Print

[Psyfer9983]

Quick update. I found that the switch on the CR was set to slim, not phat. I know had it on phat after I soldered the CR and I think it may have switched to slim by accident when I moved it from my soldering station to my PC for programing and flashing of the CR and my nand (I was little distracted that day). I just seen this before I went to work this morning. I tried it again in phat mode, but the fans still do not work.

Could the CR being in slim mode cause damage to the fan header and/or controller?

Again, the console still boots to the stock dash with the CR in program mode. I haven't tried to boot xell since I found out that the CR was in slim mode. I may just solder a new header directly to the 12V on the bottom side of the power port so that the fans are at full speed and at least work.

[Psyfer9983]

Ok, so I just bypassed the fan header and went to a 12v pin on the bottom side of the power plug. The fans are now working and are running at 100% speed (that should help keep it cool   ).

Now I can't get the system to glitch. The green light on the CR will come on 5 to 10 times then stop like it glitched it but there is nothing on the screen nor the ring of light did it normal boot animation. Ideas?

[Psyfer9983]

Ok. I have try to glitch this all day and it will not work. Still boots with stock nand with the CR in program mode.

I'm now questioning J-Runner. Here is the my screen of J-Runner



Every time I read the nand, J-Runner wants to flash my CR with RGH 1, not 2.0. I know my dash is 14719, as you can see in the pic, but why is it also saying that I have 14699.

I'm sure I must use RGH 2.0 due to the dash being 14719. Do I need to use the old RGH to glitch this Zephyr console? If so, I will wire it up to use it.



Here is the log of the J-Runner pic.

CODE

===================================================
Saturday, May 05, 2012 6:39:18 PM

J-Runner v0.2 Beta (273) Started



Checking Files
Arm Version: 3
Flash Config: 0x01198010
Finished Checking Files
Zephyr
Reading Nand to D:\XBOX 360 FIXES AND MODS\RGH Tools\J-Runner v02 (271) Core Pack\output\nanddump1.bin
Reading Nand
Done!

Reading Nand to D:\XBOX 360 FIXES AND MODS\RGH Tools\J-Runner v02 (271) Core Pack\output\nanddump2.bin
Initializing Nand..
Reading Nand
Nand Initialization Finished
Done!

Comparing...
Nands are the same
Programming Coolrunner
Flashing D:\XBOX 360 FIXES AND MODS\RGH Tools\J-Runner v02 (271) Core Pack\common\xsvf\TX_RGH2_C.xsvf to CoolRunner
Input Filesize: 593E
Output Filesize: 2C7E
Done!


Exited!

* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
 * we found the following parts:
SMC: 1.10
CB_A: 4575
CB_B: 4575
CD (image): 4575
CD (decrypted): 9452
 * checking required versions...
ok
 * patching SMC...
Patching Zephyr version 1.10 SMC at offset 0x1257
 * Replacing CD...

* XOR HACK NEEDED FOR CB 4575
 * patching CB_B...
patchset for 4577 found, 4 patch(es)
 * Applying XOR Hack to CB_B 4575
 *** Re-encrypting CB_B with xor keystream
 *** Fixing entrypoint
 * Replacing CB_A 4575 with 4577
 * encrypting CB...
 * constructing new image...
 * base size: 70000
 * No separate recovery Xell available!
 * Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 4577
0x9AC0..0x11D1F (0x8260 bytes) CB_B 4577
0x11D20..0x17D1F (0x6000 bytes) CD 9452
0x17D20..0xBFFFF (0xA82E0 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
 * Encoding ECC...

100%
------------- Written into output\image_00000000.ecc
Arm Version: 3
Flash Config: 0x01198010
Writing Nand
Done!

[Psyfer9983]

Crap, the pic got resized. Try this one.

[Psyfer9983]

Never mind. I got my Falcon working and have returned the Zephyr to stock. I soldered in a wire for 12v to the fans so that they will work. I my drop the voltage down to 8 or 10 volts so that the fans are not as loud but still move plenty of air.

[highonxbox]

I'm having this exact problem (minus the fans thing).

I can't get the zephyr to glitch. I was also using jrunner. Maybe I'll try a different guide.

I have a CR REv B and Nand-X