Topic: Samsung Drive Recognition In Windows (Read 154 times)

door2 · « **on:** June 17, 2006, 04:55:00 PM »

im trying to make a backup raw mode , flash the dvd properly but windows does not recognize the samsung drive , bios does however , any suggestions , or procedure , thanks

blackpornstar · « **Reply #1 on:** November 05, 2006, 07:22:00 AM »

I'm in the same boat. I've been searching for 2 days now and haven't found a solution. Anyone have any suggestions??? Thanks...

Romps · « **Reply #2 on:** November 05, 2006, 09:56:00 AM »

If u talking about the samsung 360 drive
U have used wrote a dual layer disk out with 0800 and inserting it into 360 for at least 5 seconds b4 turning on the pc ?

jameswalter · « **Reply #3 on:** November 05, 2006, 12:26:00 PM »

More info would help a lot. SATA chipset? How did you boot up, 360 first then PC, did you use the 0800 disc? What firmware are you using? Just give us more info.

blackpornstar · « **Reply #4 on:** November 05, 2006, 01:16:00 PM »

My mistake. I had my firware flashed to 4.2a xtreme. I tried botting up 360 first, then PC and vice-versa, but neither way reads my 360 drive. I was wondering if the fact that my PC doesn't have SATA would pose a problem, but thought that shouldn't be an issue. Or am I wrong in this instance? I don't have any SATA drives, so I'm a little slow in updating my system.

Also, I'm a little unsure of this 0800 disc you've referred to...

Thanks in advance...

This post has been edited by blackpornstar: Nov 5 2006, 09:17 PM

Romps · « **Reply #5 on:** November 05, 2006, 01:26:00 PM »

QUOTE(blackpornstar @ Nov 5 2006, 07:47 PM)

My mistake. I had my firware flashed to 4.2a xtreme. I tried botting up 360 first, then PC and vice-versa, but neither way reads my 360 drive. I was wondering if the fact that my PC doesn't have SATA would pose a problem, but thought that shouldn't be an issue. Or am I wrong in this instance? I don't have any SATA drives, so I'm a little slow in updating my system.

Also, I'm a little unsure of this 0800 disc you've referred to...

Thanks in advance...

How are u connecting the drive to your pc then ? sata to usb ?
and the 0800 img comes with the xtreme firmware it is needed to get the drive seen by windows and allso in your case since u had 4.2a flashed to it u will need it if u ever want to down/upgrade your drives firmware..

randreach454 · « **Reply #6 on:** November 15, 2006, 01:15:00 PM »

hey, hate to bump the thread again but im having probs with getting my windows to recognize my sammy too

heres my set up
via 8237 integrated sata(works great for flashing hitachis and sammys, ive done both now)
xtreme 4.2b
turn 360 on with sata connected to OFF computer, insert 0800 disc, then eject when my dashboard says open tray after reading it.
turn on pc, and here we are.

any help would be much appreciated!

jabroniekilla · « **Reply #7 on:** November 16, 2006, 09:49:00 AM »

enable0800.iso must be burned to a dual layer dvd+r that is it. that is your problem.

randreach454 · « **Reply #8 on:** November 16, 2006, 11:25:00 AM »

Actually i did burn mine onto a matrix dvd+r DL at 2.4x with clone cd on my pioneer 111d, just like i do with all my games...

Perhaps Ill try it with one of my verbs..

comradpoplin · « **Reply #9 on:** November 24, 2006, 02:16:00 AM »

verbs or infiniti are the safest bet

frankgomez75 · « **Reply #10 on:** December 22, 2006, 08:40:00 AM »

Did you ever solve this? I'm having problems trying to boot into windows.

Author Topic: Samsung Drive Recognition In Windows (Read 154 times)