Topic: 360 Modification Disc v1.6 (Read 913 times)

boochip · « **Reply #60 on:** May 22, 2009, 04:59:00 PM »

Thanks frosty works good on a sammy

Got an error about wrong port but that was because i had sata connected when pc booted

but worked fine when i restared and only plugged sata in when it said on screen

noi · « **Reply #61 on:** May 23, 2009, 04:06:00 AM »

got it from the usual way...it is ok now and UP. thanks, will test it today.

shained · « **Reply #62 on:** February 04, 2020, 09:54:00 AM »

Hi everyone.

I'm new to the modding scene and saw this disc up on newsgroups so grabbed and it read up about it and felt like I was ready to go.

I've undone my 360 and I've got a phillips/lite on DG - 16D2S drive.

Now i've read comflicting things when I get to this point.

Do i just connect the drive (leave it in the x box or remove it altogether) to my sata card and run the disc on my pc?

Or does this type of drive require soldering and so on like i've read in some places.

Any help at all would be greatly appreciated

FrostyTheSnowman · « **Reply #63 on:** May 23, 2009, 12:29:00 PM »

QUOTE(shained @ May 23 2009, 10:54 AM)

Hi everyone.

I'm new to the modding scene and saw this disc up on newsgroups so grabbed and it read up about it and felt like I was ready to go.

I've undone my 360 and I've got a phillips/lite on DG - 16D2S drive.

Now i've read comflicting things when I get to this point.

Do i just connect the drive (leave it in the x box or remove it altogether) to my sata card and run the disc on my pc?

Or does this type of drive require soldering and so on like i've read in some places.

Any help at all would be greatly appreciated

The Lite-On drive requires a special serial cable to be modded, either the CK3 Pro, the Maximus Xtractor, or make your own cable (homemade).

Do not attempt to modify your Lite-On drive without this cable, or you might brick your drive...

shained · « **Reply #64 on:** May 23, 2009, 12:34:00 PM »

Are these cables easy to make/cheap to buy?

FrostyTheSnowman · « **Reply #65 on:** May 23, 2009, 01:50:00 PM »

QUOTE(shained @ May 23 2009, 11:26 AM)

Are these cables easy to make/cheap to buy?

Cheap to buy, no. The cable is roughly $50 for a CK3 Pro...

However, they are very cheap to make.

($5 in parts)

Check out the 'Lite-On-RS232-TTL.jpg' image file included in the 360 Modification Disc v1.6 package for the diagram.

NOTE: Even with this cable you still need to use your 360 to power the drive, the serial cable in the diagram does not provide power to the drive.

Dark-Knight · « **Reply #66 on:** February 04, 2020, 12:00:00 PM »

Hi, I have a few questions.
1. Please enter your VT6421's port below?
I have the RC215 my ports are I/O Range
8000-800F
8400
8800
8c00
9000
9400 How many should I enter? I enter 8000 but want to clarified
I always get MTK vendor intro failed on port 0x8000 and I tried each one and the result is the same.

2.Please enter the com port for use with your serial cable(Lite-On drives only)
Do I press enter and skip it?

3.I finished every step and this is what I got
From Status 0xD1 to Status 0x70
Rading Bank 0,1,2,3 Then Reading finished! Datasum:158 F

Finally how do I know when I am finish. because I tried my xbox360 and my back ups wave 3 don't start. Another thing do i need to power on my 360 when it prompts me to hit y and wait for dos to find the drive?
Thanks for everything.

Reaper527 · « **Reply #67 on:** May 23, 2009, 02:41:00 PM »

QUOTE(Dark-Knight @ May 23 2009, 03:00 PM)

Hi, I have a few questions.
1. Please enter your VT6421's port below?
I have the RC215 my ports are I/O Range
8000-800F
8400
8800
8c00
9000
9400 How many should I enter? I enter 8000 but want to clarified
I always get MTK vendor intro failed on port 0x8000 and I tried each one and the result is the same.

2.Please enter the com port for use with your serial cable(Lite-On drives only)
Do I press enter and skip it?

3.I finished every step and this is what I got
From Status 0xD1 to Status 0x70
Rading Bank 0,1,2,3 Then Reading finished! Datasum:158 F

Finally how do I know when I am finish. because I tried my xbox360 and my back ups wave 3 don't start. Another thing do i need to power on my 360 when it prompts me to hit y and wait for dos to find the drive?
Thanks for everything.

did you only read the firmware, or did you actually finish flashing the drive? i think you missed a point where you were supposed to press enter to get to the next screen.

darkcrudus · « **Reply #68 on:** February 04, 2020, 12:45:00 PM »

QUOTE(Reaper527 @ May 23 2009, 02:33 PM)

did you only read the firmware, or did you actually finish flashing the drive? i think you missed a point where you were supposed to press enter to get to the next screen.

i get to this point
Rading Bank 0,1,2,3 Then Reading finished! Datasum:xxxx
and when it asks me if it was succesful hit y/n i cant type anything, do you know whats wrong?

Dark-Knight · « **Reply #69 on:** February 04, 2020, 12:50:00 PM »

After it said Reading Finished! Datasum: 158F my computer freeze. Can someone answer some on my earlier questions.

darkcrudus · « **Reply #70 on:** May 23, 2009, 03:09:00 PM »

QUOTE(Dark-Knight @ May 23 2009, 02:50 PM)

After it said Reading Finished! Datasum: 158F my computer freeze. Can someone answer some on my earlier questions.

exactly the same problem im having man v.v ive tried both the disc and the usb version

boochip · « **Reply #71 on:** February 04, 2020, 01:44:00 PM »

QUOTE(Dark-Knight @ May 23 2009, 02:50 PM) *

After it said Reading Finished! Datasum: 158F my computer freeze. Can someone answer some on my earlier questions.

QUOTE(darkcrudus @ May 23 2009, 09:01 PM)

exactly the same problem im having man v.v ive tried both the disc and the usb version

your computer is not hanging, Frosty allready explained what was happinging in this very tread (IMG:style_emoticons/default/dry.gif)

darkcrudus · « **Reply #72 on:** February 04, 2020, 01:57:00 PM »

=/ i dont have a PS/2 keyboard

Scavx · « **Reply #73 on:** May 23, 2009, 04:48:00 PM »

QUOTE(FrostyTheSnowman @ May 23 2009, 08:21 PM)

Do not attempt to modify your Lite-On drive without this cable, or you might brick your drive...

It seems that i have bricked my Lite-on drive...

I have all the key and dummy files extracted by JungleFlasher, is there any way I can unbrick it?

What tools and SF I'll be needing?

Thnx for your answers in advance! *)

Dark-Knight · « **Reply #74 on:** May 23, 2009, 07:00:00 PM »

boochip next time you quote a comment make sure you give a helpful answer. Don't say they already answer it. I don't know if you are stupid or what but next time let frosty or someone else answer. Anyways I have a ps/2 and again nothing. It says Reading finished! Datasum:158F and that's it. I try everything, pressing every key on my keyboard turning the xbox 360 drive on and off and ejecting the drive and nothing. WTF frosty come up with something. And boochip make sure you don't answer. I can even make a video and see what's going bad.

Author Topic: 360 Modification Disc v1.6 (Read 913 times)