Topic: Help.. Jtag Jasper.. 0 Reading Block (Read 104 times)

ahmer · « **on:** January 21, 2010, 11:04:00 PM »

I flashed my xenon with the same setup, diodes no resisters and all. Now trying to flash a jasper and its keeps trying to read saying 0 reading block ect....

please help,

ahmer · « **Reply #1 on:** January 22, 2010, 09:20:00 AM »

now Im just getting can not detect flash controller, and I have shortened the wires, only about 6 inches long

xxpittbullxx · « **Reply #2 on:** January 22, 2010, 09:42:00 AM »

Check your connections and make sure the diode is on the right way black ring towards the board

ahmer · « **Reply #3 on:** January 22, 2010, 09:44:00 AM »

I checked, and resolderd. Even used a multi meter, diode is face the right way. It is the same setup I used for xenon, and it worked great. Maybe I need to add the resisters for teh jasper ? begining to loose hope this is every going to work. been at it for 15 hours already..

ahmer · « **Reply #4 on:** January 22, 2010, 11:29:00 AM »

just tried with the resistors, and the diode, checked with volt meter, still no dice.. I had flashed using this same pc, xenon, with no resistors, and one diode.. WTH. any suggestions ?

ahmer · « **Reply #5 on:** January 22, 2010, 11:48:00 AM »

Got it working again, however still getthing the reading block error, sometimes its error: 0 reading block 0 and it keeps going on and on.

I have a 256mb jasper, and typed both -r16 command, and -r256?

anyone ? flash config is 00000400 ??

This post has been edited by ahmer: Jan 22 2010, 07:50 PM

ahmer · « **Reply #6 on:** January 22, 2010, 03:51:00 PM »

nobody ? anybod ? have a simliar problem ? Any suggestions for jaspers, anyone every have problems with jasper ? anyone do anything interesting to flash a jasper ? anyone ?

xxpittbullxx · « **Reply #7 on:** January 22, 2010, 08:04:00 PM »

What type of Diode are you using? Same as your xenon ?

ahmer · « **Reply #8 on:** January 22, 2010, 11:35:00 PM »

yes same as the xenon. I just re wired the whole, thing from scratch, and now i get error in diff way. First it says error: 127e reading block 0 and it gones on and on..

idk what to do anymore

strange thing is that the 360 actually turns on sometimes.

ahmer · « **Reply #9 on:** January 22, 2010, 11:57:00 PM »

just soldered the diode directly on the board rather then the lpt cable, still same issue. i removed the diode completly, and I get no flash config tool found.. so i know i need the diode.

This post has been edited by ahmer: Jan 23 2010, 08:05 AM

ToBbErT · « **Reply #10 on:** January 23, 2010, 06:28:00 AM »

The flashconfig should be 008A3020 for a 256mb. There's obvious something wrong if the 360 boots without pressing the on/off button or using the controller. Does the console still work fine without anything attached? You should first test it without any modification and see if it works properly.

ahmer · « **Reply #11 on:** January 23, 2010, 09:24:00 AM »

the 360 works fine, still, and according to free 60s guide, if the 360 lights turn on, then thats normal, and a good sign. Not the whole xbox, just the lights go on, which happens on some xboxs and is normal

Author Topic: Help.. Jtag Jasper.. 0 Reading Block (Read 104 times)