93450c firmware revision and Liteon.. but the MTK Vendor Intro fails..

Now, the only possible two reasons Im left with is either:

1) the resistor Im using is wrong (ive measured it at 20k and it shows as 2.21, which Im pretty sure is 20 ohms)

2) the PIN101 is not properly cut away from the line above.. (AND HERES THE THING.. Ive cut it, and Im 99% certain its cut, probably cut it 15 times, and it looks 100% cut, but still my multimeter shows it as still connected to the line above)..

HALP?!
 

Aight, I managed to successfully read a full dump of the 93450c firmware as well as spoofing the template iXtreme 1.6 93450c file, and erasing + flashing the drive.. Everything works 100%!!  

The mistakes I did was as following : Didnt cut the 2. trace as shown in the diagram, somehow missed that, yes, the first cuts I did above PIN101 was 100% correct, it was the 2.trace all along and didnt have the correct ohm resistor.. Found a 20 ohms, which worked wonders!

And since I met so many walls during these 4-5 hours, which I found solutions to, I thought Id make a video guide on all of it.. With thanks to everyone who helped me..

Cypher21, Prankster, John_ and Co! And ofcourse carranzafp/Maximus for the template firmware, the guide and the testing he's been doing.. Also Jungleflasher Team and all of the associated programmers in these en-devours!

I actually managed to rip off the VIA PIN 101 point, but also managed to fix it, which Ive also made a short video about!

Im gonna edit the videos, and upload them before I go to bed, and Ill add them in this thread for you other guys who meet walls when it comes to this flashing!

BE VIGILANT!

[pastortom]

Aight, made 1 video guide (3 parts )on how to successfully read/dump the 93450c Liteon as well as erase and write with proper working iXtreme 1.6..



Hope you'll enjoy them guys

Been working on this for about 10 hours now, time for bed ^^,

[xboxer360]

i've done over 10 of these now, but i'm stuck with one wierd one, gives me status 80 then 52, no matter what i try, it's like the spi is staying powered up, I have lifted both 3.3v pins and the 1.8, cut traces below, plug it in xbox and it still runs games.... i'm stumped.

if anyone wants a solderless way, no trace cuts, no pin removal, just bridge 100 and 101 on intro, once it detects, unbridge read and voila, just use a pin or the tip of your multimeter, have done a few this way and none have been damaged.

This post has been edited by xboxer360: Dec 9 2009, 07:57 AM