Topic: Defective Xbox 360 ? (Read 4987 times)

michaelgg13 · « **Reply #795 on:** January 02, 2010, 12:47:00 PM »

im getting error 0001 when i turn it on i get the three red rings and the light on my psu stays orange but i hear its supposed to go green anyway. alsp the psu is fine ive used it on another xbox. any ideas how i could fix it?

michaelgg13 · « **Reply #796 on:** January 03, 2010, 06:26:00 PM »

anyone?

Silentblade4289 · « **Reply #797 on:** January 16, 2010, 08:49:00 AM »

Hello all, I got E 74 with the bottom right section of the ring flashing. Also got the secondary error code of 1022 for AV cable error.

So how likely is it that I just need a new AV cable and dont have my 360 off to microsoft?

hitcat · « **Reply #798 on:** January 16, 2010, 01:53:00 PM »

not very, I have a box with 1022 after x-clamp atempt by the owner, and two seperate av cables that work on my two boxes.

Silentblade4289 · « **Reply #799 on:** January 16, 2010, 02:31:00 PM »

QUOTE(hitcat @ Jan 16 2010, 03:53 PM)

not very, I have a box with 1022 after x-clamp atempt by the owner, and two seperate av cables that work on my two boxes.

Well, that sucks. I was hoping I just needed a new AV cable because I dont want to have to deal with Microsoft.

StOcKaBoi · « **Reply #800 on:** January 20, 2010, 08:27:00 PM »

hey i just xclamp fixed my xbox which had the 0102 error code. ive fixed several of these without any problems at all. after i did this fix i tried turning on the xbox to let it over heat and the power supply just shuts down and i get the 0003 error code...ive tried this power brick on my other xbox and it works fine.

any ideas of what might be the problem, and how i might be able to fix it?

its a jtaggable xbox so sending it in is the last thing i wanna do with this thing.

thanks guys

Stevie01 · « **Reply #801 on:** February 01, 2010, 01:21:00 AM »

Ive been trying to fix my xbox 360 for a couple days now. Ive done the penny trick, and cleaned the cpu and gpu. Then after i overheat my xbox and let it cool down it just goes right back to the 3 rings. Any help?

~sw~ · « **Reply #802 on:** February 10, 2010, 02:24:00 PM »

Hey guys,
My Xbox 360 has the 1, 2, and 3 red light error. (4 isn't on) When I power it on the fans go on for a second, but then do not work, and I do not hear any noise. I have tried the "Llama Mod", including the screws and the overheating, but nothing has happened.

Any insight to what the problem is?
Thanks,
Will

MadMaxGR · « **Reply #803 on:** February 11, 2010, 01:22:00 AM »

First you should post a new topic with your problem and not bring an old post to tell your problem... second you must provide the secondary error code so we can figure out what is wrong. Read the stickies to find out how to do it.

irulerockaway · « **Reply #804 on:** February 23, 2010, 10:47:00 PM »

i just got my buddys v2 360 that 3rrod code 0102 i let it heat up for 10mins no fans,then started it right away it worked for 5 hours then dashboard was freezing i turnd it off then back on boot screen froze giving 1(#4)red light with error code 1013,restarted it n got e79 error,restarted it n its workin 4 now i dont get wtf is wrong with this thing.u guys know what could be wrong with this?

MadMaxGR · « **Reply #805 on:** February 24, 2010, 01:07:00 AM »

QUOTE(irulerockaway @ Feb 24 2010, 07:47 AM)

i just got my buddys v2 360 that 3rrod code 0102 i let it heat up for 10mins no fans,then started it right away it worked for 5 hours then dashboard was freezing i turnd it off then back on boot screen froze giving 1(#4)red light with error code 1013,restarted it n got e79 error,restarted it n its workin 4 now i dont get wtf is wrong with this thing.u guys know what could be wrong with this?

Just a cold/bad solder under your GPU I pressume. The RROD will come back because you didn't reflow it as much as should be. But for now, it should be fine, it will last from 1 week up to few months maybe. Next time try Llama's method to reflow or , for more advanced fix, do a proper heatgun or reball fix.

ComputersForLess · « **Reply #806 on:** March 01, 2010, 05:01:00 PM »

QUOTE(Stevie01 @ Feb 1 2010, 04:21 AM)

Ive been trying to fix my xbox 360 for a couple days now. Ive done the penny trick, and cleaned the cpu and gpu. Then after i overheat my xbox and let it cool down it just goes right back to the 3 rings. Any help?

Please don't put pennies in your xbox's fellas. Geez....

irulerockaway · « **Reply #807 on:** March 01, 2010, 11:38:00 PM »

QUOTE(MadMaxGR @ Feb 24 2010, 09:07 AM)

Just a cold/bad solder under your GPU I pressume. The RROD will come back because you didn't reflow it as much as should be. But for now, it should be fine, it will last from 1 week up to few months maybe. Next time try Llama's method to reflow or , for more advanced fix, do a proper heatgun or reball fix.

well so far its working perfect,but a couple a things i noticed with the v2 is that it had that plastic around the edges of the cpu n gpu also noticed that it used 16.5 amps which my falcon used the same amount n its wierd seeing as that the v2 was manufactured around late 2006,n my falcon around late 2007.one more thing i did have to replace a couple of resistors under the cpu.i forgot to mention in the first past that it was also giving me e69 quite a few times even when the harddrive wasnt connected.

MadMaxGR · « **Reply #808 on:** March 02, 2010, 01:23:00 AM »

Seems like you messed up a lot with your console so far. When you get another issue next time, I recommend you to get it to a proffessional technician to fix it for you.

MetalMiketh · « **Reply #809 on:** March 14, 2010, 06:04:00 AM »

I had an error code 0102. I X-Clamped it. Now I'm getting error code 0020.

any ideas what could be doing this?

I made sure the bolts weren't over torqued.

Author Topic: Defective Xbox 360 ? (Read 4987 times)