xboxscene.org forums

Pages: 1 ... 4 5 [6] 7 8 ... 13

Author Topic: Lite-On 83850c Hardware and Software Support Thread  (Read 714 times)

GrandPipe

  • Archived User
  • Newbie
  • *
  • Posts: 11
Lite-On 83850c Hardware and Software Support Thread
« Reply #75 on: October 01, 2009, 09:20:00 PM »

Hi. having a problem trying to flash a new liteon. I was able to do a 8385c FW liteon this morning no problem. Used the exact same method with a 2nd one and i keep getting an error when trying to extract the firmware.

It recognises the drive, i click LO83info button and use the tray half open trick. Click ok and then it asks to open the tray fully which i do. Clicked OK then it thinks for a bit and gives me a "LO83info extraction Failed!" error (log below).

any advice? unsure what it could be. Using the latest version of JF, VIA card for sata and xtractor connectivity kit to power. It worked on the previous xbox but now im having this problem.


~~~~~~~~~~~~~~~~
JungleFlasher 0.1.66 Beta
Session Started Fri Oct 02 12:13:56 2009

This is a 32 bit process running on 2 x 32 bit CPUs
PortIO is installed and running.
Found 4 I/O Ports.
Found 2 Com Ports.
Found 6 windows drives A: C: D: E: F: G:
Found 2 CD/DVD drives E: F:

Sending LO83info request to I/O port 0xD000

............
................
0000: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0010: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0020: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0030: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0060: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................


LO83info extraction Failed!
Logged

jivemm

  • Archived User
  • Newbie
  • *
  • Posts: 7
Lite-On 83850c Hardware and Software Support Thread
« Reply #76 on: October 01, 2009, 10:46:00 PM »

I'm having the same problem. Experienced with modding all drive types, have had no problems with LiteOns and have flashed a 83850c with no problems. But now one with the 0's and failed at the same spot.
Logged

dirkajihad

  • Archived User
  • Newbie
  • *
  • Posts: 17
Lite-On 83850c Hardware and Software Support Thread
« Reply #77 on: October 02, 2009, 09:21:00 PM »

You need to power cycle the drive in between when going from half to open tray.  Make sure to read the JF instructions and follow them to the tee and you won't have any issues.

Basically, open with half tray, power cycle, click ok, open full tray, click ok, open/close to half tray again, power cycle again, click ok, open to full tray again, click ok.

If you do that, it should extract the key just fine.

This post has been edited by dirkajihad: Oct 3 2009, 04:25 AM
Logged

kiwimods

  • Archived User
  • Full Member
  • *
  • Posts: 145
Lite-On 83850c Hardware and Software Support Thread
« Reply #78 on: October 03, 2009, 08:09:00 AM »

QUOTE(GrandPipe @ Oct 2 2009, 04:20 PM) View Post

Hi. having a problem trying to flash a new liteon. I was able to do a 8385c FW liteon this morning no problem. Used the exact same method with a 2nd one and i keep getting an error when trying to extract the firmware.

It recognises the drive, i click LO83info button and use the tray half open trick. Click ok and then it asks to open the tray fully which i do. Clicked OK then it thinks for a bit and gives me a "LO83info extraction Failed!" error (log below).

any advice? unsure what it could be. Using the latest version of JF, VIA card for sata and xtractor connectivity kit to power. It worked on the previous xbox but now im having this problem.
.
0040: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0050: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
0060: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
LO83info extraction Failed!

If the drive has a august manufacture date on it then this is your problem:

http://forums.xbox-s...howtopic=692490
Logged

KingKapalone

  • Archived User
  • Newbie
  • *
  • Posts: 10
Lite-On 83850c Hardware and Software Support Thread
« Reply #79 on: October 06, 2009, 02:36:00 PM »

Is there a step by step guide on how to flash the 83850c? I can't seem to find one that covers all steps. I don't really know what to do in terms of connecting it to the computer and powering it up. Then it would be nice if the guide continued.

I also have a manufactured in August drive, so I'm not even sure if it will work.

I also see on the Jungleflasher page on 360Mods that it doesn't work in 64-bit Windows. Is that true?
Logged

halleluia

  • Archived User
  • Jr. Member
  • *
  • Posts: 77
Lite-On 83850c Hardware and Software Support Thread
« Reply #80 on: October 07, 2009, 09:39:00 PM »

I have a Intel G31PR mobo and according to Wikipedia it has a ICH7 southbridge...I have successfully flashed Samsung and Hitachis but does my mobo support Liteons??
and

Under drive configuration ATA/IDE mode is set to native should I change it or not??
Logged

GreaT

  • Archived User
  • Newbie
  • *
  • Posts: 7
Lite-On 83850c Hardware and Software Support Thread
« Reply #81 on: October 08, 2009, 11:20:00 AM »

Please someone help me!

I was an asshole when i erased my 83850c after the 288bytes key dump.
Someone can decrypt the 288byte dump for me?

Or the Jtag rom reading is the only solution?


Thank You,


Logged

kondud

  • Archived User
  • Newbie
  • *
  • Posts: 2
Lite-On 83850c Hardware and Software Support Thread
« Reply #82 on: October 08, 2009, 03:45:00 PM »

I greet all.
I am from the Poland and this is the text from the translator. I have the quite atypical problem. Namely was I reading the key Liteona 8385 the programme JungleFlasher 0.1.66beta and was I using power supply the console. I tried first to read the key single - time switching off reinforcing from the drive in the moment of closing and connecting him to the computer and then hand closing and opening klapki, but it was not successful to read the key.
I then already switched off power supply 2 some read times and key oneself, I hope that good, but there is no certainty to puki here he will not test him in some drive. But drive and console oddly behave now, namely the diode Power winks the whole time after the inclusion the console and he opens the drive alone if I try him to close this is closes on the moment and again opens. If I switch off the console the button power the drive is closes and opens with the return and the console one switches off with the open klapką of the drive.
I will add that I did not erase the firmwaru of the drive and did not in this new and did not even connect the cable sata from the console because I do not know as this will end.
What did I make and or this will give oneself to come unscrewed?
Logged

fitsman

  • Archived User
  • Full Member
  • *
  • Posts: 104
Lite-On 83850c Hardware and Software Support Thread
« Reply #83 on: October 09, 2009, 12:18:00 PM »

Does anyone try to dump - flash the new liteon fw-83850c with dosflash 1.8 and firmtool in clear dos?

If it did then which is exactly the procedure to dump correctly the key with dosflash 1.8 in clear dos?
Simply run the dosflash 1.8 with the tray of the liteon fw83850c half open and then you do full open tray without close the power of the drive?

Which is the correct procedure of dumping the liteon fw-83850c firmware in clear dos(Not in any windows)

A lot of thanks.
Logged

kondud

  • Archived User
  • Newbie
  • *
  • Posts: 2
Lite-On 83850c Hardware and Software Support Thread
« Reply #84 on: October 09, 2009, 01:25:00 PM »

Thank you for the answer. What I understand unfortunately not very much I have to do. I know English faintly and use the translator that is why. If this possible, write this I ask the simpler language.

First translator:
I greet again from the Poland. I described all from the beginning. I read the key from drive DVD. I used power supply the console. I disconnected two times while reading the key power supply from drive DVD. Dodge it was successful to read. I already have new ready firmware to the drive. I did not install him yet because I have the problem.
If I switch off the console this opens drive DVD and becomes so, in the open position. And 2 are cases now:
1.. If I turn on the console the button „Power” this is closes the drive first and he opens then alone. He so already becomes. „Opening”is shows at the TV. The diode „Power”winks the whole time.
2.. If I turn on the console the button „Eject” this is closes the drive. He is at the TV „Unlock the drive”. The diode „Power”winks the whole time.

What oneself could stand?

Second translator:
Hello again from the Polish. I described everything from the beginning. I read the key from the DVD drive. I used the power of the console. While reading the key twice disconnected power from the DVD drive. The key could be read. I have already finished a new firmware to the drive. Not yet Uploader because I have a problem.
If you turn off the console that opens the DVD drive and so is, in the open position. And now there are 2 cases:
1. If I turn the console by pressing the "Power" is the first drive and then closes itself opens. Already is. On TV shows are "Open". All the time blinking LED "Power".
2. If I turn the console by pressing the "Eject" the drive is closed. On TV is "Open Drive". All the time blinking LED "Power".

What oneself could stand?
Logged

Coldblackice

  • Archived User
  • Newbie
  • *
  • Posts: 3
Lite-On 83850c Hardware and Software Support Thread
« Reply #85 on: October 09, 2009, 04:08:00 PM »

ahhh dog crap. i got a new xbox elite, cracked it open, and without thinking, started probing the crap out of it to get the key (as I've done with many xboxs before).

of course jungleflasher (1.62, old version) kept telling me bad serial data. when i go to update jungleflasher, i see 8353c drive support. i realize thats the drive i have. then i see that theres a new way to flash it, and that using the probe can DAMAGE THE DRIVE.

how can i tell if ive damaged the drive? i used a homemade usb xtractor. i suppose i should just go ahead and try the next step of trying to flash it properly, and see if its damaged from there. i just wanna make sure that i dont damage it further.

any thoughts? anyone had experience like this?

thanks
Logged

SNAAAKE

  • Archived User
  • Hero Member
  • *
  • Posts: 656
Lite-On 83850c Hardware and Software Support Thread
« Reply #86 on: October 10, 2009, 07:39:00 PM »

same question as the dude above above(lol). is there a way to flash this in dos? I cant get windows to recognize this new liteon(I always used dos before). I tried the 6321l card and onboard sata but no luck. messing with things in windows always seemed rather risky(random freeze=bricking stuff).
Logged

mattahammond

  • Archived User
  • Newbie
  • *
  • Posts: 11
Lite-On 83850c Hardware and Software Support Thread
« Reply #87 on: October 10, 2009, 09:35:00 PM »

I have a 7-7-2009 MFR date with the 83850c and everything went well. I was wondering since I am new to this how long with this last before xbox bans us all? I heard there is a new console update coming out this month to inter grade facebook and such. Will there be more firmware updates and such? How will xbox detect our firmware upgrade in the future? Thanks.
Logged

mattahammond

  • Archived User
  • Newbie
  • *
  • Posts: 11
Lite-On 83850c Hardware and Software Support Thread
« Reply #88 on: October 11, 2009, 12:52:00 AM »

Success on my buddies drive! smile.gif
Logged

Stealth51

  • Archived User
  • Newbie
  • *
  • Posts: 1
Lite-On 83850c Hardware and Software Support Thread
« Reply #89 on: October 11, 2009, 06:40:00 PM »

Ok so I am attempting to flash my lite-on 83850c drive with jungleflasher. I am using my XBOX 360 to power the drive and connecting it directly to my onboard sata, which is compatible. I am experiencing the Extract no.2 doesn't match! Aborting! LO83info extraction Failed! error. The problem is when i try to close the drive halfway the second time my computer crashes to blue screen when i remove the power cable from the drive. However the lines of code comes up and i get the "in dedication string" message. I just can't get any further than this because of my computer. Does any one know how to fix this problem?
Logged
Pages: 1 ... 4 5 [6] 7 8 ... 13