Topic: Editing Mtkflash To Work With Your Sata Chipset (Read 1957 times)

Grim187 · « **Reply #60 on:** May 26, 2006, 09:08:00 AM »

QUOTE(ravabelly @ May 26 2006, 07:46 AM)

hello ppl, can i get your help?

I have a Sata chipset - Intel 82801GR/GH Sata Raid controller on an ABIT AL8 motherboard.

Can anyone confirm that this sata controller works with mtkflash? (read as much as I can on the forum)

I've tried editing mtkflash with hex editor and still no joy (altho I'm not convinced I knew what I was doing!)

The error message I keep getting is as follows:- "Failed to identify flash type" and the 360 led flashes until I swith it off.

Any help wud b much appreciated.

Thanx in advance

PS. Just realised my mistake - Chipset = Intel ICH7R Express Chipset (AL8)

ya i know alot of people that are haveing this problem, im not realy %100 on the solution to it, whats your sata in msinfo?, have you tryed booting dos then booting the 360 and hooking up the drive and runing mtkflash?, what firmware version do you have?

have you disabled all IDE channels and dissconnected all IDE Devices?

Also have you tryed "/SATA"?

ravabelly · « **Reply #61 on:** May 26, 2006, 09:11:00 AM »

QUOTE(Grim187 @ May 26 2006, 04:10 PM)

ya i know alot of people that are haveing this problem, im not realy %100 on the solution to it, whats your sata in msinfo?, have you tryed booting dos then booting the 360 and hooking up the drive and runing mtkflash?, what firmware version do you have?

have you disabled all IDE channels and dissconnected all IDE Devices?

Thanks for the reply!!

Here's me sata info:-

Name   Intel® 82801GR/GH SATA RAID Controller
Manufacturer   Intel
Status   OK
PNP Device ID   PCI\VEN_8086&DEV_27C3&SUBSYS_105D147B&REV_01\3&2411E6FE&0&FA
I/O Port   0x0000FA00-0x0000FA07
I/O Port   0x0000F900-0x0000F903
I/O Port   0x0000F800-0x0000F807
I/O Port   0x0000F700-0x0000F703
I/O Port   0x0000F600-0x0000F61F
Memory Address   0xFDFFE000-0xFDFFE3FF
IRQ Channel   IRQ 19
Driver   c:\windows\system32\drivers\iastor.sys (5.0.0.1026, 847.75 KB (868,096 bytes), 04/05/2005 15:57)
I havent unplugged IDE devices tho (dvdrom & dvd-r), also i got a promise ultra 133 ide controller, u rekon i shud unplug that unall?
firmware version of what?

Grim187 · « **Reply #62 on:** May 26, 2006, 09:20:00 AM »

QUOTE(ravabelly @ May 26 2006, 08:18 AM)

Thanks for the reply!!
I havent unplugged IDE devices tho (dvdrom & dvd-r), also i got a promise ultra 133 ide controller, u rekon i shud unplug that unall?
firmware version of what?

Use This if your worryed you dident edit right
the firmware version of your 360 TS drive (it should say on the top)
dont just unplug your IDE devices Dissable them in your cosmos, also make sure you dont have any other SATA devices pluged in

ravabelly · « **Reply #63 on:** May 26, 2006, 09:23:00 AM »

QUOTE(Grim187 @ May 26 2006, 04:27 PM)

http://www.1001megs.com/members/grim187/MTKFLASHICH7R.zip
the firmware version of your 360 TS drive (it should say on the top)
dont just unplug your IDE devices Dissable them in your cosmos, also make sure you dont have any other SATA devices pluged in

Thanks for the file will try it in a mo, the f/w = ms25.

Cheers

Dom334 · « **Reply #64 on:** May 26, 2006, 11:20:00 AM »

QUOTE(ravabelly @ May 26 2006, 04:30 PM)

Thanks for the file will try it in a mo, the f/w = ms25.

Cheers

seems like its the fw 25 thats the prob as we both have same problems with xbox360 but different computer mobo,s

is there anyone thats managed to flash a fw 25 drive also my hardware version is 04

Lilflip21 · « **Reply #65 on:** May 26, 2006, 12:55:00 PM »

trying to find a sata card i can just buy and throw in and this is the only one i can find around here since my built in sata ich6p aint working... anyone know if this card would work ... adaptect ...cause i would love to just rent that from bestbuy for the night and return it.. thanks for any info

Grim187 · « **Reply #66 on:** May 26, 2006, 01:13:00 PM »

QUOTE(Lilflip21 @ May 26 2006, 12:02 PM)

trying to find a sata card i can just buy and throw in and this is the only one i can find around here since my built in sata ich6p aint working... anyone know if this card would work ... adaptect ...cause i would love to just rent that from bestbuy for the night and return it.. thanks for any info

well if your gonna rent it then find out, it doesnt say anything about the chipset so i don't know, check my post 1 page back about making a informed decision when buying a sata controller card

Lilflip21 · « **Reply #67 on:** May 26, 2006, 03:44:00 PM »

hey grim sorry to keep bothering you but i found out that adaptec card has a sil3112 chipset... im finding some info on that but nothing too sure... got any advice on that chipset... think its woth a shot.. thanks again buddy i really wanna get this working this weekend

Grim187 · « **Reply #68 on:** May 26, 2006, 04:26:00 PM »

QUOTE(Lilflip21 @ May 26 2006, 02:51 PM)

hey grim sorry to keep bothering you but i found out that adaptec card has a sil3112 chipset... im finding some info on that but nothing too sure... got any advice on that chipset... think its woth a shot.. thanks again buddy i really wanna get this working this weekend

QUOTE

Name RocketRAID 1520 S-ATA Controller
Manufacturer HighPoint

PNP Device ID PCI\VEN_1103&DEV_0005&SUBSYS_00011103&REV_02\4&2AF9ED5&0&00F0
I/O Port 0x0000DC00-0x0000DC07
I/O Port 0x0000D880-0x0000D883
I/O Port 0x0000D800-0x0000D807
I/O Port 0x0000D480-0x0000D483
I/O Port 0x0000D000-0x0000D0FF
IRQ Channel IRQ 21
Driver c:\windows\system32\drivers\hpt3xx.sys (v2.36s, 40.97 KB (41,957 bytes), 10/12/2004 6:03 PM)

http://rapidshare.de...d_1520.rar.html

This PCI sata card works great for reading/writing FW with this edited mtkflash. Drive isnt detected in windows before/after flashing.

QUOTE

DETAILS:Fry's Electronics
Manufacturer: PPA Int'l: Parts, Peripherals & Accessories
UPC: 33250 00130
Fry's PLU: 3812387
instore price: $29.99+tax
online price: $24.99+ Overnight shipping was only $3 more than ground to buy online *http://shop2.outpost.com/product/3812387
confirmed working :yes
chipset: via vt6421
hex edited mtKflash to use with via vt6421 sata card for use on the sata master channel 0 which is the internal port. by Tbirdguy
the via 6421 with the hex edit mtkflash works perfect and i do recommend it to anyone looking for a pci sata card
http://rapidshare.de...ASHvia.zip.html

Found Here

i_am_ugf · « **Reply #69 on:** May 26, 2006, 05:05:00 PM »

Name   Marvell RAID 614x
Manufacturer   Marvell Inc.
Status   OK
PNP Device ID   PCI\VEN_11AB&DEV_6141&SUBSYS_81D61043&REV_01\4&186DEF45&0&00E5
I/O Port   0x00009C00-0x00009C07
I/O Port   0x00009880-0x00009883
I/O Port   0x00009800-0x0000983F
I/O Port   0x00009480-0x0000949F
Memory Address   0xFA7FFC00-0xFA7FFFFF
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\mv614x.sys (, 33.63 KB (34,432 bytes), 27/5/2006 00:06)

Name   SCSI/RAID Host Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   ACPI\PNPA000\4&41721A99&0
I/O Port   0x0000FFE0-0x0000FFEF
IRQ Channel   IRQ 9
Driver   c:\windows\system32\drivers\dtscsi.sys (, 217.90 KB (223,128 bytes), 19/5/2006 16:34)

Can someone help me out? my sata is based on ICH7r

Grim187 · « **Reply #70 on:** May 26, 2006, 05:16:00 PM »

QUOTE(i_am_ugf @ May 26 2006, 04:12 PM)

Name   Marvell RAID 614x
Manufacturer   Marvell Inc.
Status   OK
PNP Device ID   PCI\VEN_11AB&DEV_6141&SUBSYS_81D61043&REV_01\4&186DEF45&0&00E5
I/O Port   0x00009C00-0x00009C07
I/O Port   0x00009880-0x00009883
I/O Port   0x00009800-0x0000983F
I/O Port   0x00009480-0x0000949F
Memory Address   0xFA7FFC00-0xFA7FFFFF
IRQ Channel   IRQ 17
Driver   c:\windows\system32\drivers\mv614x.sys (, 33.63 KB (34,432 bytes), 27/5/2006 00:06)

Name   SCSI/RAID Host Controller
Manufacturer   (Standard mass storage controllers)
Status   OK
PNP Device ID   ACPI\PNPA000\4&41721A99&0
I/O Port   0x0000FFE0-0x0000FFEF
IRQ Channel   IRQ 9
Driver   c:\windows\system32\drivers\dtscsi.sys (, 217.90 KB (223,128 bytes), 19/5/2006 16:34)
Can someone help me out? my sata is based on ICH7r

you want me to help you out you have to tell me what your problem is

i_am_ugf · « **Reply #71 on:** May 26, 2006, 05:36:00 PM »

i figure out the first part that is AB114161 but i cant figureout the second part to edit with hex editor
I changed the mtkflash with the hex editor disable all ide and just plug in the toshiba dvd rom...with the edited ide the comp was like frozen with the original mtkflash it said nothing was found..

icechilly · « **Reply #72 on:** May 26, 2006, 05:36:00 PM »

little help needed here.

i went under msinfo and into SCSI but there is nothing listed there. but i know my chip is VT6237R if that makes any difference in solving my problem.

Grim187 · « **Reply #73 on:** May 26, 2006, 06:09:00 PM »

QUOTE(i_am_ugf @ May 26 2006, 04:43 PM)

i figure out the first part that is AB114161 but i cant figureout the second part to edit with hex editor
I changed the mtkflash with the hex editor disable all ide and just plug in the toshiba dvd rom...with the edited ide the comp was like frozen with the original mtkflash it said nothing was found..

CODE

009C 0098

QUOTE(icechilly @ May 26 2006, 04:43 PM)

little help needed here.

i went under msinfo and into SCSI but there is nothing listed there. but i know my chip is VT6237R if that makes any difference in solving my problem.

look around a little bit more its not always in SCSI, have you installed your SATA controllers driver?

If i keep getting n00b questions then i will stop answering questions,
READ THE HOLE THREAD BEFORE POSTING

I suggest if anyone has anymore problems e-mail me

icechilly · « **Reply #74 on:** May 26, 2006, 07:10:00 PM »

woah, no need to be busting out the red font.

just installed my drivers, lol cant believe i missed that

anyway i got it all working now thanks for the help!

Author Topic: Editing Mtkflash To Work With Your Sata Chipset (Read 1957 times)