Topic: To All With Nforce4 Chipset, Read This! (Read 243 times)

FlashKick · « **Reply #30 on:** June 22, 2006, 10:24:00 AM »

aw man, i thought these were tips on getting into mode b with slax for nforce 4 users (IMG:style_emoticons/default/sad.gif)

framer · « **Reply #31 on:** June 26, 2006, 12:43:00 PM »

You could also try booting in safe mode and flashing that way,it worked for me on a nf4 chipset with slax

GomerPyle · « **Reply #32 on:** June 26, 2006, 01:57:00 PM »

The Nforce drivers are buggy sand smuggy as hell If I were you guys id stick with the Windows default from now on!

Glad it worked for you guys cause I knew all along it was the buggy Nforce drivers!

n99wby · « **Reply #33 on:** June 26, 2006, 02:02:00 PM »

Its got nothing to do with Nforce 4 Its the SATA chip you have my nforce 4 boots fine admitidly the SATA chip cant put the 360 in ModeB

qckslvrpst · « **Reply #34 on:** June 26, 2006, 03:55:00 PM »

i have a gigabyte ga-k8n-sli motherboard and cant backup or flash fw my xbox light blinks but doesnt work

nraudigy2 · « **Reply #35 on:** August 21, 2006, 03:56:00 PM »

I have nf4 and using Xecutor kit, it takes couple reboots to get it to work in Windows XP Sp2. I had to switch between SATA slot until it is detected.

sith · « **Reply #36 on:** September 20, 2006, 09:16:00 PM »

gotta bump this up.. as i'm having the same problem.. i've got a msi neo4 nforce4 ultra mainboard with 4 sata slots, my toshiba samsung ms25 detects fine in windows, my bios and mtkflash for nf4 all see it, but when i try to dump the firmware it just hangs until i press esc and then i get the "should be = 70" msg can someone suggest a solution?

.sith.

thawu · « **Reply #37 on:** September 22, 2006, 01:13:00 PM »

I am also having the same problems, except I can't even read my firmware. I've been at it for 8 hours. I have tried all the differen combinations of the 'mtkflash r orig.bin' command but no luck. All I keep getting is status = 00, or 51, or 80 should be 70.

I'm using a shuttle sn25p which also has the nf4 chipset

any help would be great

thawu · « **Reply #38 on:** September 24, 2006, 02:22:00 AM »

successfully flashed, but can't detect the sammy drive with windows even after uninstalling the nvidia IDE drivers. Anything else it could be?

jdac · « **Reply #39 on:** October 22, 2006, 12:05:00 PM »

hello
first off, i have nf4, i just reinstalled windows, without installing mother boards sata drivers.
it boots up.

Hardware manager recognizes the samsung drive as a diskdrive not a cd or dvd drive?
I have been able to flash and all but this one is really getting on my nerves..

Room Supervisor · « **Reply #40 on:** November 06, 2006, 07:30:00 PM »

For those still having trouble with the NF4 chipset try this.

1. Set bios to boot from cd first

2. Connect SATA cable from xbox 360 DVD-ROM drive to pc SATA #3 with nothing on 4 (dont forget to connect a croc clip jumper from xbox chassis to pc chassis for ground)

3. Boot using Slax cd

4. After slax boots you shouldn't have to wait for log in: prompt just until it hangs and screen says drive is in Modeb (to check this eject Xbox 360 drive it should take to button press to close then after a couple seconds it will eject on its own) you are now in Modeb.

5. Hit the reset button on pc to boot up windows

6. Now install latest NVidia chipset drivers download here http://www.nvidia.com/content/drivers/drivers.asp

7. After install forces reboot drive should be visible.

Hope this helps worked great for me and now that drive is flashed I just use the open tray unplug trick to force Modeb.

P.S. I am using an ECS KN1 Lite Main board, and please no flaming for repeating pieces of other guides I just don't like posts full of links I think it just confuses people.

This post has been edited by Room Supervisor: Nov 7 2006, 03:31 AM

gokee2 · « **Reply #41 on:** December 26, 2006, 09:12:00 PM »

QUOTE(kezor @ May 18 2006, 06:36 PM)

yes my mobo works, do you have 8 sata ports in there
http://www.newegg.co...N82E16813136157

hey kezor. i have the same mobo as u. so how did you get it to work? im having issues. I use the slax and it goes thru all the scribble in the cmd prompt and then it gets into the login area. i reboot and eject the 360 drive and get in windows fine, but then i cant find my drive under hardware manager.

the scribble part is usually fast, i see my two optical drives listed but dont get to see a lot of other things. anyone can also asnwer if they have a clue as to whats going on. thanks.

gokee2 · « **Reply #42 on:** December 27, 2006, 09:37:00 AM »

QUOTE(gokee2 @ Dec 26 2006, 11:19 PM)

hey kezor. i have the same mobo as u. so how did you get it to work? im having issues. I use the slax and it goes thru all the scribble in the cmd prompt and then it gets into the login area. i reboot and eject the 360 drive and get in windows fine, but then i cant find my drive under hardware manager.

the scribble part is usually fast, i see my two optical drives listed but dont get to see a lot of other things. anyone can also asnwer if they have a clue as to whats going on. thanks.

FLASHED SUCCESSFULLY!!! Slax 2.0 messed me up big time. Used 2.1 instead and it worked like a charm. Thanks to every one and their HIGHLY informative and knowledgeable posts.

g0ssamer · « **Reply #43 on:** May 16, 2007, 06:42:00 PM »

I have a DFI LANPARTY UT nF3 250Gb motherboard and was unable to boot into windows with the drive plugged in although i was able to flash my drive in dos with no problems. Windows would either hang at startup or bluescreen if I tried to plug in my drive after startup. I though I could give this fix a shot even though it said it was for nF4 chipsets and it worked. Just though I would post my results for others that might have the same problem. THIS WORKS WITH NFORCE3 chipsets.

Author Topic: To All With Nforce4 Chipset, Read This! (Read 243 times)