Print

[BadBloke]

QUOTE(cartok @ May 20 2010, 03:57 PM)

Hi
I tried Autohacker severel times works perfect. I jtagged xenon, falcon boards.
But now I'm tring jasper board always gives error.

I dumped two times with option called "Read Bootloader" . They are match.
But when I started write nand,always gives different errors.
I tried 20 times always error. What should I do now?

P.S. Sorry my poor english

It is a BB, right? 256 or 512?
What kind of errors?
It gives errors before writing and the write doesn't start?
It gives errors during write or the log has errors?
Or it writes and the console doesn't work?

Please be more specific, I want to fix this in case there is a problem, although the application is becoming obsolete now that FreeBOOT is around  

[asapreta]

It don't recognize a Zephyr 4558.

[omegastar]

I have used this awesome tool to do a couple xenons and it worked great. But then I tried doing a 256MB Jasper it showed up as CB 6712 i dumped the bootloader it said 2 files matched no errors so I then clicked patched and then began to write XBR it started wrote a few blocks then bam error on every block and when I power on console no video or rings etc. May have been bad wiring dont know I resoldiered and tried to redump i get error 210/218 on the same dozen blocks all low numbers like 37 39 77 and it shows as CB 6723 now but dumps never match. Also trying to check my original dumps in xnandhealer they show as matching but not good dumps.

[sfear2ugf]

hello yall im some what new i have jtag like 8 Xbox well i never done a jasper 512 i was been using this very nice autohacker so i dumped 2 full nand, compared,  PATCH and flash the xbr on the xbox and just got the Christmas lights so i re flashed my dump1 and now im dumping with the Read Bootloader i not sure what i have to do im guessing i do the same thing i been doing?

1# Dump with Read Bootloader

2# compare

3# PATCH/Inject KV and Confing

4# WRITE XBR

Right?   (IMG:style_emoticons/default/uhh.gif)

This post has been edited by sfear2ugf: May 24 2010, 05:02 AM

[BadBloke]

QUOTE(omegastar @ May 24 2010, 02:56 AM)

I have used this awesome tool to do a couple xenons and it worked great. But then I tried doing a 256MB Jasper it showed up as CB 6712 i dumped the bootloader it said 2 files matched no errors so I then clicked patched and then began to write XBR it started wrote a few blocks then bam error on every block and when I power on console no video or rings etc. May have been bad wiring dont know I resoldiered and tried to redump i get error 210/218 on the same dozen blocks all low numbers like 37 39 77 and it shows as CB 6723 now but dumps never match. Also trying to check my original dumps in xnandhealer they show as matching but not good dumps.

Sounds like bad wiring...
If the KeyVault is ok - and maybe config block, too - (only a couple of blocks of good data are needed) you can still patch XBR and have a working jtag system.

QUOTE

hello yall im some what new i have jtag like 8 Xbox well i never done a jasper 512 i was been using this very nice autohacker so i dumped 2 full nand, compared, PATCH and flash the xbr on the xbox and just got the Christmas lights so i re flashed my dump1 and now im dumping with the Read Bootloader i not sure what i have to do im guessing i do the same thing i been doing?

1# Dump with Read Bootloader

2# compare

3# PATCH/Inject KV and Confing

4# WRITE XBR

Right?  

Christmas lights usually means there is no keyvault/bad keyvault. If you have already written your NAND once, there's no point in backing up (dumping). Try patching again using the original dump as source, ERASE your NAND (sometimes they fail to write) and then WRITE XBR. Remember, if you're using LPT, it may take a couple of writes until you get it right...

[sfear2ugf]

QUOTE(BadBloke @ May 24 2010, 06:14 AM)

Sounds like bad wiring...
If the KeyVault is ok - and maybe config block, too - (only a couple of blocks of good data are needed) you can still patch XBR and have a working jtag system.
Christmas lights usually means there is no keyvault/bad keyvault. If you have already written your NAND once, there's no point in backing up (dumping). Try patching again using the original dump as source, ERASE your NAND (sometimes they fail to write) and then WRITE XBR. Remember, if you're using LPT, it may take a couple of writes until you get it right...

Thanks for the help ok i have re flash once the xbr.bin without no badblocks once i turn on the xbox it powers up but i don't get no video or NO Error.......
i Have flash like 5 times now and flashed back to the back up nand dump1 and work fine but no luck with the xbr.bin??
 
The CB is 6723 on a jasper 512
im also using a USB

i really don't think it have to do with the XBR_JasperBB_8955_3 ? should i try feeboot ? if so what is the file called and where do i get it sorry but i have nerve used feeboot??  

[BadBloke]

QUOTE(sfear2ugf @ May 24 2010, 10:02 PM)

Thanks for the help ok i have re flash once the xbr.bin without no badblocks once i turn on the xbox it powers up but i don't get no video or NO Error.......
i Have flash like 5 times now and flashed back to the back up nand dump1 and work fine but no luck with the xbr.bin??
 
The CB is 6723 on a jasper 512
im also using a USB

i really don't think it have to do with the XBR_JasperBB_8955_3 ? should i try feeboot ? if so what is the file called and where do i get it sorry but i have nerve used feeboot??  

Did you erase the NAND at first? All of it? BB's tend to have issues regarding the filesystem of the NAND (the "MU" part of it) and the user sometimes needs to erase the whole NAND, write XBR, and never use the MU again, otherwise it will eventually get screwed up again, won't boot.

If the original dump works, the JTAG will work, too, if done properly. Do a complete erase of your NAND, download XBR again, make sure you have a 512MB NAND (I have seen people get it wrong regardless of their experience) and try again. You're bound to win.

Freeboot is a completely different story, needs to be compiled and this tool can't do much about it (yet?).

[sfear2ugf]

Ok i well try what you have told me to do

also would this help you

I have checked manually with Hex workshop hex editor 6 and at 00008400 i have (43 42 1A 43) is that good?

and i well get back to you! thanks.

[sfear2ugf]

QUOTE(BadBloke @ May 26 2010, 04:33 PM)

Did you erase the NAND at first? All of it? BB's tend to have issues regarding the filesystem of the NAND (the "MU" part of it) and the user sometimes needs to erase the whole NAND, write XBR, and never use the MU again, otherwise it will eventually get screwed up again, won't boot.

If the original dump works, the JTAG will work, too, if done properly. Do a complete erase of your NAND, download XBR again, make sure you have a 512MB NAND (I have seen people get it wrong regardless of their experience) and try again. You're bound to win

ok so i have Erase the nand of the xbox im not sure but when you say erase the nand you want me to boot up the xbox and format the MU??? Or you want me to start AutoHacker and Hit Erase???  

[omegastar]

Key word was used ERASE!  

[sfear2ugf]

QUOTE(omegastar @ Jun 3 2010, 10:48 AM)

Key word was used ERASE!  

NOP Did not work ??