Topic: Easiest Way To Do Jtag Hack On Falcon Motherboard (Read 170 times)

MasterGouken · « **Reply #15 on:** October 25, 2009, 06:45:00 AM »

QUOTE(saint24 @ Oct 25 2009, 10:30 AM)

where does the other end of the diode go? i get the pin header hole part but the other end the blue dot covers two points

The other end of the diode doesnt go to the motherboard, it goes to pin 11 on the lpt connector (its colour coded, same as all the other points).

saint24 · « **Reply #16 on:** October 25, 2009, 09:50:00 AM »

Cheers for that couldn't see it for looking also does anyone know how you do this via USB?

MasterGouken · « **Reply #17 on:** October 25, 2009, 02:10:00 PM »

QUOTE(saint24 @ Oct 25 2009, 05:50 PM)

Cheers for that couldn't see it for looking also does anyone know how you do this via USB?

I have done it via usb. You'll need an Arm USB dev board (Olimex LPC-H2148) which you'll need to program 1st with an rs232 level shifter and the xspiflash.hex file included with nandpro.
Then wire up according to the nandpro readme file. The command is then NandPro usb: -r16 nand.bin to dump your nand.

This post has been edited by MasterGouken: Oct 25 2009, 09:11 PM

saint24 · « **Reply #18 on:** October 26, 2009, 05:02:00 PM »

this is doing my head in

got it wired right done2 dumps booth read ok and are compared the same

but

when flashed with falcon hack.bin i get 3 red lights as soon as i turn it on
is it because its not the right bin file i looked up my board and i identified it as falcon but which are the others with hdmi its possible i identified the board wrong

MasterGouken · « **Reply #19 on:** October 27, 2009, 05:02:00 AM »

Did you remove power completely after flashing? (pull the power lead for a few seconds)

Gridern07 · « **Reply #20 on:** October 29, 2009, 04:20:00 PM »

I have made several dumps and I can't get degraded to open any of them. it says can't read file. do you think I should continue dumping until degraded can open one before I flash xell. by the way my board is a zephyr.

bar807 · « **Reply #21 on:** November 18, 2009, 12:43:00 PM »

Will a PCi lpt card work?

nomarx · « **Reply #22 on:** November 25, 2009, 02:37:00 AM »

Hello, thanks for nice information.

If I just want to get back HDD functionality on banned console, I need to do extra connections too?

Thanks

360player · « **Reply #23 on:** December 07, 2009, 11:17:00 PM »

I'm trying to do this with a falcon board to get the cpu key.. Do we still have to wire up the jtag to dump the nand? Or Do we just have to do it to get the cpu key?
Also is it normal that when you have everything soldered up the xbox powers on and shows video through the vga cable but when I plug the LPT port into the computer it won't power on, it just shuts off.
Is that normal.

I can't get nanpro to start doing anything so maybe something is not right?

shawndezy115 · « **Reply #24 on:** December 08, 2009, 07:50:00 AM »

(360player) it is my understanding that you only need power to the 360. so it is not turned on while you are doing all of this.
once you have done your reading and writing you disconect your lpt and then disconect the power to your 360 for a moment and then boot up your 360.

good luck

Author Topic: Easiest Way To Do Jtag Hack On Falcon Motherboard (Read 170 times)