Print

[Grim187]

QUOTE(icechilly @ May 26 2006, 06:17 PM)

woah, no need to be busting out the red font.

just installed my drivers, lol cant believe i missed that
anyway i got it all working now thanks for the help!

well it is in the tut, for future ref read over the tut more then once and then refer to it as you go along the steps

Statement to everyone: Try to Refrain from asking questions that have been already answered

[lamer01]

QUOTE(Grim187 @ May 26 2006, 03:58 AM)

try

CODE

0210 7643 2B33 0B6B

if that dosent work then you will probly need a pci card

Grim, thanx. I got a little further this time.
I used the numbers from the 1st and 2nd controller entry and I replaced ICHP5 with
02107A4300FF00FD
and ICHP6 with
0210794300FA00F8.

I turned off the regular IDE in the bios and now mktflash says it found something.
Depending on where I have the drive plugged in I get the following:
1. ICHP5: Master
2. ICHP5: Slave

or

1. ICHP6: Master
2. ICHP6: Slave

No matter what I pick though, I get somekind of a port: ### and another number and then the pc is frozen.

The port:### looks like the ports in the numbers above like 00FF or 00FD or 00FA 00F8 and the code is a0 or b0.
I think I am getting closer.



lamer01

[Grim187]

QUOTE(lamer01 @ May 26 2006, 07:04 PM)

Grim, thanx. I got a little further this time.
I used the numbers from the 1st and 2nd controller entry and I replaced ICHP5 with
02107A4300FF00FD
and ICHP6 with
0210794300FA00F8.

I turned off the regular IDE in the bios and now mktflash says it found something.
Depending on where I have the drive plugged in I get the following:
1. ICHP5: Master
2. ICHP5: Slave

or

1. ICHP6: Master
2. ICHP6: Slave

No matter what I pick though, I get somekind of a port: ### and another number and then the pc is frozen.

The port:### looks like the ports in the numbers above like 00FF or 00FD or 00FA 00F8 and the code is a0 or b0.
I think I am getting closer.
lamer01

the problem is your ide channels are a little bit to buddy buddy with your SATA channels, try disabling all ide channels in your cosmos and using this

CODE

0210 7643 F001 7001

[lamer01]

QUOTE(Grim187 @ May 27 2006, 03:14 AM)

the problem is your ide channels are a little bit to buddy buddy with your SATA channels, try disabling all ide channels in your cosmos and using this

CODE

0210 7643 F001 7001

Thanks Grim. I have that in there as well. I used the nforce 3 entry for that one. Basically I entered all the controllers (3 of them) that show up in msinfo into mtkflash. Am I confusing mtkflash?


lamer01

[RWill55904]

Hello Grim.

I have an Gigabyte K8U-989 Atx Motherboard
360 Toshiba Drive FW:MS 25 Feb 2006

Here are my driver specs for my sata chipset

Name   ALi SATA/RAID Controller (M5289)
Manufacturer   ALi Corporation
Status   OK
PNP Device ID   PCI\VEN_10B9&DEV_5289&SUBSYS_B0031458&REV_10\3&13C0B0C5&0&71
I/O Port   0x0000D400-0x0000D407
I/O Port   0x0000D800-0x0000D803
I/O Port   0x0000DC00-0x0000DC07
I/O Port   0x0000E000-0x0000E003
I/O Port   0x0000E400-0x0000E40F
IRQ Channel   IRQ 19
Driver   c:\windows\system32\drivers\m5289.sys (5.029, 50.63 KB (51,840 bytes), 5/27/2006 1:22 AM)


I cant get my mktflash to recognize the drive to dump the firmware, I spent most of the night, reading the post. I have booted with all IDE channels disabled, Connected XBOX Toshiba Drive with sata no power,
boot to floppy, then power up the 360 when I get the prompt. Type in the mtkflash r backup.bin. Also tried the /sata command. None of these work. I am sure this can work if I can get some help on this hex edit ( which I am not too familiar with by the way.) I was wondering could you use my info to make a screenshot of how it would look correctly in Hexedit? Or if you can edit MKTFlash for me and email it to me if possible or post on a share site like rapidshare?

I know I`m asking alot, but I dont want to brick it,and I will use the info you give me to get this down..
I can do everything hacking the Xbox ( i post on slayers forum all the time) I was just hoping you can lend a 360 N00b a helping hand?

Thanks
RWill55904

[Grim187]

QUOTE(RWill55904 @ May 27 2006, 12:53 AM)

Hello Grim.

I have an Gigabyte K8U-989 Atx Motherboard
360 Toshiba Drive FW:MS 25 Feb 2006

Here are my driver specs for my sata chipset

I cant get my mktflash to recognize the drive to dump the firmware, I spent most of the night, reading the post. I have booted with all IDE channels disabled, Connected XBOX Toshiba Drive with sata no power,
boot to floppy, then power up the 360 when I get the prompt. Type in the mtkflash r backup.bin. Also tried the /sata command. None of these work. I am sure this can work if I can get some help on this hex edit ( which I am not too familiar with by the way.) I was wondering could you use my info to make a screenshot of how it would look correctly in Hexedit? Or if you can edit MKTFlash for me and email it to me if possible or post on a share site like rapidshare?

I know I`m asking alot, but I dont want to brick it,and I will use the info you give me to get this down..
I can do everything hacking the Xbox ( i post on slayers forum all the time) I was just hoping you can lend a 360 N00b a helping hand?

Thanks
RWill55904

Geremia over at XBH has a ALI card that he got to work its got a little bit different specs other wise i would give you the link to his, but it is known that some ALI cards work, guess you just gotta keep trying
MTKFlash for your ALI SATA Chipset
also try booting with all IDE channels enabled but only one drive hooked up (DVD drive),if you can disable Bootrom in the bios then you don't need to hot swap or Boot dos and the 360 separately (when booting separately make sure you have the 360 SATA connected to the 360)
Right now not even being able to get it detected in windows you couldn't make it a brick if you wanted to(well at least not without a hammer)

Hope this Helps

P.S. i don't use those post-it now Websites, i have my own from www.1001megs.com

Edit: Spelling

[i_am_ugf]

Tried to flash today with ich5 chipset...when it ype mtkflash r/m origin.bin i get the option for master and slave and when i press either of them i get failed to open input file.
Also in msinfo32.exe the ich5 doesnt appear on the scsi at all
pls help me out

[i_am_ugf]

Name   Intel® 82801EB Ultra ATA Storage Controllers
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_24DB&SUBSYS_24D217F2&REV_02\3&13C0B0C5&0&F9
I/O Port   0x0000F000-0x0000F00F
Memory Address   0xFEBFFC00-0xFEBFFFFF
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 3:00 PM)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&371145FE&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 10:59 PM)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&371145FE&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 10:59 PM)
   
Name   Intel® 82801EB Ultra ATA Storage Controllers
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_24D1&SUBSYS_24D117F2&REV_02\3&13C0B0C5&0&FA
I/O Port   0x0000C000-0x0000C007
I/O Port   0x0000C400-0x0000C403
I/O Port   0x0000C800-0x0000C807
I/O Port   0x0000CC00-0x0000CC03
I/O Port   0x0000D000-0x0000D00F
IRQ Channel   IRQ 18
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 3:00 PM)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&E5C5E24&0&0
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 10:59 PM)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&E5C5E24&0&1
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 8/3/2004 10:59 PM)
 

these are my ide

[mpowerluke]

I am using this board:

A8N32-SLI Deluxe

My Chipset:

Nvidia NForce4 SLIx16

MY "Storage"

NVIDIA Nforce4 "supports":
2 x ultra DMA 133/100/66/33 connectors for up to 4 IDE devices
4 x Serial ATA devices (3 Gb/s)
NVIDIA for RAID 0, RAID 1, RAID 0+1, RAID 5, and
JBOD configuration that spans across Serial ATA drives

I ALSO HAVE:

Silicon Image 3132 SATA controller "supports":
1 x Internal Serial ATA device (3 Gb/s)
1 x External Serial ATA device (3 Gb/s)
(for SATA On-The-Go)
RAID 0 and RAID 1 configurations.


~~~
I am using an Nforce4 and also a regular mtkflash.exe file.

My best reslut so far....

I can disable everything but the floppy and xbox drive in the bios

I am able to recognize the drive with mtkflash

I select master sata

Then the cursor will either hang or it will give some port info...

Has ANYON actually gotten the board/chipset to work?




Here is my "system information"
**listed under IDE, NOT scsi**


Name   NVIDIA nForce4 Serial ATA Controller
Manufacturer   NVIDIA Corporation
Status   OK
PNP Device ID   PCI\VEN_10DE&DEV_0054&SUBSYS_815A1043&REV_F3\3&267A616A&0&80
I/O Port   0x0000DC00-0x0000DC07
I/O Port   0x0000D880-0x0000D883
I/O Port   0x0000D800-0x0000D807
I/O Port   0x0000D480-0x0000D483
I/O Port   0x0000D400-0x0000D40F
Memory Address   0xFEBFC000-0xFEBFCFFF
IRQ Channel   IRQ 22
Driver   c:\windows\system32\drivers\nvata.sys (5.10.2600.0552 built by: WinDDK, 91.38 KB (93,568 bytes), 4/24/2006 8:17 PM)

Name   NVIDIA nForce4 Serial ATA Controller
Manufacturer   NVIDIA Corporation
Status   OK
PNP Device ID   PCI\VEN_10DE&DEV_0055&SUBSYS_815A1043&REV_F3\3&267A616A&0&88
I/O Port   0x0000D080-0x0000D087
I/O Port   0x0000D000-0x0000D003
I/O Port   0x0000CC00-0x0000CC07
I/O Port   0x0000C880-0x0000C883
I/O Port   0x0000C800-0x0000C80F
Memory Address   0xFEBFB000-0xFEBFBFFF
IRQ Channel   IRQ 23
Driver   c:\windows\system32\drivers\nvata.sys (5.10.2600.0552 built by: WinDDK, 91.38 KB (93,568 bytes), 4/24/2006 8:17 PM)

***THIS IS WHAT I HAVE UNDER SCSI***

Name   Silicon Image SiI 3132 SoftRaid 5 Controller
Manufacturer   Silicon Image
Status   OK
PNP Device ID   PCI\VEN_1095&DEV_3132&SUBSYS_81771043&REV_01\4&E2974D5&0&0010
Memory Address   0xF47FFC00-0xF47FFC7F
Memory Address   0xF47F8000-0xF47FBFFF
I/O Port   0x0000AC00-0x0000AC7F
IRQ Channel   IRQ 16
Driver   c:\windows\system32\drivers\si3132r5.sys (1, 4, 3, 0, 195.00 KB (199,680 bytes), 1/12/2006 10:41 AM)




Thanks in advance!

[Grim187]

QUOTE(lamer01 @ May 26 2006, 07:54 PM)

Thanks Grim. I have that in there as well. I used the nforce 3 entry for that one. Basically I entered all the controllers (3 of them) that show up in msinfo into mtkflash. Am I confusing mtkflash?
lamer01

Could Be

QUOTE(i_am_ugf @ May 27 2006, 07:42 AM)

these are my ide

non of those are SATA controllers

QUOTE(mpowerluke @ May 27 2006, 07:52 AM)

I am using this board:

A8N32-SLI Deluxe

My Chipset:

Nvidia NForce4 SLIx16

MY "Storage"

NVIDIA Nforce4 "supports":
2 x ultra DMA 133/100/66/33 connectors for up to 4 IDE devices
4 x Serial ATA devices (3 Gb/s)
NVIDIA for RAID 0, RAID 1, RAID 0+1, RAID 5, and
JBOD configuration that spans across Serial ATA drives

I ALSO HAVE:

Silicon Image 3132 SATA controller "supports":
1 x Internal Serial ATA device (3 Gb/s)
1 x External Serial ATA device (3 Gb/s)
(for SATA On-The-Go)
RAID 0 and RAID 1 configurations.
~~~
I am using an Nforce4 and also a regular mtkflash.exe file.

My best reslut so far....

I can disable everything but the floppy and xbox drive in the bios

I am able to recognize the drive with mtkflash

I select master sata

Then the cursor will either hang or it will give some port info...

Has ANYON actually gotten the board/chipset to work?
Here is my "system information"
**listed under IDE, NOT scsi**
Name   NVIDIA nForce4 Serial ATA Controller


Name   NVIDIA nForce4 Serial ATA Controller


***THIS IS WHAT I HAVE UNDER SCSI***

Name   Silicon Image SiI 3132 SoftRaid 5 Controller

Have you even tried to Edit MTKFlash, i don't see that you have nor do i see a question relevant to Editing MTKFlash so y are you posting?

[i_am_ugf]

Name   Intel® 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_27DF&SUBSYS_81791043&REV_01\3&11583659&0&F9
I/O Port   0x0000FFA0-0x0000FFAF
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 23/8/2001 15:00)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&A663227&0&0
I/O Port   0x000001F0-0x000001F7
I/O Port   0x000003F6-0x000003F6
IRQ Channel   IRQ 14
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 3/8/2004 22:59)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&A663227&0&1
I/O Port   0x00000170-0x00000177
I/O Port   0x00000376-0x00000376
IRQ Channel   IRQ 15
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 3/8/2004 22:59)
   
Name   Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_27C0&SUBSYS_26011043&REV_01\3&11583659&0&FA
I/O Port   0x0000E400-0x0000E407
I/O Port   0x0000E080-0x0000E083
I/O Port   0x0000E000-0x0000E007
I/O Port   0x0000DC00-0x0000DC03
I/O Port   0x0000D880-0x0000D88F
Memory Address   0xFEBFB800-0xFEBFBBFF
IRQ Channel   IRQ 23
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 23/8/2001 15:00)
   
Name   Primary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&3803E7E3&0&0
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 3/8/2004 22:59)
   
Name   Secondary IDE Channel
Manufacturer   (Standard IDE ATA/ATAPI controllers)
Status   OK
PNP Device ID   PCIIDE\IDECHANNEL\4&3803E7E3&0&1
Driver   c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 3/8/2004 22:59)

THIS IS ME IDE

AND THIS SCSI

Name   Marvell RAID 614x
Manufacturer   Marvell Inc.
Status   OK
PNP Device ID   PCI\VEN_11AB&DEV_6141&SUBSYS_81D61043&REV_01\4&186DEF45&0&00E5
I/O Port   0x00009C00-0x00009C07
I/O Port   0x00009880-0x00009883
I/O Port   0x00009800-0x0000983F
I/O Port   0x00009480-0x0000949F
Memory Address   0xFA7FFC00-0xFA7FFFFF
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\mv614x.sys (, 33.63 KB (34,432 bytes), 27/5/2006 00:06)
   
Name   SCSI/RAID Host Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   ACPI\PNPA000\4&41721A99&0
I/O Port   0x0000FFE0-0x0000FFEF
IRQ Channel   IRQ 9
Driver   c:\windows\system32\drivers\dtscsi.sys (, 217.90 KB (223,128 bytes), 19/5/2006 16:34)

[Grim187]

QUOTE(i_am_ugf @ May 27 2006, 09:08 AM)

   
Name   Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_27C0&SUBSYS_26011043&REV_01\3&11583659&0&FA
I/O Port   0x0000E400-0x0000E407
I/O Port   0x0000E080-0x0000E083
I/O Port   0x0000E000-0x0000E007
I/O Port   0x0000DC00-0x0000DC03
I/O Port   0x0000D880-0x0000D88F
Memory Address   0xFEBFB800-0xFEBFBBFF
IRQ Channel   IRQ 23
Driver   c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 23/8/2001 15:00)


THIS IS ME IDE

AND THIS SCSI

Name   Marvell RAID 614x
Manufacturer   Marvell Inc.
Status   OK
PNP Device ID   PCI\VEN_11AB&DEV_6141&SUBSYS_81D61043&REV_01\4&186DEF45&0&00E5
I/O Port   0x00009C00-0x00009C07
I/O Port   0x00009880-0x00009883
I/O Port   0x00009800-0x0000983F
I/O Port   0x00009480-0x0000949F
Memory Address   0xFA7FFC00-0xFA7FFFFF
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\mv614x.sys (, 33.63 KB (34,432 bytes), 27/5/2006 00:06)

Here
as usual disable Bootrom and RAID in your bios' Cosmos

[i_am_ugf]

it sees the ich7 now but when i put mtkflash r/m origin.bin it says fail to input file
Anu idea what may be wrong??

[i_am_ugf]

err SSt (SST39SR020)
fail to input file

[Grim187]

QUOTE(i_am_ugf @ May 27 2006, 11:04 AM)

err SSt (SST39SR020)
fail to input file

you still have RAID enabled or you SATA controller doesnt support Reading a Writing Firmware