Topic: Can't Load Any Games With New Firmware Benq Dvd-drive (Read 21 times)

babe69 · « **on:** November 15, 2007, 08:46:00 PM »

here my prob.

using the soft flashing method

i have use the dosflash 1.3 to dump my orig.bin
use make iextrem firmware from BenQ iXtremev1.1MultiSpeed (non stealth) to have my xtreme.bin
go back to dosflash (manual method) erase command
writing command with xtreme.bin

done

checking my xbox360 with a original dvd and also backup dvd and i got put this game in a xbox360 console.

so i assume my xtreme.bin was not good

again

use Maximus 360 FW Toolbox v4.5 copy key from orig.bin ,open xtreme firmware paste key
close and open to check my key of xtreme.bin and it is the same.
go back to dosflash (manual method) erase command
writing command with xtreme.bin

go back to console

lower right red light appeared!!!!!!!! (IMG:style_emoticons/default/uhh.gif)

what happen??

im using vt6421r sata card
benq vad 6038

many thx

Ranger72 · « **Reply #1 on:** February 02, 2020, 09:06:00 PM »

Flash your original bin file to your drive and see if originals load.

Sounds like you may have gotten a bad firmware dump.

babe69 · « **Reply #2 on:** February 02, 2020, 09:15:00 PM »

im trying it ranger

give me a min

babe69 · « **Reply #3 on:** February 02, 2020, 09:30:00 PM »

QUOTE(Ranger72 @ Nov 15 2007, 11:06 PM)

Flash your original bin file to your drive and see if originals load.

Sounds like you may have gotten a bad firmware dump.

with my orig.bin back in the console it work

the diff is the rom version

orig.bin 62430c

xtrem.bin 64930c

just a bad luck or corrupt xtrem.bin??

thanks for your help

babe69 · « **Reply #4 on:** February 02, 2020, 10:07:00 PM »

i retry to replace the key with maximus toolbox 4.5
non-stealth firmware

erase command
write command

still lower right red light

with orig.bin all is ok

someone that have used non-stealth firmware from iXtreme_Firmware_BenQ_v1.1.MultiSpeed-XBOX360-iND

that has successfully flash a benq drive??

cypher21 · « **Reply #5 on:** February 03, 2020, 02:11:00 AM »

QUOTE(babe69 @ Nov 16 2007, 05:07 AM)

i retry to replace the key with maximus toolbox 4.5
non-stealth firmware

erase command
write command

still lower right red light

with orig.bin all is ok

someone that have used non-stealth firmware from iXtreme_Firmware_BenQ_v1.1.MultiSpeed-XBOX360-iND

that has successfully flash a benq drive??

toolbox has some issues with benq firmware

USE FIRMTOOL!!!!!

babe69 · « **Reply #6 on:** February 03, 2020, 06:30:00 AM »

QUOTE(cypher21 @ Nov 16 2007, 04:11 AM)

toolbox has some issues with benq firmware

USE FIRMTOOL!!!!!

thanks cypher21 for your help

as i state in my first post

i have use firmtool first ( dump orig.bin in firmware folder and run Make iXtreme firmware.cmd )

and i got " put this disk in a xbox ........ message" for original or backup

any ideas??

caster420 · « **Reply #7 on:** February 03, 2020, 06:47:00 AM »

QUOTE(babe69 @ Nov 16 2007, 08:30 AM)

i have use firmtool first ( dump orig.bin in firmware folder and run Make iXtreme firmware.cmd )
and i got " put this disk in a xbox ........ message" for original or backup
any ideas??

Did firmtool run and complete successfully? Firmtool automatically copies your version strings over, so your xtreme.bin should say it is a 62430, not 64930. It sounds to me like it didnt run or errored out, or it would have changed those strings at a minimum, even if it did for some reason find the wrong key.

Caster.

cypher21 · « **Reply #8 on:** February 03, 2020, 07:26:00 AM »

what also might be an issue, is that you use the older version of firmtool. Caster updated it to 1.1 because there were some firmwares that were dumped correctly but the hacked version wasn't created correctly.

To be sure, create a new hacked firmware with 1.1

you can find the link in this threat: http://forums.xbox-scene.com/index.php?showtopic=629470

caster420 · « **Reply #9 on:** February 03, 2020, 07:29:00 AM »

QUOTE(cypher21 @ Nov 16 2007, 09:26 AM)

what also might be an issue, is that you use the older version of firmtool. Caster updated it to 1.1 because there were some firmwares that were dumped correctly but the hacked version wasn't created correctly.

That issue was only associated with spoofing BenQ firmware to report as a Hitachi or a Samsung, or spoofing Samsung firmware to report as a BenQ. Copying version strings of the same firmware type is not effected, or we would have had the issue from the beginning (a lot of people have v62430's when the hacked fw is v64930).

Still wouldnt hurt to update but i dont think thats the issue.

Caster.

cypher21 · « **Reply #10 on:** February 03, 2020, 07:52:00 AM »

QUOTE(caster420 @ Nov 16 2007, 02:29 PM)

That issue was only associated with spoofing BenQ firmware to report as a Hitachi or a Samsung, or spoofing Samsung firmware to report as a BenQ. Copying version strings of the same firmware type is not effected, or we would have had the issue from the beginning (a lot of people have v62430's when the hacked fw is v64930).
Still wouldnt hurt to update but i dont think thats the issue.
Caster.

Ah, in that case i didn;t read right, i thought there was one case which had a firmware you didn't see before and couldn't create the hacked version.

edit: found it, it was alinush' version of the benq

This post has been edited by cypher21: Yesterday, 03:54 PM

caster420 · « **Reply #11 on:** February 03, 2020, 08:02:00 AM »

QUOTE(cypher21 @ Nov 16 2007, 09:52 AM)

edit: found it, it was alinush' version of the benq

Yes, his firmware was messed up and is still the only one like that i have seen to date.

Caster.

babe69 · « **Reply #12 on:** February 03, 2020, 03:11:00 PM »

PROBLEM SOLVED!!

many many thanks to cypher21 and caster420 for there great help!

what it supposed to take 15 min. takes me abt 2 hours last night and all that for a software bug (IMG:style_emoticons/default/laugh.gif) (IMG:style_emoticons/default/laugh.gif)

great job guys

respect

Author Topic: Can't Load Any Games With New Firmware Benq Dvd-drive (Read 21 times)