Print

[hundshamer]

QUOTE(Travulese @ Jun 8 2010, 06:19 PM)

Thanks, Ye I figured that out.. I was just getting confused.. thx for the quick reply.. appreciate it man.

can you use the freeboot image that you used to install to your nand and run freeboot with, Like I took the smc out of my freeboot image that I created with jtag tool 1.72 so im using the image that I had flashed into my nand and actually had it working but then the ft1u2 trace fell off and I got screwed and then I did another one and it fell off, the worst of luck.. basically Im asking if the freeboot.bin that I created using jtag tool 1.72 is fine to extract the smc and then inject the new smc into the file using smc update v0.2

Yes, but I suggest you update to freeBOOT toolbox v2.4.

[Travulese]

QUOTE(hundshamer @ Jun 8 2010, 08:05 PM)

Yes, but I suggest you update to freeBOOT toolbox v2.4.

I did everything like I said before solderd to aud_clamp then I solderd to tray_open and still no go.. im using the xecuter quick solder board and it let me choose resistor levels. Im stumped.. I solderd all to the rite places and nothing is working still e79..

[Travulese]

QUOTE(krizalid @ Jun 6 2010, 11:12 PM)

I have and It works great, but if you do it on a Zephyr, your DVD Drive will always eject during boot.
This does not happen on my Falcon and I don't know about jaspers, since I don't have one to test.

Another option is to use TMS=ARGON_DATA (rf_board) and TDI=OPEN_TRAY on Falcons and japsers, and they will work fine, except for the charge kit issue.  

krizas how exactly did you use this tool? did you use your freeboot.bin nand? I used my freeboot.bin that I created then extracted the smc and then added the new smc to the bin I extracted it from.. am I doing this correctly? Im still getting e79 after I changed the settings to aud_clamp and tray_open signal I solderd the wire to the bottom of the board (tray_open signal) it said that was fine on this pdf I have..

any help would appreciated

[Definitely Wapner]

Quick question. Do I pull the smc from my freeboot NAND or do I pull the smc from xell image and then have it patched to my freeboot NAND?

[Travulese]

QUOTE(Definitely Wapner @ Jun 9 2010, 08:32 AM)

Quick question. Do I pull the smc from my freeboot NAND or do I pull the smc from xell image and then have it patched to my freeboot NAND?

Im wondering the same, I wonder if I got it rite. I extracted the nand from my freeboot.bin then it made a 12kb falcon.bin (smc image) then I updated my freeboot.bin and chose the options I wanted.. I have no clue if this is the correct way... hopefully someone can help us out on how to properly use this program.

[tsunami666]

Use the smc_dec.bin extract from the xbr_3 image, i always used that smc.

[Definitely Wapner]

QUOTE(tsunami666 @ Jun 9 2010, 11:12 AM)

Use the smc_dec.bin extract from the xbr_3 image, i always used that smc.

What about with Freeboot though? I extracted the SMC from my freeboot image (I have a zephyr 4580 so I'm using Falcon freeboot .32).

I extracted the SMC from the freeboot, tried patching it with the zephyr patch once and tried patching it with the falcon patch once and both give me no video when I boot. I patched with just AUD_CLAMP only and changed the wiring like I needed to.

I am going to try to run it patched without the wiring change (option 1 in the tool) and use the original wiring to see if that helps. For some reason it's not booting with picture for me, but I don't get any RROD or e79 errors. Odd problem.

Any help is good.

[Travulese]

QUOTE(RRODXbox @ Jun 4 2010, 12:16 PM)

Having problems with this.

I made a freeboot image for a Zephyr with FB toolbox then went to reconfigure the SMC with this and changed the rol spot to AUD_CLAMP, got E79 on boot so I know its changed the SMC, moved the wire and I dont get any dashboard booting but Xell will boot fine, just get a blank screen and no errors.  

Any ideas? its the 1st time I have tried this.

RRODXbox your inbox is full so I cant pm you, I added you to msn.

[krizalid]

I have just figured out that not all 360's are compatible with FreeBoot nand dump modified with this tool

I'll edit the first post to remove "FreeBoot support"

It worked good on 1 zephyr and 2 falcons, but this new zephyr I got, I used my own tool to update on nand freeboot v0.32 and no video output.

Due to the re-encryption, there's a chance that it should'nt be working at all, except for Xell and XBR.
Funny thing is that it worked on me.


I suggest you start using SMC_IO v0.2B which now add a similar interactive menu to what I have done here.

Difference; it will not inject to nand file, but will build the SMC for you to update building new FreeBoot image with ibuild.

[az42b]

Guys FreeBoot is VERY easy to get working with this!

What you need to do is patch the SMC in your XBR image and make sure it boots properly. Then you have to extract your SMC.bin, SMC_config.bin and KV.bin from the XBR image (through iBuild i believe) then manually assemble a FreeBoot image using iBuild

[Definitely Wapner]

When I run iBuild on my windows PC, I get a libeay.dll error...fix?

[uk_dan2k]

does anyone know if this supports the current dash 12611, i can make 9199 images then patch with this tool and it boots fine.

 

but when i try with the latest dash i get stuck with green power led, and no video (eject still boots xell).