Topic: Stop Messing Up Your Xgd3 Discs. Come Here To Burn Verify And Install (Read 59 times)

OggyUK · « **on:** October 24, 2011, 04:06:00 PM »

Lemon-/[email protected]

Lemon is a bot.

notta · « **Reply #1 on:** October 24, 2011, 08:09:00 PM »

QUOTE(Tilde88 @ Oct 24 2011, 10:08 PM)

Firstly, remember the EEPROM Utility you used? OPEN that sucker up again!
Go to the OPTIONS tab. Enable ALL options EXCEPT FOR OVERSPEED!
After each one, you will get a GREEN text saying Successful blahblah.
Exit. No need for reboot. These settings will stick even after PC off.

What is the EEProm Utility mentioned in this?

Tilde88 · « **Reply #2 on:** October 24, 2011, 08:26:00 PM »

QUOTE(notta @ Oct 24 2011, 10:09 PM)

What is the EEProm Utility mentioned in this?

It is located in the LTMAX package. Look inside the folders

Trooper2821438 · « **Reply #3 on:** October 30, 2011, 06:59:00 AM »

THANK GOD!!! someone else who uses TDK

I also attest to the fact that they are a good quality mate, and sweat by them... but ONLY the TDK brand.. other s04's really suck.. like memorex etc...

So Basically... are you saying that when I flash up to 2.0 and go to burn an image, all I have to do is play with the settings in imageburn like you have said, and then it will burn the iso properly?? or do I have to flash new firmware to my burner... I have been away from the scenbe for a while.. and im not sure what I should do RE the new XGD3 disks...

Cheers..

TPR

Trooper2821438 · « **Reply #4 on:** October 30, 2011, 06:59:00 AM »

THANK GOD!!! someone else who uses TDK

I also attest to the fact that they are a good quality mate, and sweat by them... but ONLY the TDK brand.. other s04's really suck.. like memorex etc...

So Basically... are you saying that when I flash up to 2.0 and go to burn an image, all I have to do is play with the settings in imageburn like you have said, and then it will burn the iso properly?? or do I have to flash new firmware to my burner... I have been away from the scenbe for a while.. and im not sure what I should do RE the new XGD3 disks...

Cheers..

TPR

g.hawk.360 · « **Reply #5 on:** November 15, 2011, 08:11:00 PM »

QUOTE(Trooper2821438 @ Oct 30 2011, 06:59 AM)

So Basically... are you saying that when I flash up to 2.0 and go to burn an image, all I have to do is play with the settings in imageburn like you have said, and then it will burn the iso properly??Cheers..

TPR

I realize i'm a bit late asking this but are you guys verifying the burns with nero at all? i can burn 100% of the iso perfectly in imgburn but then i get a disc quality of like 84 in discspeed. im burning with a mkm001 verbatim @ 2.4x (obviously). i havent yet tried increasing my buffer so ill have to try that next...

AarunJon · « **Reply #6 on:** November 16, 2011, 04:56:00 PM »

Try using IMGBurn instead to burn your backups.

And yes, with the XGD3 games it is highly recommended if not REQUIRED to verify your backups!!

Author Topic: Stop Messing Up Your Xgd3 Discs. Come Here To Burn Verify And Install (Read 59 times)