Print

[murdock2577]

QUOTE(antispimmer @ Jun 9 2009, 07:06 PM)

Nice video. I followed everything he said until he ran l-o-eras.exe in dos, but now I'm getting status FF00. That's different than what I was getting, but I'm still not sure what that means.

dude stop making the liteon cry....enough with the erases  (IMG:style_emoticons/default/smile.gif))) just kidding... but seriosly its not the erasing problem..      if you managed to boot to dos do a power cycle after it booted the type dosflash ..it will find your drive in status...hope its a good status...   then hit W(write)   enter the firmware you want to write.. it should work

[antispimmer]

I was finally able to get it to work! I'm not entirely sure why the drive wasn't being recognize after it was erased when it had been before, but by switching the drive to a different SATA port I was able to get it to show up in DosFlash. It was a pretty simple process from there.

Thanks a ton, everyone.

[murdock2577]

QUOTE(antispimmer @ Jun 9 2009, 09:04 PM)

I was finally able to get it to work! I'm not entirely sure why the drive wasn't being recognize after it was erased when it had been before, but by switching the drive to a different SATA port I was able to get it to show up in DosFlash. It was a pretty simple process from there.

Thanks a ton, everyone.

Lameoo   all this fuss over a bad sata port =))     how could i not think of that...   well glad to hear you solved it (IMG:style_emoticons/default/biggrin.gif)

[sniffles]

QUOTE(headonism @ Jun 9 2009, 03:12 PM)

if you have a 512k memstick then put iprep onto this also you want to add l-o-eras and dosflash (the latestversion)...... you are now gonna need to put your lite_CFW.bin onto the stick, once you have these reboot yyou sysem then look for boot options u can genrally find these in you bios setup or by hitting f8.

if you find this in bios setup then tell it to look for your mem stick as first boot or priority boot

once you have done this load iprep but dont use it, just type l-o-eras port (PORT being your port key so dont just type port)
tou should return with ff80 do this about twice then power cycle your dvd try again about twice then you should get ff72

once this is done..... type dosflash

this will ask you if you want to send mtk or some shit just hit N

you will now be asked where is your drive mine is located on no. 6 if the same then just hit 6 and enter

now this is the fun part ...... you will get several options choose liteon E this will erase the drive again

once this has finshed

run dosflash again.... follow the earlier steps till you get to the options again this time you want to write you firmware so you should hit W

it will ask you where to find the firmware... provide you put your custom firmware onto you stick then type

lite_cfw.bin this will now write the firmware....

we are all done now restart you computer and put your drive back in your box

hope this helps

I just want to say Thank You!  These instructions worked perfectly for me after I thought I bricked my 83850c.

Just to clarify for anyone who reads this, my Xbox began only having a blinking green light and I had no eject capabilities after erasing the drive in JungleFlasher and managing to not power cycle quick enough.  Then my BIOS wasn't detecting the drive.

I followed your instructions above and made sure to SWITCH MY SATA PORT and POWERCYCLE the drive (that was VERY important to get DOSFLASH to see it).  Now I have a totally functional ix1.6 flashed 83850c.

Again, thank you.  You've saved my arse!

[Denhoorn]

Edit: Nevermind, problem solved I see (IMG:style_emoticons/default/smile.gif)

This post has been edited by Denhoorn: Sep 20 2009, 01:01 PM

[jodm]

QUOTE(antispimmer @ Jun 9 2009, 05:06 PM)

Nice video. I followed everything he said until he ran l-o-eras.exe in dos, but now I'm getting status FF00. That's different than what I was getting, but I'm still not sure what that means.

antispimmer, My driver is a Lite-on 93450c and when I click to erase it, a always have return 0x80, after a lot of tries I discover one way to "unlock" and erase the Liteon Driver, try this, for me it's work:

1) turn off your driver;

2) open jungle flasher;

3) Make sure that your driver is in a correct port, for you is 0xCC00 correct?;

4) then click ERASE LITE-ON, you should see the return 0x7F,something like this:

---------------------------------------------------------------------------------------------------------
         
Sending Lite-On-Erase request to port 0xCC00

..............

Drive returned Status 0x7f

..............

Device Intro failed!

---------------------------------------------------------------------------------------------------------

 

5) Ok, now click ERASE LITE-ON again but now, after the messenger "Drive returned Status 0x7f" turn on your driver while (...) the dots is being show.

6) After you turn on you driver(step 5), I wait your driver return "Drive returned Status 0x72" the correct status(Erased).

Good Luck,. =)..

[grassy84]

QUOTE(jodm @ Dec 20 2009, 01:49 PM)

antispimmer, My driver is a Lite-on 93450c and when I click to erase it, a always have return 0x80, after a lot of tries I discover one way to "unlock" and erase the Liteon Driver, try this, for me it's work:

1) turn off your driver;

2) open jungle flasher;

3) Make sure that your driver is in a correct port, for you is 0xCC00 correct?;

4) then click ERASE LITE-ON, you should see the return 0x7F,something like this:

---------------------------------------------------------------------------------------------------------
         
Sending Lite-On-Erase request to port 0xCC00

..............

Drive returned Status 0x7f

..............

Device Intro failed!

---------------------------------------------------------------------------------------------------------

 

5) Ok, now click ERASE LITE-ON again but now, after the messenger "Drive returned Status 0x7f" turn on your driver while (...) the dots is being show.

6) After you turn on you driver(step 5), I wait your driver return "Drive returned Status 0x72" the correct status(Erased).

Good Luck,. =)..

You say that you always get ox80 however you have 0x7f in the status when the drive is off? I always recieve 0x80 both in dos (when drive has power only) and in jungle flasher (regardless of whether the drive has power to it or not) Have dosflash 1.7, tried various drivers or no driver for via PCI card and still no luck. Tried power cycling and l-o-erase ad naseum. Any other ideas?

This post has been edited by grassy84: Dec 20 2009, 01:28 PM

[lotech]

QUOTE(headonism @ Jun 10 2009, 03:12 AM)

we are all done now restart you computer and put your drive back in your box

hope this helps

Thanks, this was super useful. I knew I hadn't bricked it but was having a hell of a time getting the fw to actually write. I think the current version of Jungleflasher is a bit buggy. I can't open it with the newly flashed drive attached (crashes), if I start the drives power after loading JF it gives me errors with the apps code and inevitably crashes. The drive works fine in my xbox however.

[Shane1027]

QUOTE(jodm @ Dec 20 2009, 04:49 AM)

antispimmer, My driver is a Lite-on 93450c and when I click to erase it, a always have return 0x80, after a lot of tries I discover one way to "unlock" and erase the Liteon Driver, try this, for me it's work:

1) turn off your driver;

2) open jungle flasher;

3) Make sure that your driver is in a correct port, for you is 0xCC00 correct?;

4) then click ERASE LITE-ON, you should see the return 0x7F,something like this:

---------------------------------------------------------------------------------------------------------
         
Sending Lite-On-Erase request to port 0xCC00

..............

Drive returned Status 0x7f

..............

Device Intro failed!

---------------------------------------------------------------------------------------------------------

 

5) Ok, now click ERASE LITE-ON again but now, after the messenger "Drive returned Status 0x7f" turn on your driver while (...) the dots is being show.

6) After you turn on you driver(step 5), I wait your driver return "Drive returned Status 0x72" the correct status(Erased).

Good Luck,. =)..

you are a lifesaver!! Thank you so much, I was freaking out about bricking my friends drive!