Print

[antisniperspy]

QUOTE(soulwarrior @ Nov 14 2010, 09:35 AM)

As Cory explained to me, the old kxam.patch (ping patch) is programmed for 9199, and not the new dash. So you have two choices:

1. Delete kxam.patch and add this to the bottom of your launch.ini

[Settings]
pingpatch = true

2. open kxam.patch and replace 81 98 31 A8 with 81 91 D3 3C

*If you do number 1 without deleting kxam.patch, it will patch a random address, so be sure to delete it.

Checked it out and I do not have kxam.patch on hdd1 and I do have pingpatch = true. But it still does not work.

[bluntted]

QUOTE(dryan433 @ Nov 15 2010, 07:58 AM)

did you even replace the smc.bin with your own thats been modded for alternative points?

EasyFreeBoot has an option for AUD-CLAMP so I thought I'd be safe. I knew I should have just built my own image. Really pisses me off that I have to rip it apart and resolder shit. Idk why I can't boot back to xellous? I thought was supposed to be the backup to a bad flash.

[cytokinetic]

QUOTE(dryan433 @ Nov 14 2010, 08:19 PM)

this has the mem patch with it that's what dash launch is for to give back you xbox 1 compatibility and i will not recommend using old patches versions change addresses change etc so you could brick the image by using old patches

build it as normal how it says and install dash launch 2.05 you don't have to have anything set to boot this will add patches ie ping limit remove and with auto reboot on fatal errors so box should reboot and not just freeze this also detects if you boot an xbox 1 game and protects the mem so it can boot as normal

and old ping patch that you put on root of drive must be removed before installing dash launch or 30s ping will not get removed lol

Thanks for the info. I downloaded dashlaunch 2.05 and it does indeed say that in the instructions. I am going to wait until I get Kinect before updating and LT+. I don't want boot problems caused by the AP 2.5 games that are coming out now and I read that C4EVA is releasing it before Christmas. C4EVA is Awesome! Every time M$ tries a new form of protection, he bypasses it quickly!

[lupoz]

fbBuild_0.11 is out on xbins

Changes:
========
0.11
- add "jasper16a" LBA method as default for jasper
- add SMC check for encrypted and known hack SMC
- search for valid smc_config hash instead of hard coded
    offsets, support filename "config.bin"
- refine KV encryption check
- disable extended DVD auth for OSIG keyvaults (aka: AP25)
- random non-critical changes

I've tried and solve all ap2.5 disk problem,
Need for speed Hot Pursuit and Fable working without patching
(I'm running with sproofed samsung with fimware iX LT)
before, with fbBuild 0.1 I had disk unreadable error

as usual not safe for live...    

[dryan433]

QUOTE(bluntted @ Nov 15 2010, 09:02 PM)

EasyFreeBoot has an option for AUD-CLAMP so I thought I'd be safe. I knew I should have just built my own image. Really pisses me off that I have to rip it apart and resolder shit. Idk why I can't boot back to xellous? I thought was supposed to be the backup to a bad flash.
 

just rebuild and flash on ltp save having to pull wires apart may take longer to do but its better than messing anything else up you can ltp it without pulling the board out just a thought

[drake007]

Anyone here who got it to work with TMS=AUD_CLAMP and TDI=TRAY_OPEN?

I think Idon't know how to handle this atm. Maybe it's too simple for me.

I used this bestpig toolbox with my current freeboot 9199 nand. I did not change any data, just pointed to the nand file and the program created a new nand. When I put this on the console will it work or will I get a black screen? PRoblem is that my cable from the nandx is missing and i cannot flash this thing that's why I ask before I flash.

[doveman007]

I've tried building with Fbbuild and the bestpig toolbox, and after flashing with Flash360 I end up with an unbootable box.

I've got a few bad blocks which might be the problem but Flash360 has always successfully remapped them for me before, so I'm not sure what the problem is. I've got a Jasper512 by the way.

[syntaxerror329]

QUOTE(drake007 @ Nov 17 2010, 01:38 PM)

Anyone here who got it to work with TMS=AUD_CLAMP and TDI=TRAY_OPEN?

I think Idon't know how to handle this atm. Maybe it's too simple for me.

I used this bestpig toolbox with my current freeboot 9199 nand. I did not change any data, just pointed to the nand file and the program created a new nand. When I put this on the console will it work or will I get a black screen? PRoblem is that my cable from the nandx is missing and i cannot flash this thing that's why I ask before I flash.

Create a custom freeboot.
get the smc.bin form the data folder and patch it to match your wiring with smc_io by blackaddr.
let piggy finish and your all done.
keep your smc.bin file somewhere safe and in the future you can just replace the smc.bin file rather then making a new one everytime. For that matter if you already have a smc.bin that is patched you can just drag it in.

I would like to ask bestpig to add a check box for aud_clamp wiring. Almost everyone uses this now. It would make things alot simpler.

QUOTE(doveman007 @ Nov 17 2010, 02:34 PM)

I've tried building with Fbbuild and the bestpig toolbox, and after flashing with Flash360 I end up with an unbootable box.

I've got a few bad blocks which might be the problem but Flash360 has always successfully remapped them for me before, so I'm not sure what the problem is. I've got a Jasper512 by the way.

What jtag wiring method did you use? Do you get a specific error code?

[drake007]

QUOTE(syntaxerror329 @ Nov 17 2010, 09:36 PM)

Create a custom freeboot.
get the smc.bin form the data folder and patch it to match your wiring with smc_io by blackaddr.
let piggy finish and your all done.
keep your smc.bin file somewhere safe and in the future you can just replace the smc.bin file rather then making a new one everytime. For that matter if you already have a smc.bin that is patched you can just drag it in.

Problem is that the blackaddr tool just patches the aud_clamp an option for the tray_open is nowhere to be seen.

[syntaxerror329]

QUOTE(drake007 @ Nov 18 2010, 06:53 AM)

Problem is that the blackaddr tool just patches the aud_clamp an option for the tray_open is nowhere to be seen.

RTFM

Did you read the instructions that came with the program?
By default the program does just aud_clamp but with additional parameters you can patch any wiring you like.

[syntaxerror329]

CODE

C:\smc_util_v1.0a\smc_util>smc_util io smc.bin smcnew.bin /i

*** Xbox 360 SMC Utility ***
*** Version 1.0 by Blackaddr  ***

*** Xbox 360 SMC I/O Config Utility ***
*** Version 0.3a by Blackaddr  ***


INTERACTIVE MODE

1 - ARGON_DATA (Ring of light board)
2 - DB1F1 or alternate
3 - AUD_CLAMP (Q2N1)
4 - TRAY_OPEN (DVD power cable or connector)

Which I/O for TMS? [1-4]: 3
...using CC
Which I/O for TDI? [1-4]: 4
...using CF
Found the PCIe Start Write Bit bug @ 0x2E9E ...patched PCIe SWB bug..
Found the TMS code at 0x2DC3 and 0x2DCB ...patched TMS output...patched TMS delay.
Found the 1/4 TDI code at 0x2E23 ...patched TDI output.
Found the 2/4 TDI code at 0x2E49 ...patched TDI output.
Found the 3/4 TDI code at 0x2E60 ...patched TDI output.
Found the 4/4 TDI code at 0x2DB4 ...patched TDI output.
Found the TCLK delay code at 0x2DFA ...patched TCLK delay.
*** ARGON_DATA not used, attempting to remove ROL lockout code during JTAG ***
Found the ROL disable code at 0x2D9F ...removed ROL disable.
Found the ROL enable code at 0x2DA9 ...removed ROL enable.

The output file smcnew.bin must be re-encrypted before it can be flashed to the NAND.

[mossopinc]

QUOTE(syntaxerror329 @ Nov 18 2010, 02:46 PM)

Lets have you start off by getting the new version of smc_io released yesterday. It is on the front page here at x-scene.

When using bestpigs tool make sure have selected make a custom freeboot.
You will find smc.bin in the data folder.

Move it into the \smc_util_v1.0a\smc_util\ folder

Then run smc_util in "io" and "interactive mode". See my example below.

Once it is done copy your smcnew.bin file into the data folder. Rename it to smc.bin and close the data folder. Let bestpig tool finish and you should be good to go.

CODE

C:\smc_util_v1.0a\smc_util>smc_util io smc.bin smcnew.bin /i

*** Xbox 360 SMC Utility ***
*** Version 1.0 by Blackaddr  ***

*** Xbox 360 SMC I/O Config Utility ***
*** Version 0.3a by Blackaddr  ***
INTERACTIVE MODE

1 - ARGON_DATA (Ring of light board)
2 - DB1F1 or alternate
3 - AUD_CLAMP (Q2N1)
4 - TRAY_OPEN (DVD power cable or connector)

Which I/O for TMS? [1-4]: 3
...using CC
Which I/O for TDI? [1-4]: 4
...using CF
Found the PCIe Start Write Bit bug @ 0x2E9E ...patched PCIe SWB bug..
Found the TMS code at 0x2DC3 and 0x2DCB ...patched TMS output...patched TMS delay.
Found the 1/4 TDI code at 0x2E23 ...patched TDI output.
Found the 2/4 TDI code at 0x2E49 ...patched TDI output.
Found the 3/4 TDI code at 0x2E60 ...patched TDI output.
Found the 4/4 TDI code at 0x2DB4 ...patched TDI output.
Found the TCLK delay code at 0x2DFA ...patched TCLK delay.
*** ARGON_DATA not used, attempting to remove ROL lockout code during JTAG ***
Found the ROL disable code at 0x2D9F ...removed ROL disable.
Found the ROL enable code at 0x2DA9 ...removed ROL enable.

The output file smcnew.bin must be re-encrypted before it can be flashed to the NAND.

Which I/O for TDI? [1-4]:  parts says ERROR, couldn't find TMS data pattern. any clues as to why?


wait silly question prob but here goes, do i need to connect my 360 dvd drive to the pc to do this?

[syntaxerror329]

QUOTE(mossopinc @ Nov 18 2010, 04:23 PM)

Which I/O for TDI? [1-4]:  parts says ERROR, couldn't find TMS data pattern. any clues as to why?
wait silly question prob but here goes, do i need to connect my 360 dvd drive to the pc to do this?

What motherboard version do you have?
And yeah, the 360 DVD drive question was silly. Nothing to do with your issue at all.