Topic: TheSpecialist's HDDHackr v0.91 - Adds Support for WD BEVS-RST Drives (Read 6224 times)

crow610 · « **Reply #615 on:** March 15, 2009, 02:28:00 PM »

My stupid laptop does not have a SATA port (only PATA) so I'm wondering if this tool will work if the drive is plugged into a USB enclosure.

Thanks in advance.

treyjazz · « **Reply #616 on:** March 18, 2009, 12:45:00 PM »

Mwave has them for ~$56 shipped 3 day (worth paying a dollar more over newegg's price because their free shipping sucks). The one I got from there recently is a VAT0 model.

Is anyone able to run original Xbox games? I manually created a Partition 2 and ran the Xbox support installer and it looked like it installed w/o any problem. But when I go to run Halo, Halo 2, etc it always tells me to download the game again and never gives me the option to install it to the drive. However, I am able to copy 360 games to the drive and also download demos off of Live so it's got me puzzled.

Also has anyone had any problems running undo with HDDHackr? It always tells me that my drive isn't supported and to make sure it is a BEVS drive. Obviously this is a problem since it is a 'Fujitsu'. How ironic...

treyjazz · « **Reply #617 on:** March 18, 2009, 02:10:00 PM »

Did some more searching and found the solution to the Xbox originals problem (that you *need* an image of partition 2 on an original drive for the emulator).

As for the undo problem it was due to the SATA controller card I was using and a different PC was able to undo it. Strange since it was able to flash it and read the firmware correctly...

djkarupt · « **Reply #618 on:** February 03, 2020, 09:28:00 AM »

so only BEVS.....BEAS wont work?

buzz44 · « **Reply #619 on:** March 22, 2009, 12:05:00 PM »

QUOTE(djkarupt @ Mar 23 2009, 03:28 AM)

so only BEVS.....BEAS wont work?

BEVS, BEVT and BEAS drives will all work.

mr2000jp · « **Reply #620 on:** March 23, 2009, 03:48:00 PM »

QUOTE(brywalker @ May 8 2007, 05:52 PM)

You know, after I posted I knew it would be taken the wrong way.

Let me rephrase.

If you are not using your original hddss.bin from your 120GB and get one through illegal ways, you are not only breaking the law but chances are you will be banned from Live for using a cloned drive (since there will most likely be duplicates) if a detection is already working.

Also, AFAIK you cannot use your 20GB hddss.bin on the 120GB and expect results.

This is a warning and not a request. I have no need for the 120GB.

it looks like you are one of microsoft underdogs , just shut up ,
no one listen to that fool

sicx13 · « **Reply #621 on:** March 26, 2009, 06:46:00 PM »

i wanted to search this but its disabled. i got a WD BEV series HD 250 GB. and was thinking that just ghosting it using norton might work and faster than this. any input would be gtreatly aprecciated

d05register · « **Reply #622 on:** March 26, 2009, 07:36:00 PM »

QUOTE(buzz44 @ Mar 22 2009, 08:41 PM)

BEVS, BEVT and BEAS drives will all work.

Work also

BEKT 7200RPM confirmed by me http://forums.xbox-scene.com/index.php?showtopic=680644
Velociraptor 10000RPM http://forums.xbox-scene.com/index.php?showtopic=675652

buzz44 · « **Reply #623 on:** March 27, 2009, 03:13:00 AM »

QUOTE(d05register @ Mar 27 2009, 12:36 PM)

Work also

BEKT 7200RPM confirmed by me http://forums.xbox-s...howtopic=680644
Velociraptor 10000RPM http://forums.xbox-s...howtopic=675652

Nice

. IMO the first post should be updated.

baghdad-bob · « **Reply #624 on:** March 31, 2009, 10:40:00 PM »

I have a masscool sata with silicon image sil 3112 sata raid controller chip set, and when I run hddhakr -f and I hit y it says that i have to connect the right hard drive. I have a WD 12000Bevs-22usto

I/O ports
0x0000DC98-0x0000DC9B
0x0000DC9C-0x0000DC9F
0x0000DCA0-0x0000DCA7
0x0000DCA8-0x0000DCAF
0x0000DCB0-0x0000DCBF

This post has been edited by baghdad-bob: Apr 1 2009, 05:42 AM

moobypets · « **Reply #625 on:** April 08, 2009, 05:10:00 PM »

i have a new nvidia bord since my old one just died and whit my old one i could only use the hddhackr on the sata 2 port only one it was working and the other 2 where not

but it was still ok

now i have a new nvidia bord nforce 430 and when i check msinfo

i get this 2 different sata and i have 4 slot and i want to use the last slot iff possible

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&40
I/O Port 0x000009F0-0x000009F7
I/O Port 0x00000BF0-0x00000BF3
I/O Port 0x00000970-0x00000977
I/O Port 0x00000B70-0x00000B73
I/O Port 0x0000DC00-0x0000DC0F
Memory Address 0xFE02D000-0xFE02DFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)

and the second one

Name NVIDIA nForce Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_03F6&SUBSYS_26091019&REV_A2\3&2411E6FE&0&41
I/O Port 0x000009E0-0x000009E7
I/O Port 0x00000BE0-0x00000BE3
I/O Port 0x00000960-0x00000967
I/O Port 0x00000B60-0x00000B63
I/O Port 0x0000C800-0x0000C80F
Memory Address 0xFE02C000-0xFE02CFFF
IRQ Channel IRQ 23
Driver c:\windows\system32\drivers\nvgts.sys (10.3.0.42 built by: WinDDK, 142.53 KB (145,952 bytes), 8/18/2008 6:54 PM)

plz could some one tell me what code should i put in the hex editor and where

or just email me a file that has the code already in plzzzzz i need help im not getting this as the code as to be 4 bytes and as to be 7 digit apart im getting lost here and this is out off my league to hex edit

im not that good

Killazincorp · « **Reply #626 on:** April 10, 2009, 01:31:00 PM »

What is the biggest HDD i can upgrade to if I currently have a 20GB Microsoft hard drive? I don't understand the sector 16 stuff.

maninjapan · « **Reply #627 on:** April 13, 2009, 01:34:00 AM »

if you use YOUR bin dump file, then only 20gb is possible, regardless of the size of the new hdd. If you search, you can find 120gb, which at the moment is the biggest available.

Simple Fix · « **Reply #628 on:** April 13, 2009, 06:26:00 PM »

Well I have a WD BEVS-00UST0 Drive with a March 13 09 date on it (factory recertified ) and I have tried to flash this drive with a 6421 Sata Board plus my own 8237 chipset on my mobo and I just bought a Sil 35** chipset PCMIA card for my Laptop but I guess it doesn't work in DOS because it will not see any drive. None of these worked for me. So now I bought a Sil 35** chipset SATA PCI card and its on the way. I will say I just flashed 2 - 22UST0 drives perfectly with my 8237 chipset mobo. But this 00UST0 drive will not work for anything it keeps saying "EC sector count was not found in the FW" and I tried the HDD restore program on the last page with no luck. Also I have hex edited the HDDhackr program for every chipset I used and tried the normal way also and read for hours and hours but can't find any solutions!!

CAN ANYONE PLEASE HELP ME HERE I AM GOING CRAZY!!

maninjapan · « **Reply #629 on:** April 13, 2009, 07:46:00 PM »

Can you post pics of the msinfo32 and also of the edited hex file?

Author Topic: TheSpecialist's HDDHackr v0.91 - Adds Support for WD BEVS-RST Drives (Read 6224 times)