Print

[LEXS]

Whats up guys i have a A8N32sli mb an im trying to edit mtkflash an as you can see i only have one i/o port  which dont look rite so im short of 4 bytes. Tia.......

Name   Silicon Image SiI 3132 SATALink Controller
Manufacturer   Silicon Image
Status   OK
PNP Device ID   PCI\VEN_1095&DEV_3132&SUBSYS_819F1043&REV_01\4&E2974D5&0&0010
Memory Address   0xDFCFFC00-0xDFCFFC7F
Memory Address   0xDFCF8000-0xDFCFBFFF
I/O Port   0x0000BC00-0x0000BC7F
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\si3132.sys (1, 0, 7, 0, 100.00 KB (102,400 bytes), 12/12/2005 10:12 AM)

[chipD]

QUOTE(LEXS @ Jun 5 2006, 07:05 AM)

Whats up guys i have a A8N32sli mb an im trying to edit mtkflash an as you can see i only have one i/o port  which dont look rite so im short of 4 bytes. Tia.......

Name   Silicon Image SiI 3132 SATALink Controller
Manufacturer   Silicon Image
Status   OK
PNP Device ID   PCI\VEN_1095&DEV_3132&SUBSYS_819F1043&REV_01\4&E2974D5&0&0010
Memory Address   0xDFCFFC00-0xDFCFFC7F
Memory Address   0xDFCF8000-0xDFCFBFFF
I/O Port   0x0000BC00-0x0000BC7F
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\si3132.sys (1, 0, 7, 0, 100.00 KB (102,400 bytes), 12/12/2005 10:12 AM)

Are you using the NF4 mtkflash?

[LEXS]

QUOTE(chipD @ Jun 5 2006, 07:29 AM)

Are you using the NF4 mtkflash?

Yes i tried MTK-NF4 an this is what i get, Port: a480, Master/Slave: a0, i also make sure that its set to sata in the bios.

[LEXS]

K, I found this under IDE in System Information,

Name   NVIDIA nForce4 Serial ATA Controller
Manufacturer   NVIDIA Corporation
Status   OK
PNP Device ID   PCI\VEN_10DE&DEV_0054&SUBSYS_815A1043&REV_F3\3&267A616A&0&80
I/O Port   0x0000A480-0x0000A487
I/O Port   0x0000A400-0x0000A403
I/O Port   0x0000A080-0x0000A087
I/O Port   0x0000A000-0x0000A003
I/O Port   0x00009C00-0x00009C0F
Memory Address   0xDFBFD000-0xDFBFDFFF
IRQ Channel   IRQ 23
Driver   c:\windows\system32\drivers\nvata64.sys (5.10.2600.0552 built by: WinDDK, 146.50 KB (150,016 bytes), 2/12/2006 12:01 PM)
   
Name   NVIDIA nForce4 Serial ATA Controller
Manufacturer   NVIDIA Corporation
Status   OK
PNP Device ID   PCI\VEN_10DE&DEV_0055&SUBSYS_815A1043&REV_F3\3&267A616A&0&88
I/O Port   0x00009880-0x00009887
I/O Port   0x00009800-0x00009803
I/O Port   0x00009480-0x00009487
I/O Port   0x00009400-0x00009403
I/O Port   0x00009080-0x0000908F
Memory Address   0xDFBFC000-0xDFBFCFFF
IRQ Channel   IRQ 20
Driver   c:\windows\system32\drivers\nvata64.sys (5.10.2600.0552 built by: WinDDK, 146.50 KB (150,016 bytes), 2/12/2006 12:01 PM)

So i edit MTKFLASH with these values DE10 5400 804A 80A0 which looks like this
(IMG:http://img477.imageshack.us/img477/7796/hex8ql.png)
 an still the same problem what am i doing wrong?

[Havok]

You are not hex editing the right values.

Try:

DE10 5400 80A4 80A0

You had the A and 4 reversed.

[LEXS]

QUOTE(Havok @ Jun 5 2006, 04:31 PM)

You are not hex editing the right values.

Try:

DE10 5400 80A4 80A0

You had the A and 4 reversed.

 Yea no go still stuck at Port: a480, Master/Slave?a0.

[PurpleHippo]

My friend had same problem, perhaps THIS will help.

[Havok]

QUOTE(LEXS @ Jun 5 2006, 05:01 PM)

Yea no go still stuck at Port: a480, Master/Slave?a0.

then you did not save your changes. The port should have changed to 80a4.

you know flashing with a Si3112 does not work right?

You will need a different PCI card to flash.

[LEXS]

QUOTE(Havok @ Jun 5 2006, 06:44 PM)

then you did not save your changes. The port should have changed to 80a4.

you know flashing with a Si3112 does not work right?

You will need a different PCI card to flash.

Actually i already backup an flashed this drive once its that i used KDX-1.1 for the drive key an now it wont boot anything so i redid the flash with hex edit an trying to reflash it, i had used mtk-nf4 but the one i got was already patched an i formated the original floppy it was on cause i needed it, also have another drive form another 360 which i cant backup cause im having the same problem reading from the drive, also i rechecked my edit mtkflash an the values are changed.