Print

[gmos]

QUOTE(vlj9r @ Nov 14 2008, 02:32 AM)

From reading this forum and all 36 pages of the TheSpecialists thread, I know that some folks have had success with it but I can't get this one to flash. I've tried nvidia, intel and VIA chipsets that other folks have reported success with but still no joy. With all of the above controllers, I have been able to detect the WD drive, run hddhacker -f and create the undo.bin file. The problem comes when it tries to flash the drive. I get a FATAL ERROR: the EC sector count was not found in the FW. Does this mean that my hddss.bin file is bad?

My current sata controller is the VIA VT6421A which other have reported great success with. Could this HD have a newer firmware that is not compatible with HDDHACKER?

I'm stomped and I have not been able to find the meaning of the error message.

I also using the same HDD + nvidia cipset
but mine the hddhacker does not detect my hdd (hdd available on bios).

[early105]

QUOTE(gmos @ Jan 13 2009, 05:38 PM)

I also using the same HDD + nvidia cipset
but mine the hddhacker does not detect my hdd (hdd available on bios).

I'm also using nvidia chipset, but on 22RST0.

At first, hddhacker 0.91 also could not detect my HD. After using HEX edit on the hddhacker.rom with the SATA info. by running msinfo32 to capture, the 120G got recognized by hddhacker finally and flashed sucessfully. (you need to try which set of SATA info. (IRQ) works on your HD; mine, I have 3 sets of SATA info., I got success on the 2nd time)

BTW, if you're using VISTA like me, you got to run xplorer360 under administrator mode.

However, I still have a problem that I cannot move the files (in partition 3 of 20G backup) back to the new 120G...

drag & drop is not allowed; even using the "Insert folder", "Injecting" is showed up during the process, but nothing can be seen in the 120G at the end...

Wondering to get a memory unit to move my saves and profile...

[moobypets]

i have a new nvidia bord since my old one just died and whit my old one i could only use the hddhackr on the sata 2 port only one it was working and the other 2 where not

but it was still ok

now i have a new nvidia bord nforce 430 and when i check msinfo

i get this 2 different sata and i have 4 slot and i want to use the last slot iff possible

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&40
I/O Port 0x000009F0-0x000009F7
I/O Port 0x00000BF0-0x00000BF3
I/O Port 0x00000970-0x00000977
I/O Port 0x00000B70-0x00000B73
I/O Port 0x0000DC00-0x0000DC0F
Memory Address 0xFE02D000-0xFE02DFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)

and the second one

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&41
I/O Port 0x000009E0-0x000009E7
I/O Port 0x00000BE0-0x00000BE3
I/O Port 0x00000960-0x00000967
I/O Port 0x00000B60-0x00000B63
I/O Port 0x0000C800-0x0000C80F
Memory Address 0xFE02C000-0xFE02CFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)


plz could some one tell me what code should i put in the hex editor and where

or just email me a file that has the code already in plzzzzz i need help im not getting this as the code as to be 4 bytes and as to be 7 digit apart im getting lost here and this is out off my league to hex edit

im not that good


i need help bad

[Simple Fix]

QUOTE(moobypets @ Apr 8 2009, 10:35 PM)

i have a new nvidia bord since my old one just died and whit my old one i could only use the hddhackr on the sata 2 port only one it was working and the other 2 where not

but it was still ok

now i have a new nvidia bord nforce 430 and when i check msinfo

i get this 2 different sata and i have 4 slot and i want to use the last slot iff possible

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&40
I/O Port 0x000009F0-0x000009F7
I/O Port 0x00000BF0-0x00000BF3
I/O Port 0x00000970-0x00000977
I/O Port 0x00000B70-0x00000B73
I/O Port 0x0000DC00-0x0000DC0F
Memory Address 0xFE02D000-0xFE02DFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)

and the second one

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&41
I/O Port 0x000009E0-0x000009E7
I/O Port 0x00000BE0-0x00000BE3
I/O Port 0x00000960-0x00000967
I/O Port 0x00000B60-0x00000B63
I/O Port 0x0000C800-0x0000C80F
Memory Address 0xFE02C000-0xFE02CFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)
plz could some one tell me what code should i put in the hex editor and where

or just email me a file that has the code already in plzzzzz i need help im not getting this as the code as to be 4 bytes and as to be 7 digit apart im getting lost here and this is out off my league to hex edit

im not that good
i need help bad