Topic: Problem With Degraded And 360 Flash Dump Tool? (Read 68 times)

Poopchute · « **on:** January 10, 2010, 03:49:00 PM »

OK...
I have a 512 Jasper and Im finally trying to get XBReboot installed. I am using an LPT cable. I have done 4 full reads just to be super safe. And I have also done 3 16mb reads. So far Read 1 and 3 match up with total commander 100% but Read 2 was off by 20 errors. So I tossed it. Now here comes my problem...
I have opened Read 1 and 3 up in 360 Flash Dump Tool v0.91 and I got my CB,CD, and CE info but on the right hand side it says "No FS root". I don't get any of that info I have seen in other dumps from tutorials. Also I have tried using Degraded 1.1 but when I open up Read 1 or 3 it just crashes and asks if I want to debug or check online for a solution? Is there something wrong with my dumps? Or are there bugs in these 2 tools? Or have I done something wrong?
Thanks

Poopchute · « **Reply #1 on:** January 10, 2010, 09:20:00 PM »

anyone got any ideas?

xxpittbullxx · « **Reply #2 on:** January 10, 2010, 09:36:00 PM »

Flash Dump Tool v0.91 and Degraded are not Compatible with Big block Nands as of yet

Poopchute · « **Reply #3 on:** January 10, 2010, 10:00:00 PM »

I know that. Im not trying to check a large nand in either program. I did what I thought you were supposed to do to make a small 16mb image so that I could check my CB info. Problem is even after I hex edit them to say 2004-2005 it still wont open properly in either one. I just plain old cant open up a 16mb image in degraded 1.1 but I can open it in 360 flash tool. But on the right hand side mine says no fs root.

ujackspades · « **Reply #4 on:** January 10, 2010, 11:02:00 PM »

Hey can you give me the link to the degraded program? Searched everywhere and I can't find it.

Thanks!

Poopchute · « **Reply #5 on:** January 10, 2010, 11:07:00 PM »

it was on xbins...

xxpittbullxx · « **Reply #6 on:** January 11, 2010, 07:06:00 AM »

Whether you dump the whole 512 or 16megs its still a big block, so support is limited

Poopchute · « **Reply #7 on:** January 11, 2010, 09:14:00 AM »

See I tried to use a 16 mb dump of a 512 nand and tried to use that to extract the rawk and rawconfig and then I've tried injecting those into XBReboot _JasperBB_8955_3 which is for BigBlocks? So I used a small nand dump with a Big Block version of XBReeboot. That didnt work.
So then I tried taking another 16mb nand dump and used that to do the same process to XBReboot_Jasper16_8955_3. That didnt work...

xxpittbullxx · « **Reply #8 on:** January 11, 2010, 09:45:00 AM »

Cant you just grab the rkv.bin and rconfig.bin out of your orig. 512 dump?
That would be my recommendation

Poopchute · « **Reply #9 on:** January 11, 2010, 10:06:00 AM »

Well I have done that. But Ive tried injecting that into the "jasper_6723_hack_for_256mb_512mb" once and tried that. Didnt work.
I have 2-3 really basic questions. First off, there is the LPT wires. I can leave those soldered in for the entire process from reading to writing to even leaving them soldered in while I boot the xbox up afterward to check if its working? As long as I unplug the lpt end from my flashng computer? But what about the 3 SPI wires? Do I need to unsolder them afterward to check if everythings working? Cause I was following this thread and they mention that...http://forums.xbox-scene.com/index.php?showtopic=698328
Im just worried that I might have a good flash but Im supposed to unsolder the SPI wires afterward, and if I dont Im just gonna keep getting rrod.

Poopchute · « **Reply #10 on:** January 11, 2010, 11:50:00 AM »

OK I managed to take (jasper_6723_hack_for_256mb_512mb) and renamed it xbr.bin and did a (NandPro lpt: -w64 xbr.bin) It now boots to xell. But I had to use a AV cable not a HDMI to get video.

Poopchute · « **Reply #11 on:** January 11, 2010, 01:29:00 PM »

QUOTE(xxpittbullxx @ Jan 11 2010, 10:45 AM)

Cant you just grab the rkv.bin and rconfig.bin out of your orig. 512 dump?
That would be my recommendation

What size should I use? nandpro orig.bin: -r16 rawkv.bin 1 1 or nandpro orig.bin: -r64 rawkv.bin 1 1 ?
Or 512?
Like Ive said I have managed to get Xell booted and get my cpu key but thats it...

So what size should I use to extract the rawk and rawconfig from a 512 nand? Or should I be using a 16mb version of my nand instead since there is little support? I think if I get this Ill be done...

xxpittbullxx · « **Reply #12 on:** January 11, 2010, 06:30:00 PM »

QUOTE(Poopchute @ Jan 11 2010, 03:29 PM)

What size should I use? nandpro orig.bin: -r16 rawkv.bin 1 1 or nandpro orig.bin: -r64 rawkv.bin 1 1 ?
Or 512?
Like Ive said I have managed to get Xell booted and get my cpu key but thats it...

So what size should I use to extract the rawk and rawconfig from a 512 nand? Or should I be using a 16mb version of my nand instead since there is little support? I think if I get this Ill be done...

nandpro orig.bin: -r512 rawkv.bin 1 1

Author Topic: Problem With Degraded And 360 Flash Dump Tool? (Read 68 times)