Print

[Egooo]

Can I use this as I have no original nand ? only xbr

[NeO_CooL]

Done on a Xenon without a problem just followed directions in here.

Launch FLASH360 on XBOX from USB key and make a full nand backup (button X)
then on PC launch Easy FreeBoot
Click Create Image
Open saved nand backup
Enter your CPU key

Easy FreeBoot will finish and create a Updflash.bin
Copy Updflash.bin to the usb key (i´ve copied to the root of the usb pen)

Gone to XBOX, launched XeXmenu 1.1 and then runned FLASH360 Xex
Button A (write updflash.bin to Nand)
Button B (Raw Flash without keeping current kv/config).
ignore the warnings ("WARNING: Keyvault encrypted data check mismatch" and "WARNING: Your current nand is not the ZeroPaired."). Pass this with Start button

Pressed A after the 2 warnings to continue with the flash

Wait until it´s flashed
Back
Back to Turn off Xbox 360
It turn´s off by it self

Remove Usb pen
Remove power cord and wait 2 or 3 minutes

Press power button

Now configure language and resolution
Will ask about an update, just press OK (Don´t know if this happens without a live profile, mine is for avatar items)

Download
_tt_://download.microsoft.com/download/4/1/D/41D9A2BA-3B48-4BD5-B613-122E7C3A1390/SystemUpdate12611.zip

extract SystemUpdate12611.zip on USB key,
insert the USB key to your xbox and follow the instruction to update,
after few seconds you'll have a working new dash with avatar!!!

Enable Console Safety
Set passcode and reset
Go to parental controls and disable
- Xbox Live connection
- Xbox Live account creation
Set all ratings to unblocked (defaults are like PG-13 for films and etc)

All made with resistor R6T3 on place!!!

Wait for a new Freestyle dash or use the one available.

Anyone noticed the temperature is lower?

Used some posts on this forum, so thanks to those people.

PS: I do have a original nand but i´ve chosen to use the backup made by flash360 as my original nand had CB 120 and freeboot 9199 had Cb 121. So just used what was working this months.

[Egooo]

I have error    img  http://wrzucacz.pl/file/3171289647018]

Error Cauld not find file sysupdate.xexp1
error Unhandled exception

[scuzzie2k]

QUOTE(scuzzie2k @ Nov 12 2010, 05:52 PM)

After you uploaded the nand with the new dash I created via the Freeboot tool do you have to do another update? and the game was run from freestyle dash.  I now got e79 !!!

Anyone please advise I got a stuffed console cant do anything

[omegastar]

I got the new cat version but still have the same issue when I get the iflash window and hit any key it disappears and stops on my Jasper 256 with original nand dump and freeboot0.32 dump.

[rfisher1968]

QUOTE(Egooo @ Nov 13 2010, 06:17 AM)

I have error    img  http://wrzucacz.pl/file/3171289647018]

Error Cauld not find file sysupdate.xexp1
error Unhandled exception

I had the same problem, my nand was xbr still. All i did is used bestpigs toolbox to update to freeboot first 9199, then it worked perfectly.

[boflc]

QUOTE(Egooo @ Nov 13 2010, 06:45 AM)

Can I use this as I have no original nand ? only xbr

i could be wrong, but i think either original nand or freeboot 0.032 image is currently required.  upgrade to freeboot - i know i've seen a bunch of tuts on that process.

[Inuyasha152]

QUOTE(Haygar @ Nov 13 2010, 01:44 AM)

Another satisfied JasperBB customer. Updated smoothly with this app. and also avatar updated with the official, all with R6T3 intact.

Edit: @Inuyasha, I used my orig nand to build if you have that?! And those files you are having skipped aren't needed IMO, I just updated dashlaunch 2.04 manually afterwards.
If you are able to create an image and check it in 360 Flash Dump Tool, I have 29 files. Swat I found for both the BB and Falcon

Just updated my Jasper BB & Falcon console using dumps fromn 9199 (don't have originals). Worked perfectly! Thanks for the info, and especially thanks to Sneaky Peanut for such a simple process

[selfser]

I'm using flash360 and I keep gettinga msg saying -your nand is not the zeropaired when i try to inject it the updateded file.  Any Suggestions?

[boflc]

QUOTE(selfser @ Nov 13 2010, 03:38 PM)

I'm using flash360 and I keep gettinga msg saying -your nand is not the zeropaired when i try to inject it the updateded file.  Any Suggestions?

i just accepted that and flashed.

[DuggyUK]

holy cow, this tool is ace, "it just works", 2 consoles done, Xenon and Falcon (had to remap bad blocks as flash360 iirc doesn't)

 

[DragonNZ]

Hi There,
I have a issue I can't figure out and hope someone can help.
The update flash is created, and I flash it using the flash360 tool, it complains about the difference, and I press START to continue and flash the NAND.

I then power down, and unplug all for a minute. When I boot back up, it displayes the new 360 splash screen, and hangs at that point without loading the standard dash. I can still boot into Xell using the eject button and can reflash backup to recover. This also happens if I create the flash using Easy Freeboot. I am currently using freeboot 0.032 (Dashboard 9199) and are using the dump of that to create the new flash. Do you know what I am doing wrong for it to not boot the 12611 dash and hang at the splash screen? Thanks for your help.

[Haygar]

QUOTE(omegastar @ Nov 13 2010, 11:25 PM)

I got the new cat version but still have the same issue when I get the iflash window and hit any key it disappears and stops on my Jasper 256 with original nand dump and freeboot0.32 dump.

I found I had to click 'no' when is asks if you have a specific CB, even if it's the one you know you have, after that the program would run fine without disappearing after pressing any key. And I was pressing the any key.  After that I checked that the CB was correct in 360 flash tool

QUOTE(DragonNZ @ Nov 14 2010, 07:46 AM)

Hi There,
I have a issue I can't figure out and hope someone can help.
The update flash is created, and I flash it using the flash360 tool, it complains about the difference, and I press START to continue and flash the NAND.

I then power down, and unplug all for a minute. When I boot back up, it displayes the new 360 splash screen, and hangs at that point without loading the standard dash. I can still boot into Xell using the eject button and can reflash backup to recover. This also happens if I create the flash using Easy Freeboot. I am currently using freeboot 0.032 (Dashboard 9199) and are using the dump of that to create the new flash. Do you know what I am doing wrong for it to not boot the 12611 dash and hang at the splash screen? Thanks for your help.

Anymore info? Like what version motherboard and did you flash wothout keeping keyvault? I usually just rewrite everything including kv.

[ElecTriX]

Hi everybody! Just registered here 'cause I have a couple of question about updating my Freeboot.
I'm currently running Freeboot 0.032 (9199) on my X360 Jasper 512.

As I bought my xbox already JTAG:ed I'm currently below newbie-level when it comes to NAND-flashing and all that. Unfortunately the company closed so they are not available to answer the questions that I have. My question is following;

1. The company that did the JTAG said they "removed the possibility that future updates burn the uFuses".. Sounds good to me, but may this be a problem when updating to 12611?
2. Don't know if they removed "R3T6" ? Is this standard when doing JTAG and what if they did not remove it? What can happen?
3. I received a dvd-disc containing many files; Folder "66mb" containing "nand1.bin" -> "nand3.bin", all of the same size 69 696 KB. Folder "512" containing "nand1.bin" -> "nand3.bin", all of the same size 540 672 KB and also a text-file named "badBlocks".  What's the difference between the files as they are different sizes? Also, why is there 3 files?
4. What's best, using the original NAND or the 0.032-NAND? If using the original NAND might bad blocks be a problem?
5. When flashing on xbox, keep KV and config or not? What's best and why?

Sorry for all the questions and hope none of you judge me for being a newb, want to learn! If you have links that might answer the questions above please send me!

[DragonNZ]

QUOTE(Haygar @ Nov 14 2010, 10:06 AM)

Anymore info? Like what version motherboard and did you flash wothout keeping keyvault? I usually just rewrite everything including kv.

It is a Jasper 16Mb CB 6723 (Verified in 360 Flash tool, and Easy GUI Frebooter). I have tried flashing both keeping the keyvault (Option A in Flash360) and overwriting the values (Option B in Flash360). Both times when I reboot, the splash screen is displayed and hangs at that point.