Print

[Grim187]

QUOTE(hecz @ Apr 24 2007, 02:51 PM)

hi I want to know if my sata is compatible ive flashed a lot of hitachis never a samsung Im trying to flash a ms25 and can I power up the drive with the x360 usb to sata? (xecuter)
Name   Intel® 82801EB Ultra ATA Storage Controllers
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_24DB&SUBSYS_24D01849&REV_02\3&267A616A&0&F9
I/O Port   0x0000FC00-0x0000FC0F
Memory Address   0xFF37FC00-0xFF37FFFF
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 3:00 AM)
   
Name   D347PRT SCSI Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   PCI\D347PRT\0000
Driver   c:\windows\system32\drivers\d347prt.sys (3.47.0.0 built by: WinDDK, 5.13 KB (5,248 bytes), 2/1/2007 2:33 PM)
   
Name   XMASSCSI SCSI Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   PCI\XMASSCSI\0000
Driver   c:\windows\system32\drivers\xmasscsi.sys (3.44.0.0 built by: WinDDK, 5.38 KB (5,504 bytes), 4/12/2007 3:26 PM)

its sata to usb and that only works for hitachis since theres no usb drivers in dos

you havent showen me a sata controller, try installing your driver

[hecz]

QUOTE(Grim187 @ Apr 24 2007, 11:56 PM)

its sata to usb and that only works for hitachis since theres no usb drivers in dos

you havent showen me a sata controller, try installing your driver

ive checked on my MOBO book and the only thing it says : asrock 775i65g,  Intel ICH5 (near the sata)

went to the page for the drivers and there is no drivers :S.

any ideas?

and i connect the hitachi drive straight to the sata and its recognized :S

and about the samsung and the x360 usb , I asked about using the power not the adaptor (sata to usb) cuz i dont like the idea of powering my 360 and the pc at the same time

[Sniper_Monkey]

Hi Grim, I am hoping you can help me or someone else can.

I am using an xbox 360 with a MS25 drive. I am making a usb bootable drive with the latest version of xtreme boot maker. I am using a VIA VT6421 SATA card.

If i look under MSINFO32 etc, in the IDE i have a Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0 - and if I look under SCSI I have VIA VT6421 RAID Controller.

Now in extreme boot maker I selet the correct firmware and the it says make custom MKTFLASH so i select it and it detects my VIA Sata card and gives them a device ID of 11063249 and a I/O Port of DC00D800. So i go ahead and format and make bootable.

I boot into dos with the sata cable from card NOT in the back of the dvd drive ofthe 360. It comes to the prompt so I type samread ******* ***** and it offers me one selection of 1. IDE Primary Master. The only think it seems to be able to detect is my IDE CDROM.

I have read some tutorials and am stuck.

I understand that the latest version of Extreme Boot Maker does all the hex editing for you, correct?

Thanks in advance to Grim or anyone that can help.

[Sniper_Monkey]

Problem solved, thanks guys

[ynnad]

Hey all,

i need some help editing mtkflash to suit my SATA chipset.

the Info:
Name   NVIDIA nForce4 Serial ATA Controller
Manufacturer   NVIDIA Corporation
Status   OK
PNP Device ID   PCI\VEN_10DE&DEV_0054&SUBSYS_B0031458&REV_F3\3&2411E6FE&0&38
I/O Port   0x000009F0-0x000009F7
I/O Port   0x00000BF0-0x00000BF3
I/O Port   0x00000970-0x00000977
I/O Port   0x00000B70-0x00000B73
I/O Port   0x0000D000-0x0000D00F

What i thought: DE10 5400
and                  F009 7009

P.S. i just wanted to confirm when editing the mtkyflash file all i do is Goto B370 and start typing in the new hex codes. (it does contain nvidia stuff in the text on the right so im pretty sure im in the right spot)

Also i havent seen anyone elses code with a letter in it?

I would appreciate any help!

Cheers

[Blanck]

Hello, I would hereby like to get a confirmation from someone that what I think is correct actually is~

Name   ATI AHCI Compatible RAID Controller
Manufacturer   ATI Technologies Inc.
Status   OK
PNP Device ID   PCI\VEN_1002&DEV_4380&SUBSYS_72431462&REV_00\3&267A616A&0&90
I/O Port   0x0000E800-0x0000E807
I/O Port   0x0000E400-0x0000E403
I/O Port   0x0000E000-0x0000E007
I/O Port   0x0000DC00-0x0000DC03
I/O Port   0x0000D800-0x0000D80F
Memory Address   0xFFEFFC00-0xFFEFFFFF
IRQ Channel   IRQ 22
Driver   c:\windows\system32\drivers\ahcix64s.sys (2.5.1540.35, 135.40 KB (138,648 bytes), 1/3/2007 4:18 PM)



1. So was I correct in that the following is the sequence I have to hex-"inject"?
02108043 00E800E0

2. And in this example, have I injected it in the correct place?
[img=http://img524.imageshack.us/img524/6849/mktflashdk8.th.jpg]

3. Would it be ok for me to change the text
VIA8237 (which is actually 56 4941 3832 3337?)
or rather, would this be needed at all? Or can this text be ignored completely?


Please point out anything I've done wrong so far in editing MTKflash to flash my drive, or confirm if what I've come up with so far is correct~ Are there any other problems I might encounter while retrieving the original flash and flashing the hacked one with this setup or type of SATA controller?

Thank you~

This post has been edited by Blanck: May 15 2007, 11:04 PM

[PhatheadWRX]

trying to get my Gigabyte GA-965P-S3 working with Sammy ms25.

under Storage/IDE:

Name   Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_27C0&SUBSYS_B0021458&REV_01\3&13C0B0C5&0&FA
I/O Port   0x0000F000-0x0000F00F
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 8:00 AM)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&1C8F7963&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 5:59 PM)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&1C8F7963&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 5:59 PM)

I know 8680 C027, but not the IO part.

Thanks Grim / whoever!

This post has been edited by PhatheadWRX: May 22 2007, 09:27 PM

[Lifedrain]

Is it possible to do this with an asus m2n32 ws pro mainboard? [nforce and marvell SATA-Controllers]

Flashing Samsung Ms28. Hope for an quick answer! =)

This post has been edited by Lifedrain: May 23 2007, 04:51 PM

[BEVEL]

Is there some kind of list of motherboards or chipsets that work with flashing?

I got a Asus commando, with JMicron JMB36X Controller.

I cant get my Samsung ms25 flashed, it wont get recognised
I tried xtreme boot maker, no help
anyone tried this yet ?

This post has been edited by BEVEL: May 23 2007, 09:56 PM

[BEVEL]

bump, srry
getting frustrated, 2 day at it

[BEVEL]

Just another quick question
Is your drive supposed to be found when you check your bios?

[Grim187]

QUOTE(hecz @ Apr 25 2007, 12:45 AM)

ive checked on my MOBO book and the only thing it says : asrock 775i65g,  Intel ICH5 (near the sata)

went to the page for the drivers and there is no drivers :S.

any ideas?

and i connect the hitachi drive straight to the sata and its recognized :S

and about the samsung and the x360 usb , I asked about using the power not the adaptor (sata to usb) cuz i dont like the idea of powering my 360 and the pc at the same time

http://www.google.com/search?sourceid=navc...;q=ich5+drivers
ya you can use the xkit or x360 to power the drive

QUOTE(Sniper_Monkey @ Apr 26 2007, 09:14 PM)

Hi Grim, I am hoping you can help me or someone else can.

I am using an xbox 360 with a MS25 drive. I am making a usb bootable drive with the latest version of xtreme boot maker. I am using a VIA VT6421 SATA card.

If i look under MSINFO32 etc, in the IDE i have a Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0 - and if I look under SCSI I have VIA VT6421 RAID Controller.

Now in extreme boot maker I selet the correct firmware and the it says make custom MKTFLASH so i select it and it detects my VIA Sata card and gives them a device ID of 11063249 and a I/O Port of DC00D800. So i go ahead and format and make bootable.

I boot into dos with the sata cable from card NOT in the back of the dvd drive ofthe 360. It comes to the prompt so I type samread ******* ***** and it offers me one selection of 1. IDE Primary Master. The only think it seems to be able to detect is my IDE CDROM.

I have read some tutorials and am stuck.

I understand that the latest version of Extreme Boot Maker does all the hex editing for you, correct?

Thanks in advance to Grim or anyone that can help.

ich7 works but its alittle buggy so its good you got the via, make sure you are using the port closest to the front of the computer on the via card

i wouldent use sam, just use mtkflash r /m /sata orig.bin

QUOTE(Blanck @ May 15 2007, 03:39 PM)

Hello, I would hereby like to get a confirmation from someone that what I think is correct actually is~

Name   ATI AHCI Compatible RAID Controller
Manufacturer   ATI Technologies Inc.
Status   OK
PNP Device ID   PCI\VEN_1002&DEV_4380&SUBSYS_72431462&REV_00\3&267A616A&0&90
I/O Port   0x0000E800-0x0000E807
I/O Port   0x0000E400-0x0000E403
I/O Port   0x0000E000-0x0000E007
I/O Port   0x0000DC00-0x0000DC03
I/O Port   0x0000D800-0x0000D80F
Memory Address   0xFFEFFC00-0xFFEFFFFF
IRQ Channel   IRQ 22
Driver   c:\windows\system32\drivers\ahcix64s.sys (2.5.1540.35, 135.40 KB (138,648 bytes), 1/3/2007 4:18 PM)
1. So was I correct in that the following is the sequence I have to hex-"inject"?
02108043 00E800E0

2. And in this example, have I injected it in the correct place?
[img=http://img524.imageshack.us/img524/6849/mktflashdk8.th.jpg]

3. Would it be ok for me to change the text
VIA8237 (which is actually 56 4941 3832 3337?)
or rather, would this be needed at all? Or can this text be ignored completely?
Please point out anything I've done wrong so far in editing MTKflash to flash my drive, or confirm if what I've come up with so far is correct~ Are there any other problems I might encounter while retrieving the original flash and flashing the hacked one with this setup or type of SATA controller?

Thank you~

looks good, i dont see anyreason to change it but you can to a max of 10 digits (i think)

[Console Man]

Hi all,

I have been following 'The Specialists' guide for using hddhackr and i have been directed to this thread n the forum. I have a version of mtkflash which i have hex edited and works perfect and i have tried hex editing hddhackr with the same bytes, is this the correct proceedure?

Here is my details:

Name   VIA VT6421 RAID Controller
Manufacturer   VIA Technologies, Inc.
Status   OK
PNP Device ID   PCI\VEN_1106&DEV_3249&SUBSYS_32491106&REV_50\3&61AAA01&0&38
I/O Port   0x0000D800-0x0000D80F
I/O Port   0x0000D400-0x0000D40F
I/O Port   0x0000D000-0x0000D00F
I/O Port   0x0000CC00-0x0000CC0F
I/O Port   0x0000C800-0x0000C81F
I/O Port   0x0000C400-0x0000C4FF
IRQ Channel   IRQ 18
Driver   c:\windows\system32\drivers\viamraid.sys (5.1.2600.542, 101.63 KB (104,064 bytes), 30/04/2007 13:20)
   
Name   SCSI/RAID Host Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   ACPI\PNPA000\4&5D18F2DF&0
I/O Port   0x0000FFE0-0x0000FFEF
IRQ Channel   IRQ 9


I use 0611 4932 D024 B024 which i know is SLIGHTYLY different from what my settings say but it works perfectly with MTKFLASH but not HDDHACKR. Can anyone give me any advice on how i should edit HDDHACKR so my 120GB original drive gets regonised so i can copy onto a new WD 120BEV. I have tried a few different settings but after a day of hex editing my head is buzzing and i feel i am over looking something simple.

Any help is greatly appreciated

This post has been edited by Console Man: Jun 22 2007, 09:56 PM

[Grim187]

QUOTE(Console Man @ Jun 22 2007, 02:28 PM)

Hi all,

I have been following 'The Specialists' guide for using hddhackr and i have been directed to this thread n the forum. I have a version of mtkflash which i have hex edited and works perfect and i have tried hex editing hddhackr with the same bytes, is this the correct proceedure?

Here is my details:

Name   VIA VT6421 RAID Controller
Manufacturer   VIA Technologies, Inc.
Status   OK
PNP Device ID   PCI\VEN_1106&DEV_3249&SUBSYS_32491106&REV_50\3&61AAA01&0&38
I/O Port   0x0000D800-0x0000D80F
I/O Port   0x0000D400-0x0000D40F
I/O Port   0x0000D000-0x0000D00F
I/O Port   0x0000CC00-0x0000CC0F
I/O Port   0x0000C800-0x0000C81F
I/O Port   0x0000C400-0x0000C4FF
IRQ Channel   IRQ 18
Driver   c:\windows\system32\drivers\viamraid.sys (5.1.2600.542, 101.63 KB (104,064 bytes), 30/04/2007 13:20)
   
Name   SCSI/RAID Host Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   ACPI\PNPA000\4&5D18F2DF&0
I/O Port   0x0000FFE0-0x0000FFEF
IRQ Channel   IRQ 9
I use 0611 4932 D024 B024 which i know is SLIGHTYLY different from what my settings say but it works perfectly with MTKFLASH but not HDDHACKR. Can anyone give me any advice on how i should edit HDDHACKR so my 120GB original drive gets regonised so i can copy onto a new WD 120BEV. I have tried a few different settings but after a day of hex editing my head is buzzing and i feel i am over looking something simple.

Any help is greatly appreciated

0611 4932 00D8 00D0

[Console Man]

QUOTE(Grim187 @ Jun 23 2007, 01:02 AM)

0611 4932 00D8 00D0

Thanks m8, i just had DOH moment, i had tried that figure in Hex last night and it didnt work, then i reaslise that i was saving file to pc and not USB pen and was try same unedited file over and over again LOL

DOH
DOH
DOH

All is well and fine now, thanks m8  (IMG:style_emoticons/default/biggrin.gif)