Print

[utar]

I can guarantee you aren't still on 1888.  You are probably misreading the version.  If you post the entire version string from system information in the setup menus we can tell you which kernel you are using.


Utar

[dcaway]

err, as i eat my hat and remove my foot from my mouth, after just checking, it turns out that i am infact 7371... so much for that thought... damn you microsoft. sorry for the misinformation, wish i could edit that bad info out.

[sabbath_dude]

QUOTE(shrekan @ Sep 7 2009, 01:08 AM)

When you say almost all pre 83xx consoles are exploitable, what variants would prevent the few remaining from being exploited, general wear and tear, overheating etc?

I was referring to this......
http://www.xbox-scen...lAyCyTINZDx.php

[Bazdoctor]

Thanks to everybody involved in this, just got it to work, amazing stuff.

BTW, nice gamercard you have there sabbath_dude. Thats an interesting games list ( especially for a mod,  (IMG:style_emoticons/default/tongue.gif) )

This post has been edited by Bazdoctor: Sep 7 2009, 03:25 PM

[infidelity]

QUOTE(Martinchris23 @ Sep 6 2009, 03:58 AM)

To actually run the XeLL exploit, you MUST have the 3 x 330Ohm resistors connected. If you flash the XeLL exploit and don't have the three 330Ohm resistors connected, you'll get E79

Matrinchris23 - Question. I obtained "xenon_hack.bin (16.98kbs)" and I flashed it to my NAND with the infectus chip. Now, I don't have the 3 resistors installed, and when I turned on the 360, the green light would just sit there (no xbox 360 intro) for about 10-15 seconds, then I get the 3 RROD. So I decided to run to Home Depot and get the screws/washers for the X-Clamp fix just to play it safe. I've done this on other 360's and have gotten them to work.

So I did the fix, baked the machine, got the RROD down to 2 lights. Shut it off for about 30mins. Tried turning the 360 on (without the 3 330Ohm resistors again) and I just a black screen (no 360 intro), and then 10-15 seconds, I get the 3 RROD.

So 2 questions.

1. Do I have the correct .bin file? cause i searched through #xbins and I couldn't find "xenon_xell_hack.bin" i only found & flashed "xenon_hack.bin"

2. If I do have the correct file, than is it normal for the machine to produce the RROD, due to the 360 missing those 3 330Ohm resistors? or am I really supposed to have the 360 run the into and get that E79 error?

Many thanks.

[Relapse75]

QUOTE(infidelity @ Sep 7 2009, 12:06 PM)

Matrinchris23 - Question. I obtained "xenon_hack.bin (16.98kbs)" and I flashed it to my NAND with the infectus chip. Now, I don't have the 3 resistors installed, and when I turned on the 360, the green light would just sit there (no xbox 360 intro) for about 10-15 seconds, then I get the 3 RROD. So I decided to run to Home Depot and get the screws/washers for the X-Clamp fix just to play it safe. I've done this on other 360's and have gotten them to work.

So I did the fix, baked the machine, got the RROD down to 2 lights. Shut it off for about 30mins. Tried turning the 360 on (without the 3 330Ohm resistors again) and I just a black screen (no 360 intro), and then 10-15 seconds, I get the 3 RROD.

So 2 questions.

1. Do I have the correct .bin file? cause i searched through #xbins and I couldn't find "xenon_xell_hack.bin" i only found & flashed "xenon_hack.bin"

2. If I do have the correct file, than is it normal for the machine to produce the RROD, due to the 360 missing those 3 330Ohm resistors? or am I really supposed to have the 360 run the into and get that E79 error?

Many thanks. (IMG:style_emoticons/default/smile.gif)

WOW you don't READ the 3 330 OHM resistors are a MUST.  If not you will get the 3 red lights, just like you said. I hope you screwed your console up from baking it.  You obviously know about the 330 ohm resistors you just choose not to use them.  Since when did the real 3 RROD wait 10-15 seconds to show up, did you bother to flash the stock NAND back first?  Man people need to follow the tuts, and read what needs to be done. Just because you have an infectus doesn't mean you don't have to use the resistors.  If that was the case why wouldn't all that other console be hacked now, oh because they haven't released the points for the resistors.

[infidelity]

gee.... maybe if you read my original posts earlier in this thread, instead of going to the last page and seeing this post, and firing bull!@#$ at me, then you would realize my situation.

Hmm, strange how I asked this question to Matrinchris23, (since he is the one that has been in discussion with me over this issue), and not some newbie who signs up, and thinks he knows everything. If you want to write crap at me or others, make sure you read whats going on first before you write bull!@#$

As for the resistors, I read somewhere you only needed them if you were flashing the NAND without a modchip (ie Cygnos or Infectus)

This post has been edited by infidelity: Sep 7 2009, 06:14 PM

[Relapse75]

QUOTE(infidelity @ Sep 7 2009, 01:13 PM)

gee.... maybe if you read my original posts earlier in this thread, instead of going to the last page and seeing this post, and firing bull!@#$ at me, then you would realize my situation.

Hmm, strange how I asked this question to Matrinchris23, (since he is the one that has been in discussion with me over this issue), and not some newbie who signs up, and thinks he knows everything. If you want to write crap at me or others, make sure you read whats going on first before you write bull!@#$

As for the resistors, I read somewhere you only needed them if you were flashing the NAND without a modchip (ie Cygnos or Infectus)

Haha kid you call me a newbie but yet you most likely watch my youtube videos and followed my diagrams for this haha. Maybe you should realize who your talking too. You are some what right but mostly wrong, resistors are not needed for flashing, and it's best without them.  That is the 100 ohm resistors.  As with all the guides and tuts, the 330 ohm resistors are required. I don't have to read the previous post to understand what is going on, you say that you don't have the 330 ohm resistors, so plain and simple it's not going to work. If you don't want to belive me, that's fine, but without the 330 ohm resistors your going to get no where and just keep having a RROD console. Wow guess I'm not some newbie who just signs up eh?

And I'm such a noob that, the 1020x786RGB bin that you probably used from xbins was upped by me because noobs like you cant read directions and understand how to flash it in the correct blocks.

This post has been edited by Relapse75: Sep 7 2009, 07:38 PM

[shrekan]

QUOTE(Relapse75 @ Sep 7 2009, 07:22 PM)

Haha kid you call me a newbie but yet you most likely watch my youtube videos and followed my diagrams for this haha. Maybe you should realize who your talking too. You are some what right but mostly wrong, resistors are not needed for flashing, and it's best without them.  That is the 100 ohm resistors.  As with all the guides and tuts, the 330 ohm resistors are required. I don't have to read the previous post to understand what is going on, you say that you don't have the 330 ohm resistors, so plain and simple it's not going to work. If you don't want to belive me, that's fine, but without the 330 ohm resistors your going to get no where and just keep having a RROD console. Wow guess I'm not some newbie who just signs up eh?

And I'm such a noob that, the 1020x786RGB bin that you probably used from xbins was upped by me because noobs like you cant read directions and understand how to flash it in the correct blocks.

LOL relapse you're the biggest n00b going, thats why you got this snes emu at alpha and why you spent about 15+ pages on another thread helping all the "experts" with "expert" diagram schematics for both LPT and USB. Not to mention the videos you posted on youtube, yikes!!
We're all EXPERTS, lets go crazy    

QUOTE(sabbath_dude @ Sep 7 2009, 12:49 PM)

I was referring to this......
http://www.xbox-scen...lAyCyTINZDx.php

Sheesh, I completely forgot about that. thanks for reminding me, i got caught up in this homebrew hysteria.

[Relapse75]

QUOTE(shrekan @ Sep 7 2009, 04:51 PM)

LOL relapse you're the biggest n00b going, thats why you got this snes emu at alpha and why you spent about 15+ pages on another thread helping all the "experts" with "expert" diagram schematics for both LPT and USB. Not to mention the videos you posted on youtube, yikes!!
We're all EXPERTS, lets go crazy    

Never said I was an expert said I wasn't a noob, like you and that other bk.  IDK if u was being sarcastic or not but if u was then that was directed at u if not then my b.

[infidelity]

You can say whatever you want Relapse75. There was no need for you to attack me like you did ealier, when you *still* havent got the full story on my 360.

I don't care if your Xport, Dark-Alex, or any other major developer that uploads stuff for people to obtain and use. Plain and simple, read up on someones issue, before you start rambling/talking down to someone,  about stuff that you dont have all the facts on.

You've made it quite clear I need the resistors, I understand that. It's too bad that there's tons of misinformation out there.

So to anyone here in this thread, I have a question, what kind of 330ohm resistors do i need?

1/4 or 1/2 watt?

Thank You

This post has been edited by infidelity: Sep 7 2009, 10:36 PM

[Relapse75]

QUOTE(infidelity @ Sep 7 2009, 05:35 PM)

You can say whatever you want Relapse75. There was no need for you to attack me like you did ealier, when you *still* havent got the full story on my 360.

I don't care if your Xport, Dark-Alex, or any other major developer that uploads stuff for people to obtain and use. Plain and simple, read up on someones issue, before you start rambling/talking down to someone,  about stuff that you dont have all the facts on.

You've made it quite clear I need the resistors, I understand that. It's too bad that there's tons of misinformation out there.

So to anyone here in this thread, I have a question, what kind of 330ohm resistors do i need?

1/4 or 1/2 watt?

Thank You

I don't need the story to tell you the problem when you say that you didn't have the 330 ohm resistors. And I said that stuff because you knew about the resistors just choose not to use them, and when the exploit doesn't work you wonder why. And wattage shouldn't matter just dont go crazy with it, 1/4 will be fine, 1/2 would work as well, and even 1/8. I'm none of those people not even close, plus D-A is psp. There isn't really any miss info out there, just people don't read. Why do you think the zypher, falcon, and jasper haven't been released yet? Jasper is a little more difficult, but for the rest people need time to figure xenon out, as is it will be too difficult for the majority of the people so they're finding new points for the other boards.

[infidelity]

is there a certain method of getting these resistors to reach each point? I think i have just barely enough length in these to reach there points. I'll have to get some electric tape so they don't overlap and short out.

[shrekan]

QUOTE(Relapse75 @ Sep 7 2009, 10:24 PM)

Never said I was an expert said I wasn't a noob, like you and that other bk.  IDK if u was being sarcastic or not but if u was then that was directed at u if not then my b.

Soz relapse, it was sarcastic, no offence intended. Ive been following your advice on the other thread very closely and saw the video of the snes emu you posted a while back, and from what ive seen you're definately NOT a "newbie".
It just makes me chuckle that people think they are better because they have a higher post count.

BTW i hope you will be there to help when info for the jasper points are released, do you have a jasper ready and waiting?

[Relapse75]

QUOTE(infidelity @ Sep 7 2009, 06:17 PM)

is there a certain method of getting these resistors to reach each point? I think i have just barely enough length in these to reach there points. I'll have to get some electric tape so they don't overlap and short out.

What do you mean, u solder the resistor into the jtag point, then run a wire to the smc points. don't need tape or worry about over lapping.

And yeah I've got every version of board that I'll try this on, except for maybe an opus. I'll have to get a USB reader/writer before the jasper comes out, 256 and 512mb will take for ever over LPT.