Print

[chomnom]

QUOTE(mrblobby501 @ Jul 17 2009, 10:32 PM)

Thanks for the advice, but I already tried that. I can get it erased and then go into dosflash, but the flashing routine always hangs during flashing of the first bank. I just flashed another Lite-on with no problem in Jungleflasher (HW ver A0A1). My "problem" drive is HW ver A0A2.

did you ever fix this? my drive hangs at writing bank 0 in dosflash too.  been frustratin me for weeks.

[bb90]

Thank you for this. I never flashed a liteon before, and fked up with erasing it. My computer didnt freeze, i just had trouble cycleing the drive and then decided to hit ATA reset, Bad idea...

Anyways it worked great and my drive is properly flashed now.

Thanks again!

This post has been edited by bb90: Oct 22 2009, 11:13 PM

[ltrover]

QUOTE(UMDJ @ Oct 3 2009, 08:19 PM)

just load the lite on dummy key into jungle flash, and spoof to ben q 1.6 fw, then follow regular procedures for ben q flashing...

but to my problem though. i erased my lite on, then i flashed it to 1.6, and now it wont read back ups or originals. and its a brand new xbox 360. i erased and reflashed to 1.5, and it didnt work. any idea why? the laser still lights up properly. and the disc spins(only for a sec), its not a bad key because i spoofed the the lite on to a sammy. i even did a pot tweak with no change in results

I've got exactly th esame problem. Anyone know a solution for this?

I originaly tried flashing my new liteon 830850c drive ( I have successfully flashed lots of other types of drives with no problem) using JF, after erase during write my pc froze locking drive in vendor mode. I tried everythng I have read in this forum to get the firmware wrote to the drive, but no luck at all! I then sent my drive to a reputable flasher/repairer of 360s of another forum. They said they had successfully flashed the drive with IX1.6, but when I put it in the 360 it wont read any disks. No error lights, or error codes. The drive spins, it says reading on the screen, then nothing.

Anybody help?

[Soulja85]

When i boot from usb i get the message 'remove all drives and disks, press any key to restart' have i not got the proper dos on or something?

[donhu]

hey guys i really need some help.... so... i tried to flash a 83850c drive and didnt check the dummy.bin that i created to see if it was "good" before i went ahead with the rest of the process and so i ended up erasing the drive and not having a "good" dummy.bin to finish the process. so now im stuck with a dead drive and no dummy.bin to work from (becuz the drive is erased) what can i do to get my drive back up and running (i.e. flashed)?




thanx

[amp2006]

QUOTE(donhu @ Nov 6 2009, 06:48 AM)

hey guys i really need some help.... so... i tried to flash a 83850c drive and didnt check the dummy.bin that i created to see if it was "good" before i went ahead with the rest of the process and so i ended up erasing the drive and not having a "good" dummy.bin to finish the process. so now im stuck with a dead drive and no dummy.bin to work from (becuz the drive is erased) what can i do to get my drive back up and running (i.e. flashed)?
thanx

i had the same problem but i had the valid keys (dummy.bin)

since i also erased coudnot write it due to my Via sata raid .issues

i ended up to use Iprep to write the keys to flash the drive but mine was 74850c

here is what i did :

i have used JF latest one + after i got a valid keys with 360 xtraxtor Pro  

open source firmware (dummy.bin)
open target firmware (ix1.6-liteon)

and then Save to File Lite_CFW

and then i used Iprep to make a bootable USB Drive

and deleted the L74CFW in CFW folder created by iprep and put the Lite_CFW and renamed to L74CFW

and also created a folder inside BACKUPS named 1234567 and a folder named 12345 and put it the L74CFW inside 12345

BACKUPS >>1234567 >>12345

and then i used iprep 10.7 to write the flash .

c:\>l74 1234567 12345 w

and it flashed and done ..


hope you have a good valid keys


but from question no keys no work .i think

[pwedkc]

Hi, I also have the problem of it playing no backups or originals. Laser was tweaked too and still no go. Key was spoofed to another Lite-On and it didn't work. Key was spoofed to a BenQ and it works. Help?

[jdog7765]

I know this Sticky is old, but I'm having trouble with my Liteon. I was able to dump all the files compile the firmware. Did the Liteon erase, but wasn't quick to reset the drive and drive did not go into vendor mode. So i followed all the tutorials I could find and did the L-O-Eras and got FF72 but when I use dosflash I don't see the drive listed under option 5 0xC800, it says no ATAPI device found. If I don't use the loeras and just go straight to dosflash it asks if I want to send drive intro. I say yes, reset drive but that doesn't work. Has anyone else had this issue. I cant figure it out.

Thanks

[amp2006]

QUOTE(jdog7765 @ Dec 28 2009, 06:59 AM)

I know this Sticky is old, but I'm having trouble with my Liteon. I was able to dump all the files compile the firmware. Did the Liteon erase, but wasn't quick to reset the drive and drive did not go into vendor mode. So i followed all the tutorials I could find and did the L-O-Eras and got FF72 but when I use dosflash I don't see the drive listed under option 5 0xC800, it says no ATAPI device found. If I don't use the loeras and just go straight to dosflash it asks if I want to send drive intro. I say yes, reset drive but that doesn't work. Has anyone else had this issue. I cant figure it out.

Thanks

here if you have a 74850c


open Jungleflasher go to Firmware Tool 32 and then :

open source firmware (dummy.bin)
open target firmware (lite-on 1.6)

and then Save to File Lite_CFW

 then use Iprep ( latest one) to make a bootable USB Drive

and delete the L74CFW in CFW folder created by iprep and put the Lite_CFW and rename it to L74CFW

and also create a folder inside BACKUPS name it 1234567 and a folder name it 12345 and put it the L74CFW inside 12345

BACKUPS >>1234567 >>12345>>L74CFW

after all done restart the PC and then boot from a usb drive and then just type this after you clicked on YES button for a risky message :


l74 1234567 12345 w

it will ears the drive now and after that it will ask you to turn off the drive power and back it again .and it will ask you to press any key and after you pressed the key the writing will be done

[jdog7765]

Well, after messing around with what you posted for an hour, I finally tried a few other things. I used another sata port on my motherboard and went back to jungle flasher erased and sent intro an worked perfectly; flashed and all. Thanks for the reply though!!

[nhoj_yelbom]

thanks helped a bunch, and i found this by the search function!!!!

[jackblock]

I am using a liteon 74850c and going from 1.6 to 1.61, I have done many flashed including another 7 series liteon from 1.6 to 1.61 this one is just giving trouble I guess
I have correctly extracted the key and created the custom FW. The first time that I tried and flash the new FW the verify failed so I tried to just erase and flash again, but comp restarted. Since then I have not been able to get it back in vendor mode.
I have been reading many posts on remedies to get back in vendor but I can’t get it. Everything I have read says that the drive isn’t bricked so I am set on getting it working.

I have tried over and over in JF to get it in vendor, constantly get 0x80, 0x51, 0x50, and 0xD0 statuses.

I have also created a boot floppy with l-o-eras.exe dosflash and my custom FW. Have been trying to erase the drive from dos and constantly get FF80 status, I know that I am using the right sata port.

My only questions are what to try next; I am using the ck3 pro with usb. While I am trying to get it into vendor do I need to have the usb wire connected also?

Any help would be appreciated

This post has been edited by jackblock: Jan 5 2010, 06:32 PM

[PhoneyVirus]

While I am trying to get it into vendor do I need to have the usb wire connected also?

No and you might need that USB Driver installed I used the Serial knowing that USB needs a driver installed where Serial is always installed if you got one. Also with Liteon drives the Original firmware can't be Restored so theres no going back when you flash your Liteon drive.


This post has been edited by PhoneyVirus: Jan 10 2010, 01:36 AM

[jackblock]

ended up just swapping drives, everything works now

[njmbb8]

can anyone tell me if my drive is too bricked for this its an 830850c it wont eject and isnt detectable by jf

heres the log file:

CODE

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~

JungleFlasher 0.1.70 Beta

Session Started Tue Feb 02 13:54:00 2010



This is a 32 bit process running on 8 x 32 bit CPUs

portio32.sys Driver Installed

portio32.sys Driver Started, thanks Schtrom !

Found 6 I/O Ports.

Found 0 Com Ports.

Found 3 windows drives C: D: E:

Found 2 CD/DVD drives D: E:



Loading firmware file C:\Users\Nate\Documents\Dummy.bin

MD5 hash:  af24a825c6341ab3e05a71f7516b3f8c

Inquiry string found

Identify string found

Drive key @ 0xA030 5BE19EBE0995E2340B1F7A9B2B2DE155

Firmware Osig: [PLDS    DG-16D2S        8385]

Firmware is:  iXtreme v1.60-12x-              



Auto-Loading firmware file C:\Users\Nate\Documents\JungleFlasher v0.1.70 Beta (86)\firmware\ix-lt-838.bin

MD5 hash:  187ee5780d863922d49ec1d2ed0d9f48

Genuine iXtreme Lite-Touch

Drive key @ n/a 77777777777777777777777777777777

Firmware Osig: [PLDS    DG-16D2S        8385]

Firmware is:  iXtreme LT                      



Spoofing Target

DVD Key copied to target

Inquiry string copied to Target

Identify string copied to Target

Serial data copied from Source to Target

No Calibration data in source



Spoofing Target

DVD Key already matches

ID strings already match

Serial data already matches

No Calibration data in source





Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0xD0

....................

Device Intro failed!



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0xD0

....................

Device Intro failed!



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0x72

Manufacturer ID: 0x0

Device ID: 0x0

Flash Name:  Unknown type

Flash Size:  n/a



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0x72

Manufacturer ID: 0x0

Device ID: 0x0

Flash Name:  Unknown type

Flash Size:  n/a

Unknown flash type Write aborted !



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0x80

....................

Device Intro failed!



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0x80

....................

Device Intro failed!



Sending Lite-On-Erase request to port 0x7880

..............

Drive returned Status 0x80

....................

Device Intro failed!



No Drive Detected! DVDkey files extraction aborted!