Topic: Benq 0800 and XBC 2.8 Build 275 (Read 306 times)

Toddler · « **Reply #30 on:** January 31, 2008, 11:21:00 PM »

Iriez, don't take it personally. Nothing I wrote was meant to contradict what you said, both of our posts were accurate. The fact that I quoted you may have looked like my post was a rebuttal, but the link I gave actually supported your comments. I just wanted to get the info out there, since there is so much misinformation surrounding "bad Kreon" still making the rounds.

PaddyPat · « **Reply #31 on:** February 01, 2008, 10:12:00 AM »

This firmware has worked well for me and it's been great so far. All of my backups come out perfect.
I have a few questions about XBC. When I make an Xbox original backup it creates a layer break file with the layer break set at 1913777, I think. It's the same layer break every time for Xbox original backups. Should it be different than an Xbox 360 game, which is always 1913760? I'm not at home right now, so I don't know the exact value of the Xbox original layer break, but I know it's different than Xbox 360 layer breaks.

Another comment I have is about ASPI vs. SPTI. Using the Benq drive I get an error when I use ASPI but it works perfect under SPTI. I don't know if this is because of my system or the drive or what. Just thought I'd mention it.

Thank you in advance.

shaggyarotten · « **Reply #32 on:** February 01, 2008, 04:24:00 PM »

I can rip on aspi or spti, but cannot do complete rip, have to do partion, then ss,pfi,dfi seperatly. rebuilt with mulleter. after i burn the game boots then locks up and gives dirty disc error. iso in mulleter says ss is fine but has a invlid checksum. using via card on vista.

cofree · « **Reply #33 on:** February 01, 2008, 08:43:00 PM »

well my 2 cents

I think its a great build and im glad they did it.
I flashed a benq with the 0800 and did a backup.all this was done through a blaster v1
to cool.

Keep up the good work guys

This post has been edited by cofree: Feb 2 2008, 04:45 AM

deilzfcjk · « **Reply #34 on:** February 02, 2008, 01:55:00 AM »

how long does it take you guys to make these builds? Btw, will this version make the copies true stealth. I know the lastest one(v2.7 build 0265) didn't do it correctly for ixtreme 1.4. I had to patch it using the latest Mulleter.

Or is that always going to be the case. You just have to use Mulleter to patch the iso. I mean it's not hard to do, but that would be nice if the stealth was automatic. Like I said above, I used the latest XBC as of Dec 30, 2007 and it don't make stealth copies. I know I knw I could just try it. So if anyone know if it makes stealth right off the bat post your results.

fitsman · « **Reply #35 on:** February 02, 2008, 05:56:00 AM »

QUOTE(deilzfcjk @ Feb 2 2008, 04:31 AM)

how long does it take you guys to make these builds? Btw, will this version make the copies true stealth. I know the lastest one(v2.7 build 0265) didn't do it correctly for ixtreme 1.4. I had to patch it using the latest Mulleter.

Or is that always going to be the case. You just have to use Mulleter to patch the iso. I mean it's not hard to do, but that would be nice if the stealth was automatic. Like I said above, I used the latest XBC as of Dec 30, 2007 and it don't make stealth copies. I know I knw I could just try it. So if anyone know if it makes stealth right off the bat post your results.

Here you may very wrong. The xbox backup creator(All the versions even the latest 2.

it make fully stealthed images of original xbox1 & xbox360 games. I try it to many games. I quess you may do something wrong and your images isn't stealthed for ixtreme 1.4 because me to the ixtreme 1.4 firmware i have and the games i ripred with xbox backup creator works perfectly.

PaddyPat · « **Reply #36 on:** February 02, 2008, 08:28:00 AM »

All of my backups are fully stealthed. I just make them in XBC, check in Mulleter, then straight to ImgBurn. Every one has been properly stealthed and patched so far.

NeonPinHead · « **Reply #37 on:** February 04, 2008, 06:55:00 PM »

QUOTE(Arijohn @ Jan 30 2008, 05:10 AM)

I want to keep My BEnq connected to my cpu.
How or where do i get a power converter for the Drive?

http://www.divineo.com/cgi-bin/div-us/dd-360-xck

NeonPinHead · « **Reply #38 on:** February 04, 2008, 07:19:00 PM »

early in the thread i posted all my problems and my solution. I'm using the VT6421 controller card and i had to downgrade to the 5.20a version drives and now i get the read options right off the bat without having to unlock the drive first. I have to read it in spti mode or it doesn't work.

Download the V-Raid 5.20a Driver Here.

This post has been edited by NeonPinHead: Feb 5 2008, 03:23 AM

fitsman · « **Reply #39 on:** February 05, 2008, 06:17:00 AM »

Is there a full guide that explains what every option - parameter of xbox backup creator 2.80 do?
If there is where i can find it?

A lot of thaks.

XtremeModz · « **Reply #40 on:** February 05, 2008, 10:03:00 AM »

Hey PaddyPat, do you mind telling us what settings you used to get this working okay?

shaggyarotten · « **Reply #41 on:** February 05, 2008, 10:45:00 AM »

I finally got mine working..had to switch to xp, and use the 5.20a drivers..also had to uninstall my primary and secondary ide ports frrom the device manager, and reboot, otherwise the drive would read at 0.3x speed. it was transfering to the hdd in pfi mode not dma. works flawless now. oh.. also for some reason in the settings i had to chhose dvd-rom instead of the benq, in the drive specific drop down tile.

NeonPinHead · « **Reply #42 on:** February 05, 2008, 02:17:00 PM »

QUOTE(XtremeModz @ Feb 5 2008, 09:39 AM)

Hey PaddyPat, do you mind telling us what settings you used to get this working okay?

like me he probably didn't even touch the settings. if all your drivers and everything else is setup properly this is the run down of operating this program to create a successful backup...

insert game into 360 drive
open program
select 360 drive from drop down
hit "read" ("complete backup" should all ready be selected)
make sure it's stealth using "stealth check" in "image tools"
write the image to a dvd+r dual layer using a dual layer dvd writer

it's pretty straight forward if the above doesn't go as planned the problem is not the program.

PaddyPat · « **Reply #43 on:** February 05, 2008, 05:35:00 PM »

Ya, I didn't really change many of the settings because I don't know what most of them do. In the options menu make sure you choose the right drive (VAD6038 for Benq) and the type of game you're backing up, Xbox one or Xbox 360. In the read section make sure the right drive is selected. It doesn't seem to remember your last setting, so you have to change it back every time. Complete Backup was selected....Sector Mapping for Xbox one was selected. I always used SPTI, not ASPI for some reason I don't understand. Other than that I didn't change anything.
As for the SATA card I didn't install any drivers for it at all. It just detected itself and always worked so I didn't bother with the drivers.
That's all I can think of telling you at the moment.
Good luck.

brucieboy · « **Reply #44 on:** February 12, 2008, 03:25:00 PM »

QUOTE(NeonPinHead @ Feb 5 2008, 02:55 AM)

early in the thread i posted all my problems and my solution. I'm using the VT6421 controller card and i had to downgrade to the 5.20a version drives and now i get the read options right off the bat without having to unlock the drive first. I have to read it in spti mode or it doesn't work.

Download the V-Raid 5.20a Driver Here.

I had the same problem (could not select complete backup - but I could read the disc and create an inage from it using the current partition option) and so downrevved to 5.20A.
Now, although the complete backup is selected. the option to change this is greyed out as is the start button.
i have slected the correct type of drive and also xbox 360 media in options.
I have selected SPTI and ASPI but they stil remain greyed

ANy ideas from here???

TIA

brucieboy

Author Topic: Benq 0800 and XBC 2.8 Build 275 (Read 306 times)