Print

[AnimeCommander]

Just an FYI: Those that get the DKU-5 Cable with the rubber casing around the USB end and the hard case/epoxy underneath, try the blue wire. I just was able to get my Lite-on's key with it.

I thank all those that put this idea together. You've saved me spending more money as I just happened to have the DKU-5 cable from an old phone I had some years ago.

[Late]

Hi, I was looking for some help with a dku-5 cable I just purchased.  eBay link:http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280410342400&ssPageName=STRK:MEWNX:IT

I opened it up and there arent any regular labels, they all say r#

There are 3 wires attached to the board, white, black, and blue.  the white wire goes into point r12, the blue goes into one near the end towards the wire (not usb) and the black one is a little bit more towards the usb.  When i use realterm, I get the rxd to light up when i put my finger on the black and blue wire together.

Was lookin for a little help on how to figure out which wire to connect to the needle

Thanks

heres a picture:
http://i38.tinypic.com/iw4vls.jpg

edit: actually the above post is what I needed I think, I'll try that out.

This post has been edited by Late: Nov 3 2009, 05:07 AM

[shitface420]

hey i just got a dku-5 usb cable and i was just woundering exactily how to check/test if i set it up right??

do i need to hook up a gnd wire?

im not to sure which wire is the Rx and i dont wanna mess anything up yet lol so please help

[dvs1]

i have this cable it does seem like the right kind.  can anyone confirm for me? http://pinouts.ru/Ce...60_pinout.shtml

[Datenshiz]

Images of my cable PCB are LARGE:
OTIchipUP
OTIchipUP

As you can see, my RX wire is blue and is the one i connect to the Xbox. Yours might be a different color.

This post has been edited by Datenshiz: Nov 23 2009, 11:06 PM

[shitface420]

I just need to know how to check my wire in Realterm....

like what do all the settings have to be at so i can see if i can get some loopback....

do i need any other drivers for the wire itself?

which program do u think is the best choice Realterm, hyper terminal, or the other one i cant think of  

[Datenshiz]

Just connect RX and TX wire then open hyperterm and type something random and send it, you should receive an identical message back.

[ImRickJamesB1tch]

Again to sum this 20 page topic up. All you need to dump the lite-on 74xxx key is the following:

1> Running Windows XP.

2> Buy this CABLE:

CODE

http://cgi.ebay.com/CA-42-USB-CABLE-FOR-NOKIA-6100-5070-6070-6102i-6015i-UK_W0QQitemZ350221720812QQcmdZViewItemQQptZUK_MobilePhones_MobilePhoneAccesories_MobilePhoneDataCables_JN?hash=item518ad75cec

3> DRIVER

CODE

http://www.tiaowiki.com/download//file.php?id=6

4> A safety pin.

When you get your cable, cut the connector off that connects to the phone..Cut the outer black plastic about 5cm and cut the blue and green wires off. You don't need them. Only need the white one for this specific make and model from this seller.

Strip the wire and wrap it around the safety pin and you done. Install the driver, plug the cable in and dump away



Yeah it doesn't look fancy but it works. Once you got it working you can make it look pretty. Hope it helps  

[TS_]

Thought this might help someone.

(IMG:http://personal.inet.fi/cool/mediatek/programs/images/phone_connector.gif)

[midhet]

QUOTE(n99wby @ Sep 20 2009, 06:16 AM)

I got the exact same calbe but I cant seem to get it to work....

In RealTerm which i never used before when connected it shows BREAK as red, should it do that? I cant seem to get any RX on it just TX flashing yellow....

Any help you can offer?

any solution to this problem? i have a ca-42 cable with 5 wires ... white, orange, green, blue, black, the pcb doesnt have numbering for rx ... i also get BREAK in realterm and hyperterminal says that it cannot open the port. tried all combos of wires twisted in realterm but no use ... even took a gamble and tried to extract the key using the green wire but jungleflasher gave me the bad serial data error

[Datenshiz]

Don't know how to resolve that problem, with the BREAK thing that is. Either way, randomly connecting the wires is not that good of a move, its likely to damage your cable and/or USB port, because one of the wires may contain USB voltage.

What you can do is check the PCB on the cable, trace the leads to the chip that has a name and modell written on it, look it up on google and see if you can find which of its legs is RX. Then trace that leg to the correct wire.

[midhet]

QUOTE(Datenshiz @ Dec 15 2009, 06:18 AM)

What you can do is check the PCB on the cable, trace the leads to the chip that has a name and modell written on it, look it up on google and see if you can find which of its legs is RX. Then trace that leg to the correct wire.

its a generic looking pcb (one of those knockoff cables i think, still cost me 8 bucks) with gt50727 written on it, the two chips themselves have nothing written on them

[jview]

ImRickJamesB1tch thats a big pic, lol ,..

people if your still have problems look at my posts in this THREAD,.. i used a clone dku5 cable and it worked, still working till this day,.

[snoopyteam1]

Any solution?

[distort1]

QUOTE(midhet @ Dec 14 2009, 11:10 PM)

its a generic looking pcb (one of those knockoff cables i think, still cost me 8 bucks) with gt50727 written on it, the two chips themselves have nothing written on them

This cable works you just need to rewire it. at the three pins on the bottom the one on the left side is the one you should be using